Millwright study with correct
answers 2025
What is the biggest causes of injuries on the job - CORRECT ANSWER-Carelessness
or horseplay
Rags used to clean up solvents and oils must be disposed of in: - CORRECT
ANSWER-An "Approved metal container"
All personal protective equipment (PPE) must be: - CORRECT ANSWER-CSA Aproved
A green tag on boots indicates that: - CORRECT ANSWER-The boots are CSA
aprroved
People that are the persons who have locks on a locked out piece of equipment are
known as: - CORRECT ANSWER-Authorized people
Double insulated tools are: - CORRECT ANSWER-Some hand-held tools which have
an insulated handle or housing
Zero mechanical state/Zero energy state refers to: - CORRECT ANSWER-A piece of
equipment which has been locked out and all its sources of energy have been made
inoperative
Green Triangle "A" - CORRECT ANSWER-Fires involving ordinary combustibles (wood,
paper, organics)
,Red Square "B" - CORRECT ANSWER-Fires involving flammable or combustible
vapours
Blue Circle "C" - CORRECT ANSWER-Fires involving energized electrical equipment
Yellow Star "C" - CORRECT ANSWER-fires involving combustible metals (Magnesium
Aluminium)
Fire Extinguishers:
P
A
S
S - CORRECT ANSWER-P- Pull the pin
A - Aim the nozzle at the base of the flame
S - Squeeze the trigger
S - Sweep the nozzle at the base of the flame
MSDS Stands for - CORRECT ANSWER-Material Safety Data Sheets
MSDS's must be: - CORRECT ANSWER-MSDS's must be replaced every 3 years and
you must know where they are in your workplace
What determines your PPE? - CORRECT ANSWER-The hazards, your PPE is
determined by the hazards
What attributes must a millwrights clothing have? - CORRECT ANSWER-your clothing
should provide sufficient insulation, be flame retardant, and smooth
3 Things you have the right to know in regards to safe work are: - CORRECT
ANSWER-1) you have the right to know (hazards of the work)
2) you have the right to refuse (unsafe work)
3) you have the right to participate (safety planning)
Flashpoint is: - CORRECT ANSWER-The lowest temperature at which vapours from a
volatile liquid will ignite
The Work Place Hazardous Information System
(WHIMIS) deals with: - CORRECT ANSWER-WHIMIS covers the following areas:
-Hazard identification
-Labeling controlled products
-Provisions for MSDS's
-Education and training
-Ingredient disclosure
-Protection of product "trade secrets"
,Cohesive Forces are: - CORRECT ANSWER-The force at which molecules in matter
are attracted to each other. For example a large load can be hung from steel cable due
to the cables steel strong cohesive force.
Adhesive Forces are: - CORRECT ANSWER-Molecules which are not alike will often
share a force of attraction similar to cohesion. This force is known as adhesive force.
Example: paint to concrete
Ultimate stress: - CORRECT ANSWER-The point at which material ruptures/fails under
stress loads
Tensile strength: - CORRECT ANSWER-The resistance ability of materials to being
pulled apart.
Compressive strength - CORRECT ANSWER-The resistance to compressive forces.
Example: concretes ability to hold loads
Shear strength - CORRECT ANSWER-The ability of a material to resist forces that try to
slide part of an object along itself (clean break)
Fatigue Strength - CORRECT ANSWER-The ability to withstand repeated alternating
stresses
Elasticity - CORRECT ANSWER-The ability of material to return to its original
dimensions after it has been affected by force
Elastic limit (yield Strength) - CORRECT ANSWER-The maximum force a solid can
withstand before becoming permanently deformed
Plasticity - CORRECT ANSWER-The ability for a material to retain shape permanently
after a deforming force is removed. Example: metal is heated to increase its plasticity
Ductility - CORRECT ANSWER-The ability to stretch and maintain a new shape. For
example material can be drawn into a wire. The finer the wire can be produced the more
ductile the material is
Malleability - CORRECT ANSWER-The ability of a material to be permanently deformed
by compressive forces. Examples would be rolling, pressing and forging processes.
Brittleness - CORRECT ANSWER-material which breaks without noticeable plastic
deformation. A substance may be quite hard but lack strength due to brittleness. An
example would be glass
Toughness - CORRECT ANSWER-The ability of a material to withstand shockloads
, Hardness - CORRECT ANSWER-Materials ability to resist force of penetration.
Penetration is an attempt to push molecules apart
Electrical conductivity - CORRECT ANSWER-The ability of a material to conduct
electricity
- Conductors (Copper, Aluminium, silver)
-Insulators (Rubber, Bakelite, Glass, Oil)
Thermal conductivity - CORRECT ANSWER-Determines the rate of heat flow through a
material.
Electrochemical Reaction of metals - CORRECT ANSWER-When two different metals
are in contact with each other and water is present an electric current is produced. The
electron flow has a chemical corrosion effect
Volatility - CORRECT ANSWER-A measure of how quickly a liquid will evaporate. A
liquid is said to be highly volatile if it changes from a liquid to a gas quickly
Viscosity - CORRECT ANSWER-A measure of a liquids resistance to flow. The higher
the viscosity of a liquid, the greater its resistance to being poured
Bi-Metallic Strip Thermometers - CORRECT ANSWER-A strip of two dissimilar metals
bonded together. The two metals have different thermal conductivity properties as one
will stay rigid and the other will bend.
Example: a temperature gauge with a pointer.
Pyrometers - CORRECT ANSWER-An instrument that measures temperature beyond
the range of normal thermometer. There are various types of pyrometers:
-Optical pyrometer: measures temperature through color observation (Flame Scanner)
-Thermoelectric pyrometer: Resistance thermometers. As their temperature changes
there is a direct change in resistance. (Flame Rod)
Thermocouples - CORRECT ANSWER-Consist of an electrical circuit terminating with
the junction of 2 different metals, (Hot Junction). When the temperature of the junction is
raised a voltage is produced. The hotter the temperature the larger the voltage.
Coefficients of Expansion - CORRECT ANSWER-Predict the dimension changes of a
material as the temperature changes. Example Coefficient for steel - 0.000,012 per
degree Celsius
Heat Transfer - CORRECT ANSWER-Heat flows from one object to another in 3 forms:
-Conduction
-Convection
-Radiation
answers 2025
What is the biggest causes of injuries on the job - CORRECT ANSWER-Carelessness
or horseplay
Rags used to clean up solvents and oils must be disposed of in: - CORRECT
ANSWER-An "Approved metal container"
All personal protective equipment (PPE) must be: - CORRECT ANSWER-CSA Aproved
A green tag on boots indicates that: - CORRECT ANSWER-The boots are CSA
aprroved
People that are the persons who have locks on a locked out piece of equipment are
known as: - CORRECT ANSWER-Authorized people
Double insulated tools are: - CORRECT ANSWER-Some hand-held tools which have
an insulated handle or housing
Zero mechanical state/Zero energy state refers to: - CORRECT ANSWER-A piece of
equipment which has been locked out and all its sources of energy have been made
inoperative
Green Triangle "A" - CORRECT ANSWER-Fires involving ordinary combustibles (wood,
paper, organics)
,Red Square "B" - CORRECT ANSWER-Fires involving flammable or combustible
vapours
Blue Circle "C" - CORRECT ANSWER-Fires involving energized electrical equipment
Yellow Star "C" - CORRECT ANSWER-fires involving combustible metals (Magnesium
Aluminium)
Fire Extinguishers:
P
A
S
S - CORRECT ANSWER-P- Pull the pin
A - Aim the nozzle at the base of the flame
S - Squeeze the trigger
S - Sweep the nozzle at the base of the flame
MSDS Stands for - CORRECT ANSWER-Material Safety Data Sheets
MSDS's must be: - CORRECT ANSWER-MSDS's must be replaced every 3 years and
you must know where they are in your workplace
What determines your PPE? - CORRECT ANSWER-The hazards, your PPE is
determined by the hazards
What attributes must a millwrights clothing have? - CORRECT ANSWER-your clothing
should provide sufficient insulation, be flame retardant, and smooth
3 Things you have the right to know in regards to safe work are: - CORRECT
ANSWER-1) you have the right to know (hazards of the work)
2) you have the right to refuse (unsafe work)
3) you have the right to participate (safety planning)
Flashpoint is: - CORRECT ANSWER-The lowest temperature at which vapours from a
volatile liquid will ignite
The Work Place Hazardous Information System
(WHIMIS) deals with: - CORRECT ANSWER-WHIMIS covers the following areas:
-Hazard identification
-Labeling controlled products
-Provisions for MSDS's
-Education and training
-Ingredient disclosure
-Protection of product "trade secrets"
,Cohesive Forces are: - CORRECT ANSWER-The force at which molecules in matter
are attracted to each other. For example a large load can be hung from steel cable due
to the cables steel strong cohesive force.
Adhesive Forces are: - CORRECT ANSWER-Molecules which are not alike will often
share a force of attraction similar to cohesion. This force is known as adhesive force.
Example: paint to concrete
Ultimate stress: - CORRECT ANSWER-The point at which material ruptures/fails under
stress loads
Tensile strength: - CORRECT ANSWER-The resistance ability of materials to being
pulled apart.
Compressive strength - CORRECT ANSWER-The resistance to compressive forces.
Example: concretes ability to hold loads
Shear strength - CORRECT ANSWER-The ability of a material to resist forces that try to
slide part of an object along itself (clean break)
Fatigue Strength - CORRECT ANSWER-The ability to withstand repeated alternating
stresses
Elasticity - CORRECT ANSWER-The ability of material to return to its original
dimensions after it has been affected by force
Elastic limit (yield Strength) - CORRECT ANSWER-The maximum force a solid can
withstand before becoming permanently deformed
Plasticity - CORRECT ANSWER-The ability for a material to retain shape permanently
after a deforming force is removed. Example: metal is heated to increase its plasticity
Ductility - CORRECT ANSWER-The ability to stretch and maintain a new shape. For
example material can be drawn into a wire. The finer the wire can be produced the more
ductile the material is
Malleability - CORRECT ANSWER-The ability of a material to be permanently deformed
by compressive forces. Examples would be rolling, pressing and forging processes.
Brittleness - CORRECT ANSWER-material which breaks without noticeable plastic
deformation. A substance may be quite hard but lack strength due to brittleness. An
example would be glass
Toughness - CORRECT ANSWER-The ability of a material to withstand shockloads
, Hardness - CORRECT ANSWER-Materials ability to resist force of penetration.
Penetration is an attempt to push molecules apart
Electrical conductivity - CORRECT ANSWER-The ability of a material to conduct
electricity
- Conductors (Copper, Aluminium, silver)
-Insulators (Rubber, Bakelite, Glass, Oil)
Thermal conductivity - CORRECT ANSWER-Determines the rate of heat flow through a
material.
Electrochemical Reaction of metals - CORRECT ANSWER-When two different metals
are in contact with each other and water is present an electric current is produced. The
electron flow has a chemical corrosion effect
Volatility - CORRECT ANSWER-A measure of how quickly a liquid will evaporate. A
liquid is said to be highly volatile if it changes from a liquid to a gas quickly
Viscosity - CORRECT ANSWER-A measure of a liquids resistance to flow. The higher
the viscosity of a liquid, the greater its resistance to being poured
Bi-Metallic Strip Thermometers - CORRECT ANSWER-A strip of two dissimilar metals
bonded together. The two metals have different thermal conductivity properties as one
will stay rigid and the other will bend.
Example: a temperature gauge with a pointer.
Pyrometers - CORRECT ANSWER-An instrument that measures temperature beyond
the range of normal thermometer. There are various types of pyrometers:
-Optical pyrometer: measures temperature through color observation (Flame Scanner)
-Thermoelectric pyrometer: Resistance thermometers. As their temperature changes
there is a direct change in resistance. (Flame Rod)
Thermocouples - CORRECT ANSWER-Consist of an electrical circuit terminating with
the junction of 2 different metals, (Hot Junction). When the temperature of the junction is
raised a voltage is produced. The hotter the temperature the larger the voltage.
Coefficients of Expansion - CORRECT ANSWER-Predict the dimension changes of a
material as the temperature changes. Example Coefficient for steel - 0.000,012 per
degree Celsius
Heat Transfer - CORRECT ANSWER-Heat flows from one object to another in 3 forms:
-Conduction
-Convection
-Radiation