IEC 213 QUESTIONS & VERIFIED
RATIONALIZED ANSWERS 100%
GUARANTEE PASS
vWhen the corrected ampacity of a 10 AWG copper conductor is 12.86 amps, the maximum size circuit
breaker permitted to protect the conductors is ___. - 15
According to 240.4(D)(7), the largest circuit breaker that can be used to protect a circuit that uses 10
AWG conductors has a rating of ___ A. - 30
A 240-volt load, such as a window unit air conditioner, would require breaker ___ to be installed in the
panelboard. - b
Generally, circuit breakers must be ___. - readily accessible
What is the maximum voltage between circuit conductors when using plug fuses? - 125
Refer to Figure 204.5. The conductors at Point I are ___. - taps
Where installed in a 3-pole, 600-volt fused safety switch, the minimum number of fuses required to
protect a 120-volt, 1-ph, 2-wire branch circuit is ___. - 1
The secondary of a 300 KVA, 480 - 240-volt Δ-Δ transformer is delivering 100 amps to 3Ø loads. Based on
this load, the smallest permitted primary and secondary conductors are installed.
Refer to Scenario 223.51. The maximum rating of the primary OCPD is ___ A. - 100
The secondary of a 300 KVA transformer delivers power to a 180-amp, 3Ø load. This is a 480 — 240 volt
Δ-Δ transformer. Primary and secondary conductors are the minimum size required to serve the load.
, Refer to Scenario 220.53. The secondary OCPD can have a rating no greater than ___ amps. - 200
Section 240.21(C)(6) in the NEC® is the "25 foot rule." This section requires that the secondary
conductors be 25 feet or shorter in length and ___.
I. have an ampacity that is ≥ [(Pri OCPD ÷ 3) × (Epri line ÷ Esec line)]
II. have an ampacity that is ≥ the rating of the circuit breaker or fuses at the end
III. be installed in a raceway or otherwise protected from physical damage - I, II, & III
Circuit breakers shall be marked with a voltage rating not less than the nominal system voltage that is
indicative of their capability to interrupt fault currents ___.
I. between phases
II. from phase to ground
III. between the neutral and ground - I & II only
Handles or levers of circuit breakers, and similar parts which may move suddenly in such a way that
persons in the vicinity are likely to be injured by being struck by them, shall be ___.
I. concealed
II. isolated
III. guarded - II or III only
If a fuse label is not marked with a fuse interrupting rating, the fuse size has ___. - an interrupting rating
of 10,000 amps
A conductor has a computed ampacity of 75 amps. What is the maximum standard ampere rating of the
overcurrent protection device the NEC® permits to protect this circuit? This is not a motor circuit or part
of a multioutlet branch circuit supplying receptacles. - 80 amperes
If the allowable current rating of a busway is 1400 amps, what is the maximum allowable rating of the
overcurrent protection device that may be used to protect the busway? - 1200 amps
RATIONALIZED ANSWERS 100%
GUARANTEE PASS
vWhen the corrected ampacity of a 10 AWG copper conductor is 12.86 amps, the maximum size circuit
breaker permitted to protect the conductors is ___. - 15
According to 240.4(D)(7), the largest circuit breaker that can be used to protect a circuit that uses 10
AWG conductors has a rating of ___ A. - 30
A 240-volt load, such as a window unit air conditioner, would require breaker ___ to be installed in the
panelboard. - b
Generally, circuit breakers must be ___. - readily accessible
What is the maximum voltage between circuit conductors when using plug fuses? - 125
Refer to Figure 204.5. The conductors at Point I are ___. - taps
Where installed in a 3-pole, 600-volt fused safety switch, the minimum number of fuses required to
protect a 120-volt, 1-ph, 2-wire branch circuit is ___. - 1
The secondary of a 300 KVA, 480 - 240-volt Δ-Δ transformer is delivering 100 amps to 3Ø loads. Based on
this load, the smallest permitted primary and secondary conductors are installed.
Refer to Scenario 223.51. The maximum rating of the primary OCPD is ___ A. - 100
The secondary of a 300 KVA transformer delivers power to a 180-amp, 3Ø load. This is a 480 — 240 volt
Δ-Δ transformer. Primary and secondary conductors are the minimum size required to serve the load.
, Refer to Scenario 220.53. The secondary OCPD can have a rating no greater than ___ amps. - 200
Section 240.21(C)(6) in the NEC® is the "25 foot rule." This section requires that the secondary
conductors be 25 feet or shorter in length and ___.
I. have an ampacity that is ≥ [(Pri OCPD ÷ 3) × (Epri line ÷ Esec line)]
II. have an ampacity that is ≥ the rating of the circuit breaker or fuses at the end
III. be installed in a raceway or otherwise protected from physical damage - I, II, & III
Circuit breakers shall be marked with a voltage rating not less than the nominal system voltage that is
indicative of their capability to interrupt fault currents ___.
I. between phases
II. from phase to ground
III. between the neutral and ground - I & II only
Handles or levers of circuit breakers, and similar parts which may move suddenly in such a way that
persons in the vicinity are likely to be injured by being struck by them, shall be ___.
I. concealed
II. isolated
III. guarded - II or III only
If a fuse label is not marked with a fuse interrupting rating, the fuse size has ___. - an interrupting rating
of 10,000 amps
A conductor has a computed ampacity of 75 amps. What is the maximum standard ampere rating of the
overcurrent protection device the NEC® permits to protect this circuit? This is not a motor circuit or part
of a multioutlet branch circuit supplying receptacles. - 80 amperes
If the allowable current rating of a busway is 1400 amps, what is the maximum allowable rating of the
overcurrent protection device that may be used to protect the busway? - 1200 amps