NCCER Core Module 1
Study online at https://quizlet.com/_a3b5go
1. Companies with strong safety cultures usually have Turnover
lower?
2. Poor lighting, excessive noise, and inadequate guards unsafe conditions
for moving parts are examples of
3. The activity that consists of breaking a job into its Job Safety Analysis
component tasks and then analyzing each step for
potential hazards is called a _____.
4. A measure of the probability, consequences, and expo- Risk
sure related to an event is referred to as _____.
5. If there is a hole in the floor of a structure, the pre- Cover and mark it
ferred method of protecting workers from falls is to
_____.
6. The D-ring or support point on a safety harness should Between the shoulder
be placed _____. blades, middle of your
back
7. A personal fall arrest system should be inspected Competent person
monthly by a _____.
8. Lanyards that have no shock-absorbing features are Positioning
used for _____.
9. When placing a ladder against a platform or roof, the 3 Feet
top of the ladder should extend above the point where
the ladder touches the platform or roof by at least
_____.
10. toe boards, debris nets, or
canopies
1/6
, NCCER Core Module 1
Study online at https://quizlet.com/_a3b5go
When performing overhead work on scaffolding, what
protective measures must be taken to prevent objects
from falling and striking a person below?
11. When stacking materials such as bricks or block, do not 4:1 Ratio
stack materials beyond a _____.
12. Benching systems are prohibited in _____. Type C
13. In the absence of other information, all soil in an exca- Type C
vation should be treated as if it is _____.
14. Daily inspection of an excavation must be performed Competent person
by a(n) _____.
15. One of the most common grounding systems used for 3-wire system
protection against accidental electrical shock is the
_____.
16. A polarized electrical receptacle is used for _____. double insulated tools
17. A system that protects workers from the release of Lock-out/ Tag-out
hazardous energy while they work with machines and
equipment is referred to as _____.
18. In a lockout/tagout situation, a personal lock and tag Person who applied them
must be removed by _____.
19. Hard hats should be made of fiberglass or _____. Reinforced plastic
20. A good general rule about hearing protection is that it 2 feet away
should be used if you must raise your voice for
someone to hear you when they are _____.
2/6
Study online at https://quizlet.com/_a3b5go
1. Companies with strong safety cultures usually have Turnover
lower?
2. Poor lighting, excessive noise, and inadequate guards unsafe conditions
for moving parts are examples of
3. The activity that consists of breaking a job into its Job Safety Analysis
component tasks and then analyzing each step for
potential hazards is called a _____.
4. A measure of the probability, consequences, and expo- Risk
sure related to an event is referred to as _____.
5. If there is a hole in the floor of a structure, the pre- Cover and mark it
ferred method of protecting workers from falls is to
_____.
6. The D-ring or support point on a safety harness should Between the shoulder
be placed _____. blades, middle of your
back
7. A personal fall arrest system should be inspected Competent person
monthly by a _____.
8. Lanyards that have no shock-absorbing features are Positioning
used for _____.
9. When placing a ladder against a platform or roof, the 3 Feet
top of the ladder should extend above the point where
the ladder touches the platform or roof by at least
_____.
10. toe boards, debris nets, or
canopies
1/6
, NCCER Core Module 1
Study online at https://quizlet.com/_a3b5go
When performing overhead work on scaffolding, what
protective measures must be taken to prevent objects
from falling and striking a person below?
11. When stacking materials such as bricks or block, do not 4:1 Ratio
stack materials beyond a _____.
12. Benching systems are prohibited in _____. Type C
13. In the absence of other information, all soil in an exca- Type C
vation should be treated as if it is _____.
14. Daily inspection of an excavation must be performed Competent person
by a(n) _____.
15. One of the most common grounding systems used for 3-wire system
protection against accidental electrical shock is the
_____.
16. A polarized electrical receptacle is used for _____. double insulated tools
17. A system that protects workers from the release of Lock-out/ Tag-out
hazardous energy while they work with machines and
equipment is referred to as _____.
18. In a lockout/tagout situation, a personal lock and tag Person who applied them
must be removed by _____.
19. Hard hats should be made of fiberglass or _____. Reinforced plastic
20. A good general rule about hearing protection is that it 2 feet away
should be used if you must raise your voice for
someone to hear you when they are _____.
2/6
