APL 250 Beaker Anatomic Pathology questions
with accurate answers
_________ protocols can be linked to test records on the Specialty
Testing form so they are selected by default when users build a case.
________ protocols can be added to a case manually. Choose only ONE
answer.
A. Specimen; Both specimen and task
B. Specimen; Task
C. Both specimen and task; Specimen
D. Task; Both specimen and task Ans✓✓✓ A. Specimen; Both specimen
and task
A surgeon contacts you because she found a typo in all of her patients'
reports in Chart Review. It appears that the heading for Gyn
Interpretation is spelled wrong. In which record will you correct this
mistake? Choose only ONE answer.
A. Test ﴾OVT﴿
B. Result Component ﴾LRR﴿
C. Result Report Template ﴾ETX﴿
D. Result Type ﴾OVG﴿ Ans✓✓✓ B. Result Component ﴾LRR﴿
An HPV DNA test should be ordered automatically when a patient's gyn
interpretation is ASCUS ﴾atypical﴿ and when the provider answers "If
,ASCUS" for the HPV Reflex? order question. With just this information,
how many conditions and components are needed to configure this
reflex action?
Choose ALL answers that apply.
A. 1 condition
B. 2 conditions
C. 1 component
D. 2 components Ans✓✓✓ A. 1 condition
D. 2 components
For which of the following parameters can a default protocol ﴾OVT﴿ be
specified? Choose ALL answers that apply.
A. Source
B. Lab ﴾LDF﴿
C. Rule ﴾CER﴿
D. Procedure ﴾EAP﴿ Ans✓✓✓ A. Source
B. Lab ﴾LDF﴿
C. Rule ﴾CER﴿
If I want a charge code automatically attached to a specimen for the
work I do in the lab, where would I configure this? Choose only ONE
answer.
, A. The General Setup form of the specimen protocol record ﴾OVT﴿.
B. The General Setup form of the task protocol record ﴾OVT﴿.
C. The Task Setup form of the task protocol record ﴾OVT﴿.
D. The Comments form of the specimen protocol record ﴾OVT﴿.
Ans✓✓✓ A. The General Setup form of the specimen protocol record
﴾OVT﴿.
In a task protocol record, the same task is listed on five lines, each with a
different Group. What will happen when I add this task protocol to a
case in Case Builder? Choose only ONE answer.
A. These five tasks will be added to the currently selected block.
B. A new block will be created with all five tasks associated with it.
C. Each task will be associated with a different specimen.
D. Five new blocks will be created, each associated with one task.
Ans✓✓✓ D. Five new blocks will be created, each associated with one
task.
In the procedure category for Lab Pathology Orderables, four allowed
order classes were specified. However, when users order a particular
procedure belonging to that category, there are only three allowed order
classes. Why? Choose only ONE answer.
A. The procedure category ﴾EDP﴿ specified only three allowed order
classes for that particular
order.
with accurate answers
_________ protocols can be linked to test records on the Specialty
Testing form so they are selected by default when users build a case.
________ protocols can be added to a case manually. Choose only ONE
answer.
A. Specimen; Both specimen and task
B. Specimen; Task
C. Both specimen and task; Specimen
D. Task; Both specimen and task Ans✓✓✓ A. Specimen; Both specimen
and task
A surgeon contacts you because she found a typo in all of her patients'
reports in Chart Review. It appears that the heading for Gyn
Interpretation is spelled wrong. In which record will you correct this
mistake? Choose only ONE answer.
A. Test ﴾OVT﴿
B. Result Component ﴾LRR﴿
C. Result Report Template ﴾ETX﴿
D. Result Type ﴾OVG﴿ Ans✓✓✓ B. Result Component ﴾LRR﴿
An HPV DNA test should be ordered automatically when a patient's gyn
interpretation is ASCUS ﴾atypical﴿ and when the provider answers "If
,ASCUS" for the HPV Reflex? order question. With just this information,
how many conditions and components are needed to configure this
reflex action?
Choose ALL answers that apply.
A. 1 condition
B. 2 conditions
C. 1 component
D. 2 components Ans✓✓✓ A. 1 condition
D. 2 components
For which of the following parameters can a default protocol ﴾OVT﴿ be
specified? Choose ALL answers that apply.
A. Source
B. Lab ﴾LDF﴿
C. Rule ﴾CER﴿
D. Procedure ﴾EAP﴿ Ans✓✓✓ A. Source
B. Lab ﴾LDF﴿
C. Rule ﴾CER﴿
If I want a charge code automatically attached to a specimen for the
work I do in the lab, where would I configure this? Choose only ONE
answer.
, A. The General Setup form of the specimen protocol record ﴾OVT﴿.
B. The General Setup form of the task protocol record ﴾OVT﴿.
C. The Task Setup form of the task protocol record ﴾OVT﴿.
D. The Comments form of the specimen protocol record ﴾OVT﴿.
Ans✓✓✓ A. The General Setup form of the specimen protocol record
﴾OVT﴿.
In a task protocol record, the same task is listed on five lines, each with a
different Group. What will happen when I add this task protocol to a
case in Case Builder? Choose only ONE answer.
A. These five tasks will be added to the currently selected block.
B. A new block will be created with all five tasks associated with it.
C. Each task will be associated with a different specimen.
D. Five new blocks will be created, each associated with one task.
Ans✓✓✓ D. Five new blocks will be created, each associated with one
task.
In the procedure category for Lab Pathology Orderables, four allowed
order classes were specified. However, when users order a particular
procedure belonging to that category, there are only three allowed order
classes. Why? Choose only ONE answer.
A. The procedure category ﴾EDP﴿ specified only three allowed order
classes for that particular
order.
