MKC Study Guide Questions and Answers
Q: WHAT SECTION OF CCM IS BECCE'S UNDER?
✓✓ 2
Q: WHAT CAUSES A BOILER WITH FUEL GUN INJECTOR
TO PULSATE?
✓✓ PRESSURIZED COMBUSTION CHAMBER
Q: WHO IS CONVENING AUTHORITY FOR HULL BOARD
ON CUTTERS IN CG YARDS?
✓✓ NESU
Q: PURPOSE OF VANE ON OUTBOARD PISTON?
✓✓ ALLOW CROSS FLOW
Q: WHAT AMOUNT OF PSI IS DECREASED BY EACH
COMPRESSION RING ON A PISTON?
✓✓ 1/2 THE PSI ABOVE THE RING
Q: OUTBOARD ENGINE TURNS EASY TO PORT, ADJUST
TRIM TAB?
✓✓ TO STBD
,Q: IF BOILER MAKE UP FEED WATER HAS A TDS
READING OF 500 PPM, WHAT IS ALLOWABLE UPPER
LIMIT?
✓✓ 1000 PPM
Q: SHELF LIFE FOR BROMINE CARTRIDGE?
✓✓ 2 YEARS
Q: THRUST BEARING SHOES ARE WORN AND NO
SPARES?
✓✓ SHIFT AHEAD WITH ASTERN
Q: THRUST BEARING COLLAR IS SCORED?
✓✓ RESURFACE
Q: MAIN SPACE FIRE OUT OF CONTROL, EVAC ALL
PERSONNEL AND SET VENTILATION TO?
✓✓ VENTILATION WILL BE SECURED
Q: ORDERING PRECUT HYDRAULIC HOSE WITH NUMBER
1706-10-0144, HOW LONG IS HOSE?
✓✓ 14 4/8"
Q: WHAT IS USED TO CLEAN ENDS OF TUBING?
✓✓ WIRE BRUSH AND SANDPAPER
,Q: A 10 PSI RISE IN A/C SYSTEM AFTER EVACUATION IS
AN INDICATION OF?
✓✓ LEAK
Q: HOW LONG WILL AN AUXILIARY BOILER HAVE TO BE
SECURED BEFORE DOING BLOW DOWNS?
✓✓ 2 HRS
Q: WHERE DO YOU FIND INFO FOR RETENTION OR
DISPOSAL OF ENGINEERING LOGS?
✓✓ PAPERWORK MANAGEMENT MANUAL
Q: IF YOU FIND SOMETHING ON YOUR VESSEL NOT
LISTED IN CALMS, WHERE DO YOU LOOK FOR
SUBMITTING INFO?
✓✓ SUPPLY POLICY AND PROCEDURES MANUAL
Q: WHERE DO YOU FIND THE PROPER NUMBER WHEN
DRAFTING CASUALTY CONTROL PROCEDURES?
✓✓ NAVAL FLEET MOBILITY EXERCISES MAN
Q: FOR FILLING AND BALLASTING F/O TANKS, SEE WHAT
BILL?
✓✓ F/O TRANSFER AND BALLAST BILL
, Q: TO USE AEL F/O TEST KIT, FOLLOW THE
INSTRUCTIONS FROM?
✓✓ MFG
Q: WHAT PART OF DRILL PRESS IS THE QUILL?
✓✓ THE PART THAT LIMITS THE TOOL TRAVEL
Q: WHO HAS TO GIVE PERMISSION TO TRANSFER
LIQUIDS WHILE IN DRYDOCK?
✓✓ DOCKMASTER
Q: WHAT IS UNACCEPTABLE LIMIT FOR GO NO GO
GAUGE ON JP-5 SYSTEM? (THE PSI DIFFERENCE ACROSS
FILTER/STRAINER)?
✓✓ 20 PSI
Q: WHAT SENSES OIL IN THE 10 GPM OWS?
✓✓ PROBE
Q: FIRST THING TO DO IF A 100 GPM OWS HAS A 40 PSI
READING?
✓✓ CHANGE ELEMENTS
Q: INFLATE SHAFT SEALS TO A MAXIMUM OF?
✓✓ 125 PSI
Q: WHAT SECTION OF CCM IS BECCE'S UNDER?
✓✓ 2
Q: WHAT CAUSES A BOILER WITH FUEL GUN INJECTOR
TO PULSATE?
✓✓ PRESSURIZED COMBUSTION CHAMBER
Q: WHO IS CONVENING AUTHORITY FOR HULL BOARD
ON CUTTERS IN CG YARDS?
✓✓ NESU
Q: PURPOSE OF VANE ON OUTBOARD PISTON?
✓✓ ALLOW CROSS FLOW
Q: WHAT AMOUNT OF PSI IS DECREASED BY EACH
COMPRESSION RING ON A PISTON?
✓✓ 1/2 THE PSI ABOVE THE RING
Q: OUTBOARD ENGINE TURNS EASY TO PORT, ADJUST
TRIM TAB?
✓✓ TO STBD
,Q: IF BOILER MAKE UP FEED WATER HAS A TDS
READING OF 500 PPM, WHAT IS ALLOWABLE UPPER
LIMIT?
✓✓ 1000 PPM
Q: SHELF LIFE FOR BROMINE CARTRIDGE?
✓✓ 2 YEARS
Q: THRUST BEARING SHOES ARE WORN AND NO
SPARES?
✓✓ SHIFT AHEAD WITH ASTERN
Q: THRUST BEARING COLLAR IS SCORED?
✓✓ RESURFACE
Q: MAIN SPACE FIRE OUT OF CONTROL, EVAC ALL
PERSONNEL AND SET VENTILATION TO?
✓✓ VENTILATION WILL BE SECURED
Q: ORDERING PRECUT HYDRAULIC HOSE WITH NUMBER
1706-10-0144, HOW LONG IS HOSE?
✓✓ 14 4/8"
Q: WHAT IS USED TO CLEAN ENDS OF TUBING?
✓✓ WIRE BRUSH AND SANDPAPER
,Q: A 10 PSI RISE IN A/C SYSTEM AFTER EVACUATION IS
AN INDICATION OF?
✓✓ LEAK
Q: HOW LONG WILL AN AUXILIARY BOILER HAVE TO BE
SECURED BEFORE DOING BLOW DOWNS?
✓✓ 2 HRS
Q: WHERE DO YOU FIND INFO FOR RETENTION OR
DISPOSAL OF ENGINEERING LOGS?
✓✓ PAPERWORK MANAGEMENT MANUAL
Q: IF YOU FIND SOMETHING ON YOUR VESSEL NOT
LISTED IN CALMS, WHERE DO YOU LOOK FOR
SUBMITTING INFO?
✓✓ SUPPLY POLICY AND PROCEDURES MANUAL
Q: WHERE DO YOU FIND THE PROPER NUMBER WHEN
DRAFTING CASUALTY CONTROL PROCEDURES?
✓✓ NAVAL FLEET MOBILITY EXERCISES MAN
Q: FOR FILLING AND BALLASTING F/O TANKS, SEE WHAT
BILL?
✓✓ F/O TRANSFER AND BALLAST BILL
, Q: TO USE AEL F/O TEST KIT, FOLLOW THE
INSTRUCTIONS FROM?
✓✓ MFG
Q: WHAT PART OF DRILL PRESS IS THE QUILL?
✓✓ THE PART THAT LIMITS THE TOOL TRAVEL
Q: WHO HAS TO GIVE PERMISSION TO TRANSFER
LIQUIDS WHILE IN DRYDOCK?
✓✓ DOCKMASTER
Q: WHAT IS UNACCEPTABLE LIMIT FOR GO NO GO
GAUGE ON JP-5 SYSTEM? (THE PSI DIFFERENCE ACROSS
FILTER/STRAINER)?
✓✓ 20 PSI
Q: WHAT SENSES OIL IN THE 10 GPM OWS?
✓✓ PROBE
Q: FIRST THING TO DO IF A 100 GPM OWS HAS A 40 PSI
READING?
✓✓ CHANGE ELEMENTS
Q: INFLATE SHAFT SEALS TO A MAXIMUM OF?
✓✓ 125 PSI
