8/7/25, 10:37 PM ASE A6
ASE A6 TEST BANK EXAM PREP 2025-2026 (ELECTRICAL
& ELECTRONIC SOUNDS) LATEST VERSION WITH
COMPLETE QUESTIONS AND ACCURATE DETAILED
ANSWERS \VERIFIED SOLUTIONS \BRAND NEW
Which of the following b. Copper stranded type
describes the MOST
common type of electrical Copper stranded type electrical wiring is the correct
wiring used in answer because the other types are not common.
instrument lighting?
a. Aluminum stranded type
b. Copper stranded type
c. Twisted pair type
d. Solid copper type
What type of solder is c. Rosin core
required to repair the
instrument panel wiring? Rosin core is the specified type of solder to use on any
electrical repair to insure integrity.
a. Acid core
b. 60/40 with no flux
c. Rosin core
d. 50/50 with acid paste flux
A dash indicator warning d. Bulb
lamp does not light when
the key is in the ON or Checking the bulb is the quickest and easiest thing to do.
START positions. What
should you check first?
a. Sending unit
b. Wiring
/ 1/53
,8/7/25, 10:37 PM ASE A6
c. Battery level
d. Bulb
If a fuel gauge reads full, c. Wire to sending unit grounded
which of the following is
the MOST likely cause? A wire to the sending unit being grounded is the most likely cause
on most systems.
a. A broken gauge
b. Float stuck in the up position
c. Wire to sending unit
grounded
d. An open fuse
A technician is replacing B. Disconnect the negative battery cable prior to beginning the
the electronic module for repair
the park assist system.
Which of the following
practices would most likely
be required to assure a
trouble free repair?
A. Remove the engine
noise dampening cover
B. Disconnect the negative
battery cable prior to
beginning the repair
C. Remove the bumper
retaining fasteners
D. Remove the rear hatch lock
assembly
A vehicle is in the repair shop Both A and B
with an inoperative power
window. During
diagnosis, a blown power
window fuse is located.
Technician A says that a
short to ground between
/ 2/53
,8/7/25, 10:37 PM ASE A6
the switch and the motor
could be the cause.
Technician B says that a
tight power window motor
could be the cause. Who
is correct?
A vehicle is in the repair A Only?
shop for a dead battery.
During the diagnosis, an
excessive parasitic draw is
found. Technician A says
that a diode problem in the
generator
could be the cause.
Technician B says that an
"open" glove box bulb
could be the
problem. Who is correct?
Which of the following D. The color and circuit number of a wire
details would be the most
likely item to be located on
a wiring
diagram?
A. The location of a component
B. A flowchart for
troubleshooting an
electrical problem
C. The current rating of a circuit
D. The color and circuit number
of a wire
Technician A states that B Only
the scan tool receives data
from a connector located on
the ECM. Technician B
states that the scan tool
connects to the data bus
using data link connector.
Who is correct?
/ 3/53
, 8/7/25, 10:37 PM ASE A6
A vehicle is being Neither A or B
diagnosed for a battery
problem. Technician A says
that the battery open
circuit voltage should be
12.6 volts before
performing a digital
battery test.
Technician B says that a
battery can be accurately
load-tested if it has an open
circuit voltage of 12 volts. Who
is correct?
Which of the following A. A battery jump box with a 12 volt accessory connecting wire
tools can be used to
maintain electronic
memory functions while a
battery is disconnected?
A. A battery jump box with a
12 volt accessory
connecting wire
B. A scan tool
C. A digital multimeter
D. A test light
All of the following details are C. Battery manufacturer
critical when choosing a
replacement battery for a
vehicle EXCEPT:
A. Cold cranking some of the
battery
B. Reserve capacity of the
battery
C. Battery manufacturer
D. Physical dimensions of the
battery case
What is the most likely B. Wire brush
method to be used when
professionally cleaning
battery cable clamps?
A. Pneumatic die grinder
B. Wire brush
/ 4/53
ASE A6 TEST BANK EXAM PREP 2025-2026 (ELECTRICAL
& ELECTRONIC SOUNDS) LATEST VERSION WITH
COMPLETE QUESTIONS AND ACCURATE DETAILED
ANSWERS \VERIFIED SOLUTIONS \BRAND NEW
Which of the following b. Copper stranded type
describes the MOST
common type of electrical Copper stranded type electrical wiring is the correct
wiring used in answer because the other types are not common.
instrument lighting?
a. Aluminum stranded type
b. Copper stranded type
c. Twisted pair type
d. Solid copper type
What type of solder is c. Rosin core
required to repair the
instrument panel wiring? Rosin core is the specified type of solder to use on any
electrical repair to insure integrity.
a. Acid core
b. 60/40 with no flux
c. Rosin core
d. 50/50 with acid paste flux
A dash indicator warning d. Bulb
lamp does not light when
the key is in the ON or Checking the bulb is the quickest and easiest thing to do.
START positions. What
should you check first?
a. Sending unit
b. Wiring
/ 1/53
,8/7/25, 10:37 PM ASE A6
c. Battery level
d. Bulb
If a fuel gauge reads full, c. Wire to sending unit grounded
which of the following is
the MOST likely cause? A wire to the sending unit being grounded is the most likely cause
on most systems.
a. A broken gauge
b. Float stuck in the up position
c. Wire to sending unit
grounded
d. An open fuse
A technician is replacing B. Disconnect the negative battery cable prior to beginning the
the electronic module for repair
the park assist system.
Which of the following
practices would most likely
be required to assure a
trouble free repair?
A. Remove the engine
noise dampening cover
B. Disconnect the negative
battery cable prior to
beginning the repair
C. Remove the bumper
retaining fasteners
D. Remove the rear hatch lock
assembly
A vehicle is in the repair shop Both A and B
with an inoperative power
window. During
diagnosis, a blown power
window fuse is located.
Technician A says that a
short to ground between
/ 2/53
,8/7/25, 10:37 PM ASE A6
the switch and the motor
could be the cause.
Technician B says that a
tight power window motor
could be the cause. Who
is correct?
A vehicle is in the repair A Only?
shop for a dead battery.
During the diagnosis, an
excessive parasitic draw is
found. Technician A says
that a diode problem in the
generator
could be the cause.
Technician B says that an
"open" glove box bulb
could be the
problem. Who is correct?
Which of the following D. The color and circuit number of a wire
details would be the most
likely item to be located on
a wiring
diagram?
A. The location of a component
B. A flowchart for
troubleshooting an
electrical problem
C. The current rating of a circuit
D. The color and circuit number
of a wire
Technician A states that B Only
the scan tool receives data
from a connector located on
the ECM. Technician B
states that the scan tool
connects to the data bus
using data link connector.
Who is correct?
/ 3/53
, 8/7/25, 10:37 PM ASE A6
A vehicle is being Neither A or B
diagnosed for a battery
problem. Technician A says
that the battery open
circuit voltage should be
12.6 volts before
performing a digital
battery test.
Technician B says that a
battery can be accurately
load-tested if it has an open
circuit voltage of 12 volts. Who
is correct?
Which of the following A. A battery jump box with a 12 volt accessory connecting wire
tools can be used to
maintain electronic
memory functions while a
battery is disconnected?
A. A battery jump box with a
12 volt accessory
connecting wire
B. A scan tool
C. A digital multimeter
D. A test light
All of the following details are C. Battery manufacturer
critical when choosing a
replacement battery for a
vehicle EXCEPT:
A. Cold cranking some of the
battery
B. Reserve capacity of the
battery
C. Battery manufacturer
D. Physical dimensions of the
battery case
What is the most likely B. Wire brush
method to be used when
professionally cleaning
battery cable clamps?
A. Pneumatic die grinder
B. Wire brush
/ 4/53
