G3 TEST 2025
1. According to the workplace safety and insurance board act, which of the following
statements is part of the workers obligation in all cases of injury and or disease.
A) obtain first aid promptly
B) notify the employer of any injury within eight hours
C) notify the employer of the possible onset of a work related disease/condition within
two working days
D) find a doctor or qualified practitioner who will give a second opinion concerning the
injury. - CORRECT ANSWER-B) notify the employer of any injury within eight hours
Which of the following statements is true?
A) workers do not have to wear hard hats on a job site, even if instructed not to do so by
employer
B) workers must wear the protective clothing that the employer instructs them to wear
on the job site
C) workers do not have to be aware of the contents of the occupational health and
safety act.
D) unnecessary running or rough or boisterous conduct on job sites is NOT prohibited
by the occupational health and safety actoisterous conduct on job sites is NOT
prohibited by the occupational health and safety act - CORRECT ANSWER-B) workers
must wear the protective clothing that the employer instructs them to wear on the job
site.
3. Which of the following is true:
A) when lifting, it is best to use your back muscles as they are the strongest
B) when lifting, it is best to lift by bending your knees and using your leg muscles
C) when lifting a heavy load that is too heavy, lift and carry it short distances at a time.
D) none of these statements apply - CORRECT ANSWER-B) when lifting, it is best to lift
by bending your knees and using your leg muscles
Which of the following lists best describes the key safety categories which should be
considered by a fuel technician in Ontario:
A) personal safety, site, tools, equipment, safety of others, OHSA, deadlines
,B) personal safety, tools, equipment, safety of others, deadlines, Ontario fuel code
requirements
C) personal safety, tools, equipment, safety of others, site, OHSA, Ontario fuel codes
D) personal safety, tools, equipment, safety of others, Ontario fuel codes - CORRECT
ANSWER-C) personal safety, tools, equipment, safety of others, site, OHSA, Ontario
fuel codes
5. How often do portable fire extinguishers have to be inspected?
A) every month
B) every six months
C) every nine months
D) every twelve months - CORRECT ANSWER-D) every twelve months
6. What does OSHA stand for?
A) Ontario health and standards act
B) Ontario health and safety act
C) occupational health and safety act
D) occupational health and standard ac - CORRECT ANSWER-C) occupational health
and safety act
7. Technicians use MSDS sheets to:
A) be aware of flammable,corrosive, or explosive substances
B) know what materials are available for the technicians use
C) know the best brand of product to purchase
D) be aware of the best source of lubricants for machinery on site - CORRECT
ANSWER-A) be aware of flammable,corrosive, or explosive substances
8.Which of the following phrases is true:
A). the natural gas and propane installation code requires a technician to report a
hazardous installation within three working days of completion
B) the OSHA requires that hazards be reported within 72 hours
C) the industry does not demand that hazards be reported for correction
D) the hazard is the responsibility of the person who is aware of it - CORRECT
ANSWER-D) the hazard is the responsibility of the person who is aware of it
9. Why should garbage and debris be removed from a job site:
A) to present a neat appearance
B) to prevent possible slips, trips or falls
C) to reduce the possibility of tool loss in debris
D) to reduce the likelihood of rodents on the job site - CORRECT ANSWER-B) to
prevent possible slips, trips or falls
10. What should a fuel technician do when a new piece of equipment is introduced for
use:
A) carefully examine the equipment and determine how to use it properly
B) ask the appliance owner to help determine how to use it properly
, C) get a copy of the user's manual and read it before using the equipment
D) refuse to work with new equipment until someone else has used it. - CORRECT
ANSWER-C) get a copy of the user's manual and read it before using the equipment
11. Copper wire should be skinned with:
A) knife
B) pliers
C) side cutters
D) a wire stripper - CORRECT ANSWER-D) a wire stripper
12. What is the volume of a room measuring 16'X12'X7'
A) 84 square feet
B) 192 cubic feet
C) 1344 cubic feet
D) 16, 128 square feet - CORRECT ANSWER-C) 1344 cubic feet
13. What is purpose of a drill gauge:
A) to measure the diameter of a drill bit
B) to measure the diameter of a drill
C) to measure the length of a drill
D) to measure the length of a drill bit - CORRECT ANSWER-A) to measure the
diameter of a drill bit
14.The fastener used to connect a drain hose to a fan coil unit is:
A) a gear clamp
B) copper bailing wire
C) electrical tape
D) grappler bar - CORRECT ANSWER-A) a gear clamp
15. What is the area of rectangular air supply opening measuring 12"x10"
A) 1.0 square feet
B) 1.2 cubic feet
C) 100 cubic inches
D) 120 square inches - CORRECT ANSWER-D) 120 square inches
16. How should an electric drill be disconnected:
A) by pulling on the drills cord
B) by pulling the plug at the outlet
C) by using a pair of insulated channel lock pliers
D) with the chuck key. - CORRECT ANSWER-B) by pulling the plug at the outlet
17. A foot has inches ____and a meter has____centinmeters.
A) 12 inches,100 centimeters
B) 10 inches, l00 centimeters
C) 100 inches,12 centimeters
D) l0 inches, l00 centimeter - CORRECT ANSWER-A) 12 inches,100 centimeters
1. According to the workplace safety and insurance board act, which of the following
statements is part of the workers obligation in all cases of injury and or disease.
A) obtain first aid promptly
B) notify the employer of any injury within eight hours
C) notify the employer of the possible onset of a work related disease/condition within
two working days
D) find a doctor or qualified practitioner who will give a second opinion concerning the
injury. - CORRECT ANSWER-B) notify the employer of any injury within eight hours
Which of the following statements is true?
A) workers do not have to wear hard hats on a job site, even if instructed not to do so by
employer
B) workers must wear the protective clothing that the employer instructs them to wear
on the job site
C) workers do not have to be aware of the contents of the occupational health and
safety act.
D) unnecessary running or rough or boisterous conduct on job sites is NOT prohibited
by the occupational health and safety actoisterous conduct on job sites is NOT
prohibited by the occupational health and safety act - CORRECT ANSWER-B) workers
must wear the protective clothing that the employer instructs them to wear on the job
site.
3. Which of the following is true:
A) when lifting, it is best to use your back muscles as they are the strongest
B) when lifting, it is best to lift by bending your knees and using your leg muscles
C) when lifting a heavy load that is too heavy, lift and carry it short distances at a time.
D) none of these statements apply - CORRECT ANSWER-B) when lifting, it is best to lift
by bending your knees and using your leg muscles
Which of the following lists best describes the key safety categories which should be
considered by a fuel technician in Ontario:
A) personal safety, site, tools, equipment, safety of others, OHSA, deadlines
,B) personal safety, tools, equipment, safety of others, deadlines, Ontario fuel code
requirements
C) personal safety, tools, equipment, safety of others, site, OHSA, Ontario fuel codes
D) personal safety, tools, equipment, safety of others, Ontario fuel codes - CORRECT
ANSWER-C) personal safety, tools, equipment, safety of others, site, OHSA, Ontario
fuel codes
5. How often do portable fire extinguishers have to be inspected?
A) every month
B) every six months
C) every nine months
D) every twelve months - CORRECT ANSWER-D) every twelve months
6. What does OSHA stand for?
A) Ontario health and standards act
B) Ontario health and safety act
C) occupational health and safety act
D) occupational health and standard ac - CORRECT ANSWER-C) occupational health
and safety act
7. Technicians use MSDS sheets to:
A) be aware of flammable,corrosive, or explosive substances
B) know what materials are available for the technicians use
C) know the best brand of product to purchase
D) be aware of the best source of lubricants for machinery on site - CORRECT
ANSWER-A) be aware of flammable,corrosive, or explosive substances
8.Which of the following phrases is true:
A). the natural gas and propane installation code requires a technician to report a
hazardous installation within three working days of completion
B) the OSHA requires that hazards be reported within 72 hours
C) the industry does not demand that hazards be reported for correction
D) the hazard is the responsibility of the person who is aware of it - CORRECT
ANSWER-D) the hazard is the responsibility of the person who is aware of it
9. Why should garbage and debris be removed from a job site:
A) to present a neat appearance
B) to prevent possible slips, trips or falls
C) to reduce the possibility of tool loss in debris
D) to reduce the likelihood of rodents on the job site - CORRECT ANSWER-B) to
prevent possible slips, trips or falls
10. What should a fuel technician do when a new piece of equipment is introduced for
use:
A) carefully examine the equipment and determine how to use it properly
B) ask the appliance owner to help determine how to use it properly
, C) get a copy of the user's manual and read it before using the equipment
D) refuse to work with new equipment until someone else has used it. - CORRECT
ANSWER-C) get a copy of the user's manual and read it before using the equipment
11. Copper wire should be skinned with:
A) knife
B) pliers
C) side cutters
D) a wire stripper - CORRECT ANSWER-D) a wire stripper
12. What is the volume of a room measuring 16'X12'X7'
A) 84 square feet
B) 192 cubic feet
C) 1344 cubic feet
D) 16, 128 square feet - CORRECT ANSWER-C) 1344 cubic feet
13. What is purpose of a drill gauge:
A) to measure the diameter of a drill bit
B) to measure the diameter of a drill
C) to measure the length of a drill
D) to measure the length of a drill bit - CORRECT ANSWER-A) to measure the
diameter of a drill bit
14.The fastener used to connect a drain hose to a fan coil unit is:
A) a gear clamp
B) copper bailing wire
C) electrical tape
D) grappler bar - CORRECT ANSWER-A) a gear clamp
15. What is the area of rectangular air supply opening measuring 12"x10"
A) 1.0 square feet
B) 1.2 cubic feet
C) 100 cubic inches
D) 120 square inches - CORRECT ANSWER-D) 120 square inches
16. How should an electric drill be disconnected:
A) by pulling on the drills cord
B) by pulling the plug at the outlet
C) by using a pair of insulated channel lock pliers
D) with the chuck key. - CORRECT ANSWER-B) by pulling the plug at the outlet
17. A foot has inches ____and a meter has____centinmeters.
A) 12 inches,100 centimeters
B) 10 inches, l00 centimeters
C) 100 inches,12 centimeters
D) l0 inches, l00 centimeter - CORRECT ANSWER-A) 12 inches,100 centimeters