1|Pag e
BPI BUILDING ANALYST EXAM|| LATELY
UPDATED QUESTIONS AND 100% CORRECT
ANSWERS ALREADY GRADED A+|| LATEST AND
COMPLETE VERSION 2024-2025 WITH VERIFIED
SOLUTIONS|| ASSURED PASS!!!!
which is not one of the four primary ways moisture moves through buildings?
-capillary seepage
-humidity
-air movement
-vapor diffusion - ANSWER: humidity
a combustion appliance fails spillage if it spills flue gasses for ___ seconds?
-90
-60
-30
-120 - ANSWER: 120
what establishes the R-value ratings for windows and doors? - ANSWER: NFRC
where should the test hole be drilled for determining draft on appliances? -
ANSWER: 1'-2' downstream of the appliance draft diverter
what is the R-value of a window with a U factor of 0.25?
-2
-3
-1
,2|Pag e
-4 - ANSWER: 4
according to BPI standards, what must be kept on each crew vehicle and made
available to all workers and clients upon request? - ANSWER: Material Safety
Data Sheet
according to the BPI standards, what is the CAZ depressurization limit for an
orphaned natural draft water heater?
- -2cfm
- -2 pa
- -5cfm
- -5 pa - ANSWER: -2 pa
if wood is placed in wet soil, what moisture gradient will occur? - ANSWER: the
wetness of the soil will move into the wood
what does the blower door test evaluate? - ANSWER: air leakage level of the
building
according to ASHRAE, homes should receive at least __ air changes per hour or __
cfm per person - ANSWER: 0.35, 15
asbestos is a "known carcinogen" found in all of the following except?
-siding
-steam-pipe insulation
-floor tiles
-windows - ANSWER: windows
, 3|Pag e
digital readouts for carbon monoxide tests are given in:
-cubic inches per minute (CIM)
-cubic feet per minute (CFM)
-parts per million (PPM)
-inches of water column (IWC) - ANSWER: cubic feet per minute (CFM)
the first step when conducting a combustion appliance zone test is to:
-establish worst case
-measure the worst case spillage
-measure the base pressure
-action levels - ANSWER: measure the base pressure
the combination of air temperature, radiant temperature, humidity, and air
movement determine - ANSWER: comfort
what is not a sign flexible gas lines need to be replaced?
-if they're kinked
-if they're corroded
-if they're made of a silicone material
-if the line was manufactured before 1973 - ANSWER: if they're made of a
silicone material
why is window replacement usually not among the most cost-effective retrofits? -
ANSWER: new windows are expensive to buy and install
BPI BUILDING ANALYST EXAM|| LATELY
UPDATED QUESTIONS AND 100% CORRECT
ANSWERS ALREADY GRADED A+|| LATEST AND
COMPLETE VERSION 2024-2025 WITH VERIFIED
SOLUTIONS|| ASSURED PASS!!!!
which is not one of the four primary ways moisture moves through buildings?
-capillary seepage
-humidity
-air movement
-vapor diffusion - ANSWER: humidity
a combustion appliance fails spillage if it spills flue gasses for ___ seconds?
-90
-60
-30
-120 - ANSWER: 120
what establishes the R-value ratings for windows and doors? - ANSWER: NFRC
where should the test hole be drilled for determining draft on appliances? -
ANSWER: 1'-2' downstream of the appliance draft diverter
what is the R-value of a window with a U factor of 0.25?
-2
-3
-1
,2|Pag e
-4 - ANSWER: 4
according to BPI standards, what must be kept on each crew vehicle and made
available to all workers and clients upon request? - ANSWER: Material Safety
Data Sheet
according to the BPI standards, what is the CAZ depressurization limit for an
orphaned natural draft water heater?
- -2cfm
- -2 pa
- -5cfm
- -5 pa - ANSWER: -2 pa
if wood is placed in wet soil, what moisture gradient will occur? - ANSWER: the
wetness of the soil will move into the wood
what does the blower door test evaluate? - ANSWER: air leakage level of the
building
according to ASHRAE, homes should receive at least __ air changes per hour or __
cfm per person - ANSWER: 0.35, 15
asbestos is a "known carcinogen" found in all of the following except?
-siding
-steam-pipe insulation
-floor tiles
-windows - ANSWER: windows
, 3|Pag e
digital readouts for carbon monoxide tests are given in:
-cubic inches per minute (CIM)
-cubic feet per minute (CFM)
-parts per million (PPM)
-inches of water column (IWC) - ANSWER: cubic feet per minute (CFM)
the first step when conducting a combustion appliance zone test is to:
-establish worst case
-measure the worst case spillage
-measure the base pressure
-action levels - ANSWER: measure the base pressure
the combination of air temperature, radiant temperature, humidity, and air
movement determine - ANSWER: comfort
what is not a sign flexible gas lines need to be replaced?
-if they're kinked
-if they're corroded
-if they're made of a silicone material
-if the line was manufactured before 1973 - ANSWER: if they're made of a
silicone material
why is window replacement usually not among the most cost-effective retrofits? -
ANSWER: new windows are expensive to buy and install
