TCFP Inspector's Class Study Guide.
1. Which duty is not the responsibility of a level I B) American
Inspec- tor? National
A) Handle citizen complaints related to fire Standards
Institute
and life safety.
B) Perform plans reviews.
C)Interpret and apply adopted codes and
standards.
D) Determine occupancy loads for single-use
build- ings.
2. Most of the consensus standards that relate to
fire and life safety are developed by the
following organi- zations except:
ASTM International,
National Fire Protection Assoc.,
American National Standards
Institute, Underwriters Laboratories
3. Regarding Commercial Kitchen Hood Systems,
pipe penetrations of the exhaust hood
require what?
a. Minimum 18 inch clearance to combustible
materi- als
b. Printed manufacturer guidelines of spacing
on the pipe itself
c. Gas shut off valve and electrical shunt
accessibility
d. A liquid tight continuous external weld
4. A independent, non-profit organization that
tests products for their intended use and
certifies them as safe describes:
A) ASTM International
, TCFP Inspector's Class Study Guide.
Perform plans reviews.
American National Stan- dards Institute
A liquid tight continuous external weld
Underwriters Laboratories Inc.
, TCFP Inspector's Class Study Guide.
C)Underwriters Laboratories Inc.
D) Standards Council of Canada
5. Which is not one of the three general types of drawings Aerial view
used to show structure, facility, or site information?
A. Plot plan
B. Aerial view
C. Floor plan
D. Elevation view
6. Structural lumber has a moisture 19%
content of
% or
less. 25%
19%
15%
12%
7. Which of the following occupancies does not fall under Post oflce
state and local regulations?
A).Day care
B). Jail
C).Post office
D).Medical facility
8. The typical life cycle of a model code 3-5
edition is
years.
a. 5-7
b. 2-3
c. 7-10
d. 3-5
, TCFP Inspector's Class Study Guide.
9. For Dry systems exceeding 500 gallons, there must be Not more than
60 seconds
a quick opening device installed unless water is deliv-
1. Which duty is not the responsibility of a level I B) American
Inspec- tor? National
A) Handle citizen complaints related to fire Standards
Institute
and life safety.
B) Perform plans reviews.
C)Interpret and apply adopted codes and
standards.
D) Determine occupancy loads for single-use
build- ings.
2. Most of the consensus standards that relate to
fire and life safety are developed by the
following organi- zations except:
ASTM International,
National Fire Protection Assoc.,
American National Standards
Institute, Underwriters Laboratories
3. Regarding Commercial Kitchen Hood Systems,
pipe penetrations of the exhaust hood
require what?
a. Minimum 18 inch clearance to combustible
materi- als
b. Printed manufacturer guidelines of spacing
on the pipe itself
c. Gas shut off valve and electrical shunt
accessibility
d. A liquid tight continuous external weld
4. A independent, non-profit organization that
tests products for their intended use and
certifies them as safe describes:
A) ASTM International
, TCFP Inspector's Class Study Guide.
Perform plans reviews.
American National Stan- dards Institute
A liquid tight continuous external weld
Underwriters Laboratories Inc.
, TCFP Inspector's Class Study Guide.
C)Underwriters Laboratories Inc.
D) Standards Council of Canada
5. Which is not one of the three general types of drawings Aerial view
used to show structure, facility, or site information?
A. Plot plan
B. Aerial view
C. Floor plan
D. Elevation view
6. Structural lumber has a moisture 19%
content of
% or
less. 25%
19%
15%
12%
7. Which of the following occupancies does not fall under Post oflce
state and local regulations?
A).Day care
B). Jail
C).Post office
D).Medical facility
8. The typical life cycle of a model code 3-5
edition is
years.
a. 5-7
b. 2-3
c. 7-10
d. 3-5
, TCFP Inspector's Class Study Guide.
9. For Dry systems exceeding 500 gallons, there must be Not more than
60 seconds
a quick opening device installed unless water is deliv-
