MEC 316 EXAM WITH
CORRECT SOLUTION
What are the advantages of wind power? - ANSWER + sustainable energy
+ clean energy
+ no fuel transportation or storage
+ free source
+ spatial dispersion of energy
What are the disadvantages of wind turbines? - ANSWER - unpredictable
- cost of turbine (integration and installation)
- environmental impact (visual, noise, wildlife, radio interference)
Explain the effects of the atmospheric boundary layer on wind power generation. -
ANSWER wind speed increases with height in atmospheric boundary layer
What is the boundary layer power law? - ANSWER (Uz/U10) = (Z/10)^a
where Uz and U10 are velocities at heights Z, 10 metres respectively.
a=0.15 for level grass with scattered trees, for rougher surfaces a>0.15
What is the Weibull distribution? - ANSWER H = 8760 exp[-(V/C)^k]
H=hours/years during which V is exceeded
V = annual average wind speed
typically k=2, C=1.13V
What are the non-dimensional parameters that affect the wind turbine power
coefficient? - ANSWER power coefficient, tip speed ratio, solidity, Reynolds number.
Power Coefficient (Cp) equation - ANSWER =power extracted from wind / power
available in wind = P/E
Tip speed ratio - ANSWER = blade tip speed / wind speed
solidity - ANSWER = total blade area/ flow area swept by rotor
,Reynolds number - ANSWER
What are the main difference of HAWTs and VAWTs? - ANSWER -HAWTs face wind,
VAWTs can use wind from any direction
-HAWTs more common
-HAWTs have rotor, gearbox etc at top, VAWTs don't
-VAWTs used in urban environments
-HAWTs used under streamline wind conditions
Give some examples of HAWTs. - ANSWER 1. high solidity, low speed:
-max running time more important than max power
-e.g. american traditional, wind pumps, windmills
2. low solidity/high speed
-look like aircraft propellers
-most popular
-max power per unit cost desired
-single,two or three -bladed
Give some examples of VAWTs. - ANSWER -aerofoil blades
-Darrius/ Troposkein arc blades
-fixed straight blades H-type wind turbine
Give an example of drag type wind turbines - ANSWER cup anemometer and savonius
wind turbine
What are the advantages of VAWT? - ANSWER + generator, gearbox etc can be on the
ground (easier to maintain)
+don't need yaw mechanism and control system to turn rotor against the wind, operates
from any direction
+manufacturing cost lower
What are the disadvantages of VAWTs? - ANSWER -oscillatory forces can cause
vibration damage or fatigue
-not self-starting
-needs wires, can be impractical
, -blade optimisation more challenging due to unsteady condition
-VAWTs are very difficult to mount high on a tower to capture the higher level winds. so
use lower, more turbulent winds and produce less in possibly more damaging winds.
What is the theoretical upper limit of the energy that a wind turbine can extract from the
kinetic energy in the wind. - ANSWER 59.3%
Betz limit - ANSWER
Betz limit assumptions - ANSWER -homogeneous, incompressible, steady state flow
-flow uni-directional
-inviscid flow
-infinite number of blades represented by a disc
-uniform thrust over disc of rotor area
-rotor only (no hub or tower effects)
An empirical formula, E = 2.5 A (V_m ^3) , can be used to make a rough estimate of the
annual electricity production in kWh. why is this different to the Betz limit? - ANSWER (1)
The Betz limit is a theoretical upper limit for wind turbines. It is normally less than 50%
for operational wind turbines;
(2) The turbine availability is normally about 90% rather than 100% as assumed in the
empirical formula.
Why is a drag-type VAWT not desirable for harvesting wind energy? - ANSWER -very low
efficiency
-maximum Cp only 11% for drag-type
Why is the performance of a drag-type VAWT much lower than lift-type WTs? - ANSWER
shape affects drag, aerofoil has much lower drag coefficient
Describe the process of blade stall in relation to aerofoil dynamics - ANSWER stall is
caused by boundary layer separation, occurs when flow suddenly leaves the suction
side of the aerofoil (when the angle of attack becomes too large).
causes loss in lift and increase in drag. dangerous in planes but good in WTs.
Why is stall angle an important factor in wind turbine blade design? - ANSWER -limiting
the performance at high lift/ wind conditions
-can be used to control the rotor speed.
Which span section of the HAWT blade works hardest in extracting energy from the
wind? - ANSWER the outboard blade (force generated is much higher for the blade
CORRECT SOLUTION
What are the advantages of wind power? - ANSWER + sustainable energy
+ clean energy
+ no fuel transportation or storage
+ free source
+ spatial dispersion of energy
What are the disadvantages of wind turbines? - ANSWER - unpredictable
- cost of turbine (integration and installation)
- environmental impact (visual, noise, wildlife, radio interference)
Explain the effects of the atmospheric boundary layer on wind power generation. -
ANSWER wind speed increases with height in atmospheric boundary layer
What is the boundary layer power law? - ANSWER (Uz/U10) = (Z/10)^a
where Uz and U10 are velocities at heights Z, 10 metres respectively.
a=0.15 for level grass with scattered trees, for rougher surfaces a>0.15
What is the Weibull distribution? - ANSWER H = 8760 exp[-(V/C)^k]
H=hours/years during which V is exceeded
V = annual average wind speed
typically k=2, C=1.13V
What are the non-dimensional parameters that affect the wind turbine power
coefficient? - ANSWER power coefficient, tip speed ratio, solidity, Reynolds number.
Power Coefficient (Cp) equation - ANSWER =power extracted from wind / power
available in wind = P/E
Tip speed ratio - ANSWER = blade tip speed / wind speed
solidity - ANSWER = total blade area/ flow area swept by rotor
,Reynolds number - ANSWER
What are the main difference of HAWTs and VAWTs? - ANSWER -HAWTs face wind,
VAWTs can use wind from any direction
-HAWTs more common
-HAWTs have rotor, gearbox etc at top, VAWTs don't
-VAWTs used in urban environments
-HAWTs used under streamline wind conditions
Give some examples of HAWTs. - ANSWER 1. high solidity, low speed:
-max running time more important than max power
-e.g. american traditional, wind pumps, windmills
2. low solidity/high speed
-look like aircraft propellers
-most popular
-max power per unit cost desired
-single,two or three -bladed
Give some examples of VAWTs. - ANSWER -aerofoil blades
-Darrius/ Troposkein arc blades
-fixed straight blades H-type wind turbine
Give an example of drag type wind turbines - ANSWER cup anemometer and savonius
wind turbine
What are the advantages of VAWT? - ANSWER + generator, gearbox etc can be on the
ground (easier to maintain)
+don't need yaw mechanism and control system to turn rotor against the wind, operates
from any direction
+manufacturing cost lower
What are the disadvantages of VAWTs? - ANSWER -oscillatory forces can cause
vibration damage or fatigue
-not self-starting
-needs wires, can be impractical
, -blade optimisation more challenging due to unsteady condition
-VAWTs are very difficult to mount high on a tower to capture the higher level winds. so
use lower, more turbulent winds and produce less in possibly more damaging winds.
What is the theoretical upper limit of the energy that a wind turbine can extract from the
kinetic energy in the wind. - ANSWER 59.3%
Betz limit - ANSWER
Betz limit assumptions - ANSWER -homogeneous, incompressible, steady state flow
-flow uni-directional
-inviscid flow
-infinite number of blades represented by a disc
-uniform thrust over disc of rotor area
-rotor only (no hub or tower effects)
An empirical formula, E = 2.5 A (V_m ^3) , can be used to make a rough estimate of the
annual electricity production in kWh. why is this different to the Betz limit? - ANSWER (1)
The Betz limit is a theoretical upper limit for wind turbines. It is normally less than 50%
for operational wind turbines;
(2) The turbine availability is normally about 90% rather than 100% as assumed in the
empirical formula.
Why is a drag-type VAWT not desirable for harvesting wind energy? - ANSWER -very low
efficiency
-maximum Cp only 11% for drag-type
Why is the performance of a drag-type VAWT much lower than lift-type WTs? - ANSWER
shape affects drag, aerofoil has much lower drag coefficient
Describe the process of blade stall in relation to aerofoil dynamics - ANSWER stall is
caused by boundary layer separation, occurs when flow suddenly leaves the suction
side of the aerofoil (when the angle of attack becomes too large).
causes loss in lift and increase in drag. dangerous in planes but good in WTs.
Why is stall angle an important factor in wind turbine blade design? - ANSWER -limiting
the performance at high lift/ wind conditions
-can be used to control the rotor speed.
Which span section of the HAWT blade works hardest in extracting energy from the
wind? - ANSWER the outboard blade (force generated is much higher for the blade