MSF Course Questions & Solutions

MSF Course Questions & Solutions Why is motorcycling considered serious fun? Serious because there is risk involved, fun because riding a motorcycle is a joy. Learning to ride well requires what physical traits? Be healthy, have fitness, strength, and coordination. Previous Play Next Rewind 10 seconds Move forward 10 seconds Unmute 0:00 / 0:15 Full screen Brainpower Read More What do RiderCoaches do? They are here to guide me. What are the four requirements for successful course completion? 1. Complete all course assignments. 2. Attend all sessions fully. 3. Pass a knowledge test. 4. Pass an on-motorcycle skill test. When does a RiderCoach not permit further riding in the course? If you have a lot of difficulty, or become a danger to yourself and/or others. What are the three basic motorcycle types? Street, Dual-Purpose, Off-Highway What motorcycle type will you likely ride? Why? I will likely ride a street motorcycle and use it for transportation. What are the six primary motorcycle controls? Clutch, handle bars, front brake lever, throttle, gearshift lever, rear brake pedal. How do you operate a motorcycles throttle? To increase engine speed, twist towards you. To decrease engine speed, twist away. What does the clutch lever do? It connects power from the engine to the rear wheel. Squeeze it in to disconnect the power and ease it out to connect. How is the gearshift lever operated? Lift up firmly and release for a higher gear, press down firmly and release for a lower gear. What is a shift pattern? ? How are the two brake controls operated? Front brake is squeezed rear brake is pressed down. What are possible positions on the fuel valve? On, reserve, prime, off. What are possible positions on the ignition switch? On, off, lock, and sometimes park. What is the choke control used for? It provides an enriched fuel mixture to help start a cold engine. Why does a motorcycle have an engine cut-off switch? It allows you to shut off the engine without removing your hand from the grip. What are some common indicators that display information? Speedometer, odometer, tachometer. What is important to know about a convex mirror? They provide a wider view but make objects look farther away. What is the difference between a side stand and a center stand? A side stand supports a motorcycle when parked, a center stand makes the motorcycle upright and raises the rear tire for maintenance. Complete the Controls Quiz on page 7 and check your answers Just google a picture of motorcycle controls and study it. List the five steps of the engine pre-start routine. FINE-C; Fuel, Ignition, Neutral, Engine cut-off switch, Choke/Clutch. What are the three steps to follow when shutting off the engine? 1. Turn the engine cut-off switch to off with your right thumb. 2. Turn the ignition switch to off. 3. Turn the fuel supply valve to off. What is the friction zone? A small area of travel in the clutch lever that controls connection the engine to the rear wheel. What does squeezing the clutch lever do? Removes power from the rear wheel. What must you do if you start to lose control of the motorcycle? Squeeze in the clutch firmly and use the brakes as needed. What is the position of the right wrist for good riding posture? Fingers around the throttle with a flat wrist. What are the other elements of proper riding posture? Keep your back straight, head and eyes up, feet on footrests near the controls. How do you initiate motorcycle lean at speeds higher than walking speed? Lean the motorcycle and turn the handlebars in the direction you want to go. What are the four action steps for making a basic turn? Slow, Look, Press and Roll. What is the three-step strategy for curves and what does each step mean? Search-Setup-Smooth. Search: while approaching a curve search for key information. Setup: adjust speed and lane position as necessary before entering. Smooth: operate the controls so there are no jerky movements. In what type of turn does counterweighting help? U-turns What gear should you be in when coming to a stop and why? First gear, so it is easier to start rolling again and so you don't stall. What is the benefit of squaring the handlebars when coming to a stop? So the motorcycle is easy to hold up. Why does the front brake have more stopping power than the rear brake? The weight shift pushes the front tire giving it more grip. How does the motorcycles weight sh It shifts forward. How do you stop in a curve? Gradually apply both brakes while straightening out the motorcycle. Why do you change gears? To match the engine speed with the road speed. List the three-step process to shift to a higher gear. Roll off, lift, ease out. List the three-step process to shift to a lower gear. Roll off, press down, ease out. What is engine braking? Shifting to a lower gear and easing out the clutch to slow down. What is the position of the clutch lever when making a stop? Fully squeezed. List the four preparations to ride. 1. You fit the bike. 2. Inspect the bike. 3. Wear protective gear. 4. Have a good mental attitude with safety as your priority. How should your motorcycle fit you? The seat should be low enough for you to reach the ground with your feet to support the motorcycle. What is T-CLOCS and what does each letter stand for? T- Tires and Wheels. C- Controls. L- Lights and Mirrors. O- Oil and Other Fluids. C- Chassis. S- Stands. What are the three primary purposes of riding gear? 1. Keeps you comfortable and focused. 2. Keeps your body protected. 3. Keeps you visible. What does ATGATT mean? All the gear, all the time. What type of injury accounts for the majority of motorcycle-related deaths? Head injury. What are the four basic parts of a helmet? Outer shell, impact absorbing liner, comfort padding, retention system. What is the difference between a full-face-coverage helmet and a three-quarter-coverage helmet? A full face helmet covers the chin, making it safer. What stickers are likely to indicate a well-made helmet? D.O.T, E.C.E and Snell How should a helmet fit? Snugly with no irritating pressure points. What are some tips to care for a helmet? Leave a damp towel on it then wipe off any dirtiness, wash removable liners.