©BRAINBARTER EXAM SOLUTIONS 2024/2025
ALL RIGHTS RESERVED.
CDC EOC Test Questions And Correct
Answers 100% Pass
TOs provide all of the following pertaining to the inspection operation, maintenance, and
modification of AF equipment and material except... - answer✔policy directives
Simply stated, a TO is considered to be... - answer✔a military order
TOs are established, numbered, and issued in accordance with which TO? - answer✔00-5-1
Which type of TO covers installation, operation, troubleshooting, repairing, removing,
calibration, and servicing, or handling of AF military systems? - answer✔operations and
maintenance TOs
Enhanced Technical Information Management System (ETIMS) provides a direct on-line
connectivity from every base into the management system to allow all except... - answer✔most
current publication date
To find the most current publication date of a TO, check... - answer✔the TO index
The Maintenance Integrated Data Access System is... - answer✔a six-digit numbering system
expressed as three elements of two digits each
What information does the NDI general system manual provide? - answer✔inspections
1|Page
, ©BRAINBARTER EXAM SOLUTIONS 2024/2025
ALL RIGHTS RESERVED.
What type of equipment manual would contain equipment calibration requirements? -
answer✔operation and service manual
A group assembly parts list has several part numbers listed for a part you need. To determine
which part number is right for your aircraft, refer to the... - answer✔usable on code column
Where would you find information for recording and reporting a NDI technique to inspect an F-
16C aircraft speed brake? - answer✔TO 33B-1-1
You are tasked to do an inspection; however you only know the name of the part you are to
inspect. To locate the applicable paragraph and figure number for the inspection, check the TOs
- answer✔alphabetical index
While doing a job you find a mistake in a TO. Correcting this requires initiation of a "Technical
Manual Change Recommendation and Reply" form. Who is responsible for this action? -
answer✔you
Which change recommendation priority must be answered within 40 calendar days? -
answer✔urgent
Which type change recommendation priority is used to recommend improvements to correct
potential hazards? - answer✔routine
Which TO contains complete instructions for maintaining TOs? - answer✔00-5-1
Electronic technical orders are files identified by a media distribution code suffix of... -
answer✔-WA-n
2|Page
, ©BRAINBARTER EXAM SOLUTIONS 2024/2025
ALL RIGHTS RESERVED.
You need to order a new TO for personnel use on a regular basis; how would you accomplish
this action? - answer✔establish an ID requirement
The TO listing for your shop's operational TO file will show you all of the following except... -
answer✔who currently has one signed out
Responsibility for consolidating TO requests on an installation rests with the... -
answer✔personnel in the TODO
With few exceptions, you must file TOs within a maximum of... - answer✔five workdays of
receipt
A TO effective date is... - answer✔later than the basic date
In which TO chapter would you find page 4-2? - answer✔4
File TO supplements in... - answer✔reverse numerical order in front of the basic TO
Enhanced Technical Information Management System (ETIMS) will be updated automatically in
no more than how many days? - answer✔7 calendar days
Who has ownership of AF supplies and equipment? - answer✔the american taxpayer
The purpose of the AF supply system is to... - answer✔provide a standard means of purchasing,
distributing, and controlling equipment/supplies required by the AF
Which system is used to determine whether your NDI laboratory is authorized a piece of
equipment? - answer✔AFEMS
3|Page
, ©BRAINBARTER EXAM SOLUTIONS 2024/2025
ALL RIGHTS RESERVED.
Which form is used to request an item not listed in the Federal Supply System? - answer✔DD
Form 1348-6
Which condition tag would be placed on an eddy current unit being sent back to depot for
repair? - answer✔Green DD Form 1577-2
All of these are requirements for an initial journeyman skill level except you must... -
answer✔complete 9 months of on-the-job training
From the lowest to the highest, what are the three levels of maintenance cabability? -
answer✔organizational, intermediate, depot
Which level of maintenance involves major repairs and overhaul? - answer✔depot
Which inspection involves a thorough and searching review of an entire weapon system? -
answer✔periodic (pe)
Which inspection attempts to minimize the length of time an aircraft is down for inspection? -
answer✔phase (ph)
Which inspection is based on calendar days? - answer✔isochronal (iso)
Which maintenance symbol would be used to indicate a scheduled periodic (pe) inspection is
overdue? - answer✔red dash
Which symbol signifies that an unsatisfactory condition exists? - answer✔red diagonal
4|Page
ALL RIGHTS RESERVED.
CDC EOC Test Questions And Correct
Answers 100% Pass
TOs provide all of the following pertaining to the inspection operation, maintenance, and
modification of AF equipment and material except... - answer✔policy directives
Simply stated, a TO is considered to be... - answer✔a military order
TOs are established, numbered, and issued in accordance with which TO? - answer✔00-5-1
Which type of TO covers installation, operation, troubleshooting, repairing, removing,
calibration, and servicing, or handling of AF military systems? - answer✔operations and
maintenance TOs
Enhanced Technical Information Management System (ETIMS) provides a direct on-line
connectivity from every base into the management system to allow all except... - answer✔most
current publication date
To find the most current publication date of a TO, check... - answer✔the TO index
The Maintenance Integrated Data Access System is... - answer✔a six-digit numbering system
expressed as three elements of two digits each
What information does the NDI general system manual provide? - answer✔inspections
1|Page
, ©BRAINBARTER EXAM SOLUTIONS 2024/2025
ALL RIGHTS RESERVED.
What type of equipment manual would contain equipment calibration requirements? -
answer✔operation and service manual
A group assembly parts list has several part numbers listed for a part you need. To determine
which part number is right for your aircraft, refer to the... - answer✔usable on code column
Where would you find information for recording and reporting a NDI technique to inspect an F-
16C aircraft speed brake? - answer✔TO 33B-1-1
You are tasked to do an inspection; however you only know the name of the part you are to
inspect. To locate the applicable paragraph and figure number for the inspection, check the TOs
- answer✔alphabetical index
While doing a job you find a mistake in a TO. Correcting this requires initiation of a "Technical
Manual Change Recommendation and Reply" form. Who is responsible for this action? -
answer✔you
Which change recommendation priority must be answered within 40 calendar days? -
answer✔urgent
Which type change recommendation priority is used to recommend improvements to correct
potential hazards? - answer✔routine
Which TO contains complete instructions for maintaining TOs? - answer✔00-5-1
Electronic technical orders are files identified by a media distribution code suffix of... -
answer✔-WA-n
2|Page
, ©BRAINBARTER EXAM SOLUTIONS 2024/2025
ALL RIGHTS RESERVED.
You need to order a new TO for personnel use on a regular basis; how would you accomplish
this action? - answer✔establish an ID requirement
The TO listing for your shop's operational TO file will show you all of the following except... -
answer✔who currently has one signed out
Responsibility for consolidating TO requests on an installation rests with the... -
answer✔personnel in the TODO
With few exceptions, you must file TOs within a maximum of... - answer✔five workdays of
receipt
A TO effective date is... - answer✔later than the basic date
In which TO chapter would you find page 4-2? - answer✔4
File TO supplements in... - answer✔reverse numerical order in front of the basic TO
Enhanced Technical Information Management System (ETIMS) will be updated automatically in
no more than how many days? - answer✔7 calendar days
Who has ownership of AF supplies and equipment? - answer✔the american taxpayer
The purpose of the AF supply system is to... - answer✔provide a standard means of purchasing,
distributing, and controlling equipment/supplies required by the AF
Which system is used to determine whether your NDI laboratory is authorized a piece of
equipment? - answer✔AFEMS
3|Page
, ©BRAINBARTER EXAM SOLUTIONS 2024/2025
ALL RIGHTS RESERVED.
Which form is used to request an item not listed in the Federal Supply System? - answer✔DD
Form 1348-6
Which condition tag would be placed on an eddy current unit being sent back to depot for
repair? - answer✔Green DD Form 1577-2
All of these are requirements for an initial journeyman skill level except you must... -
answer✔complete 9 months of on-the-job training
From the lowest to the highest, what are the three levels of maintenance cabability? -
answer✔organizational, intermediate, depot
Which level of maintenance involves major repairs and overhaul? - answer✔depot
Which inspection involves a thorough and searching review of an entire weapon system? -
answer✔periodic (pe)
Which inspection attempts to minimize the length of time an aircraft is down for inspection? -
answer✔phase (ph)
Which inspection is based on calendar days? - answer✔isochronal (iso)
Which maintenance symbol would be used to indicate a scheduled periodic (pe) inspection is
overdue? - answer✔red dash
Which symbol signifies that an unsatisfactory condition exists? - answer✔red diagonal
4|Page
