Verified Answers Graded A
FINE-C - ANSWER -FINE-C refers to an Do not use the throttle if the choke is On as this
engine pre-start routine. It stands for Fuel, could provide too much fuel to the engine.
Ignition, Neutral, Engine cut-off switch, Choke
and Clutch. Once the engine is started, you can release the
clutch lever, but do so slowly in case the
motorcycle is not in neutral.
F- ANSWER -Fuel, means if equipped, Some engines will not start if the side stand is
turn the fuel supply valve On. down. Many motorcycles will allow the engine to
start but will stall when the motorcycle is shifted
into gear when the side stand is down.
I- ANSWER -Ignition, means turn the
ignition switch to the On position. Some indicator
lights should come on. Engine stop procedure - ANSWER -To stop
the engine:
First, move the engine cut-off switch to Off with
your right thumb. Do this every time so you can
N- ANSWER -Neutral, means to be in
develop the habit in case you need to shut off the
Neutral. The green light in the instrument cluster
engine in an emergency.
"indicates" neutral. When in neutral, the
motorcycle will roll forward and backward with
Turn the ignition switch to Off.
the clutch lever and front brake lever released.
Turn the fuel supply valve Off if it has that
position.
E- ANSWER -Engine cut-off switch means It may help to remember the Engine Stop
put the switch in the Run/On position. Procedure as Thumb, Key, Valve.
C- ANSWER -Choke and Clutch, means to Clutch Lever & Friction Zone - ANSWER -
set the choke and squeeze in the clutch lever. Proper use of the clutch lever and friction zone is
The choke should be On for a cold engine, critical for starting out smoothly and slow speed
although some motorcycles do not have a choke. maneuvers.
The friction zone is a small area in the travel of
the clutch lever that controls the connection
between the engine and the rear wheel. Fully
Engine start procedure - ANSWER -When squeezing in the clutch lever removes power
starting the engine: Apply at least one of the from the rear wheel.
brakes.
The video shown here illustrates how clutch-lever
Squeeze in the clutch lever fully. use connects power to the rear wheel. Notice
Press the starter button. squeezing the clutch lever removes power from
the rear wheel.
1/6
, MSF Basic eCourse: About Basic Operation Test Questions with
Verified Answers Graded A
direction by first pressing the handgrip on the
If you lose control of the motorcycle and want to same side of the intended turn. This is called
stop, you should squeeze in the clutch lever fully countersteering because the handlebars are
and use the brakes as needed. initially moved opposite the direction of the turn.
Riding Posture - ANSWER -Good posture Basic Steps for Turning - ANSWER -As you
helps you control the motorcycle. Keep your: learn the skills needed to change direction, you
want to consider:
Back straight and head and eyes up Speed
Where to look
Feet on the footrests and near the controls Handgrip pressure to move the handlebars
Throttle use
Knees and elbows comfortably in
Arms relaxed and bent Think about it in this order:
Slow
Fingers around the throttle with your wrist flat Look
Press
As you are learning to ride, it may be helpful to Roll
keep the fingers of your left hand over the clutch These steps provide a basic procedure for
lever—cover the clutch lever. This is so you can learning to make turns.
readily remove power from the rear wheel and
stop.
Basic Turning: Step 1 - ANSWER -Slow
means to have a safe entry speed that doesn't
Turns-Corners-Curves - ANSWER -Like require slowing after entering the turn. For most
riding a bicycle, a motorcycle requires you to corners, this means to roll off the throttle and use
balance. Steering a motorcycle involves proper the brakes before the turn. Reduce speed if
use of the handlebars. Because a motorcycle is needed before entering a turn by rolling off the
heavier and more powerful than a bicycle, it is throttle and using the brakes as needed.
important to learn to turn well.
Sometimes downshifting to a lower gear is
Whether called a turn, corner, or curve, changing necessary, and this should be done before the
direction requires special attention. turn begins. You want to set up for the turn by
having a safe entry speed. A safe entry speed is
the speed at the beginning of the turn that allows
you to maintain or increase speed while in the
Turns-Corners-Curves, Cont. - ANSWER - turn.
When riding a motorcycle at very low speed, like
walking speed, change direction by leaning the
motorcycle and turning the handlebars in the
direction you want to go. Basic Turning: Step 2 - ANSWER -The next
step, Look, means to keep your eyes up and
At higher speeds, you initiate a change of looking throughout the turn. As you approach a
2/6