BSSM EXAM STUDY GUIDE
how long does it take a burn to occur with 120F water - Answer 5 minutes
how long does it take a burn to occur with 130F water - Answer 30 secondsd
how long does it take a burn to occur with 140F water - Answer 5 seconds
how long does it take a burn to occur with 150F water - Answer 1.8 seconds
surface/outer layer of skin - Answer epidermis
where does a 2nd degree burn occur - Answer dermis
where does a 1st degree burn occur - Answer epidermis
where does 3rd &4th degree burns occur - Answer fat, muscle, & bone
most common type of burn - Answer thermal burn
causative agents of thermal burn - Answer sunburn, UV rays, hot water, open flame, fire,
contact with hot object (grabbing a pan)
priority tx of thermal burn - Answer extinguish the flame/stop the burn
then flush with cool water. <10% TBSA can use clean cool tap water & damp towel
chemical burns causes - Answer pesticides, chemicals, gasoline
who is @ risk for chemical burns - Answer farmers, those working in big plants that use
lots of chemicals
priority tx of chemical burns - Answer remove any clothing
copious amounts of irrigation to dilute/neutralize
debride blisters
call poison control if ingested
electrical burns: AC (alternating current) - Answer starts & stops which can cause
prolonged muscle contraction making it difficult for the source to leave prolonging
exposure
electrical burns: DC (direct current) - Answer will shoot you across the room
which is worse AC or DC - Answer AC (prolonged exposure)
chemical burns: acidotic or alkalotic more difficult to manage? - Answer alkalotic -
cause melting
, what to monitor for with electrical burns - Answer dysrhythmias, acute tubular necrosis,
& AKI
priority tx of electrical burns - Answer turn it off!! (disconnect source of electricity)
rapidly assess pt (look for entrance & exit points)
initiate CPR
how long to monitor electrical burn - Answer keep for at least 24 hrs after injury cuz they
can go into lethal arrhythmia
why is it important to know if electrical burn is AC or DC - Answer extent of injuries
underneath skin --> wont be able to see everything but underneath skin is fried
cold thermal burn causes - Answer prolonged cold weather exposure; frostbite
priority tx of cold thermal burn - Answer remove from heat & gently rewarm in warm
water untilskin is red & warm
what NOT to do with cold thermal burn - Answer dont: rewarm unless you are able to
keep them warm, use direct heat from heating pads/radiation/fire (sensation is numb &
can lead to burn injury), rub or massage the skin or break blisters
cold thermal burn normally affects - Answer fingers, toes, nose, & ears
smoke inhalation burn is a major predictor of.... - Answer mortality
sx of smoke inhalation burn - Answer stridor, soot around mouth
first 24-48 hrs after smoke inhalation can develop - Answer ARDS
causative agents of smoke inhalation burns - Answer carbon monoxide, breathing in hot
air
injuries from smoke inhalation - Answer metabolic asphyxiation
lower & upper airway injuries
priority tx of smoke inhalation burn - Answer remove the source, rapid assessment &
intubation, watch for first 24-48hrs for development of ARDS
1st degree burn AKA - Answer superficial partial thickness
2nd degree burn AKA - Answer deep partial thickenss
3rd & 4th degree burns AKA - Answer full thickness
manifestations of 1st degree burn - Answer redness (erythema), blanches, warm to
touch
does not blister
how long does it take a burn to occur with 120F water - Answer 5 minutes
how long does it take a burn to occur with 130F water - Answer 30 secondsd
how long does it take a burn to occur with 140F water - Answer 5 seconds
how long does it take a burn to occur with 150F water - Answer 1.8 seconds
surface/outer layer of skin - Answer epidermis
where does a 2nd degree burn occur - Answer dermis
where does a 1st degree burn occur - Answer epidermis
where does 3rd &4th degree burns occur - Answer fat, muscle, & bone
most common type of burn - Answer thermal burn
causative agents of thermal burn - Answer sunburn, UV rays, hot water, open flame, fire,
contact with hot object (grabbing a pan)
priority tx of thermal burn - Answer extinguish the flame/stop the burn
then flush with cool water. <10% TBSA can use clean cool tap water & damp towel
chemical burns causes - Answer pesticides, chemicals, gasoline
who is @ risk for chemical burns - Answer farmers, those working in big plants that use
lots of chemicals
priority tx of chemical burns - Answer remove any clothing
copious amounts of irrigation to dilute/neutralize
debride blisters
call poison control if ingested
electrical burns: AC (alternating current) - Answer starts & stops which can cause
prolonged muscle contraction making it difficult for the source to leave prolonging
exposure
electrical burns: DC (direct current) - Answer will shoot you across the room
which is worse AC or DC - Answer AC (prolonged exposure)
chemical burns: acidotic or alkalotic more difficult to manage? - Answer alkalotic -
cause melting
, what to monitor for with electrical burns - Answer dysrhythmias, acute tubular necrosis,
& AKI
priority tx of electrical burns - Answer turn it off!! (disconnect source of electricity)
rapidly assess pt (look for entrance & exit points)
initiate CPR
how long to monitor electrical burn - Answer keep for at least 24 hrs after injury cuz they
can go into lethal arrhythmia
why is it important to know if electrical burn is AC or DC - Answer extent of injuries
underneath skin --> wont be able to see everything but underneath skin is fried
cold thermal burn causes - Answer prolonged cold weather exposure; frostbite
priority tx of cold thermal burn - Answer remove from heat & gently rewarm in warm
water untilskin is red & warm
what NOT to do with cold thermal burn - Answer dont: rewarm unless you are able to
keep them warm, use direct heat from heating pads/radiation/fire (sensation is numb &
can lead to burn injury), rub or massage the skin or break blisters
cold thermal burn normally affects - Answer fingers, toes, nose, & ears
smoke inhalation burn is a major predictor of.... - Answer mortality
sx of smoke inhalation burn - Answer stridor, soot around mouth
first 24-48 hrs after smoke inhalation can develop - Answer ARDS
causative agents of smoke inhalation burns - Answer carbon monoxide, breathing in hot
air
injuries from smoke inhalation - Answer metabolic asphyxiation
lower & upper airway injuries
priority tx of smoke inhalation burn - Answer remove the source, rapid assessment &
intubation, watch for first 24-48hrs for development of ARDS
1st degree burn AKA - Answer superficial partial thickness
2nd degree burn AKA - Answer deep partial thickenss
3rd & 4th degree burns AKA - Answer full thickness
manifestations of 1st degree burn - Answer redness (erythema), blanches, warm to
touch
does not blister