MSSC STUDY GUIDE QUESTIONS WITH
VERIFIED SOLUTIONS RATED A.
Compressed ____________ can be used for cleaning work surfaces as
long as the dead-headed pressure does not exceed 30 psi
Correct Answer -air
Effective training in air powered tools helps employee's ___________.
Correct Answer -avoid work hazards
One or more hoses crossing a main walkway ____________.
Correct Answer -Are not acceptable
When using pneumatic tools _____________.
Correct Answer -Do not use compressed air to clean clothing or skin
You should never _____________ because it might cause damage
Correct Answer -Use compressed air to clean clothing
After a regulator is installed on an oxygen cylinder, the cylinder valve
should always be _____________.
Correct Answer -Opened all the way to prevent leakage around the valve
As a safety precaution, which of these should be chained to a rigid
fixture?
Correct Answer -a compressed gas cylinder
,Stamps on the body of compressed gas cylinders indicate
______________.
Correct Answer -the safety test date
Gloves and safety glasses are necessary when working with
_____________
Correct Answer -With sharp or rough sheet metal
The document that identifies chemicals and sets limits for their use is
called a _____________.
Correct Answer -Material Safety data sheet
You should wear gloves when handling sheet metal because
______________.
Correct Answer -Sheet metal is very sharp and may cut you
A steep ladder is sometimes referred to as a(n) ________________.
Correct Answer -A-frame ladder
The highest load rating a ladder may have is _____________.
Correct Answer -Type IAA
A bucket should be used to _____________.
Correct Answer -Transfer tools up and down a ladder
When using an extension ladder, the distance the foot of the ladder is set
from the house should be about ___________ the height of the extension.
Correct Answer -1/4
,A ladder should extend at least ______________ feet above it point of
contact with the roof.
Correct Answer -3
A person should always face the ladder _____________.
Correct Answer -With no exceptions.
Always face the Ladder when ____________________.
Correct Answer -When climbing and descending
The ______________ is the part of a personal fall arrest system that
attaches to the building structure.
Correct Answer -Lifeline
Working areas at 6 feet or higher require _________.
Correct Answer -Fall protection
A single pry truck can be used to move a load ________________.
Correct Answer -A short distance
You should always know the ______________ of any load you are going
to move.
Correct Answer -Weight
When inserting a pry truck under a load, the lip of the pry truck should
_______________.
Correct Answer -Engage the load as far as possible
, _____________ is the act of securing a load to prepare it for a lifting
operation.
Correct Answer -Rigging
Are the cable clamps on the wire rope sling oriented correctly?
Correct Answer -True
Attachment devices such as _____________ are used to connect the load
to the sling and the sling to the lifting device.
Correct Answer -Eyebolts and shackles
The forces created on a sling __________ as the angle of a sling's legs
decrease.
Correct Answer -Increase
When attempting to lift a long I-beam use at least _____________ strap(s)
that is (are) _______________
Correct Answer -Two placed equally from the center.
Do not leave a load __________ while the hoist is unattended.
Correct Answer -suspended
When is it ok to use a hoist to lift something that weight more than the
rating on a hoist?
Correct Answer -Never
The safety devices on an electric hoist include both mechanical and
electrical protection.
Correct Answer -Overload
VERIFIED SOLUTIONS RATED A.
Compressed ____________ can be used for cleaning work surfaces as
long as the dead-headed pressure does not exceed 30 psi
Correct Answer -air
Effective training in air powered tools helps employee's ___________.
Correct Answer -avoid work hazards
One or more hoses crossing a main walkway ____________.
Correct Answer -Are not acceptable
When using pneumatic tools _____________.
Correct Answer -Do not use compressed air to clean clothing or skin
You should never _____________ because it might cause damage
Correct Answer -Use compressed air to clean clothing
After a regulator is installed on an oxygen cylinder, the cylinder valve
should always be _____________.
Correct Answer -Opened all the way to prevent leakage around the valve
As a safety precaution, which of these should be chained to a rigid
fixture?
Correct Answer -a compressed gas cylinder
,Stamps on the body of compressed gas cylinders indicate
______________.
Correct Answer -the safety test date
Gloves and safety glasses are necessary when working with
_____________
Correct Answer -With sharp or rough sheet metal
The document that identifies chemicals and sets limits for their use is
called a _____________.
Correct Answer -Material Safety data sheet
You should wear gloves when handling sheet metal because
______________.
Correct Answer -Sheet metal is very sharp and may cut you
A steep ladder is sometimes referred to as a(n) ________________.
Correct Answer -A-frame ladder
The highest load rating a ladder may have is _____________.
Correct Answer -Type IAA
A bucket should be used to _____________.
Correct Answer -Transfer tools up and down a ladder
When using an extension ladder, the distance the foot of the ladder is set
from the house should be about ___________ the height of the extension.
Correct Answer -1/4
,A ladder should extend at least ______________ feet above it point of
contact with the roof.
Correct Answer -3
A person should always face the ladder _____________.
Correct Answer -With no exceptions.
Always face the Ladder when ____________________.
Correct Answer -When climbing and descending
The ______________ is the part of a personal fall arrest system that
attaches to the building structure.
Correct Answer -Lifeline
Working areas at 6 feet or higher require _________.
Correct Answer -Fall protection
A single pry truck can be used to move a load ________________.
Correct Answer -A short distance
You should always know the ______________ of any load you are going
to move.
Correct Answer -Weight
When inserting a pry truck under a load, the lip of the pry truck should
_______________.
Correct Answer -Engage the load as far as possible
, _____________ is the act of securing a load to prepare it for a lifting
operation.
Correct Answer -Rigging
Are the cable clamps on the wire rope sling oriented correctly?
Correct Answer -True
Attachment devices such as _____________ are used to connect the load
to the sling and the sling to the lifting device.
Correct Answer -Eyebolts and shackles
The forces created on a sling __________ as the angle of a sling's legs
decrease.
Correct Answer -Increase
When attempting to lift a long I-beam use at least _____________ strap(s)
that is (are) _______________
Correct Answer -Two placed equally from the center.
Do not leave a load __________ while the hoist is unattended.
Correct Answer -suspended
When is it ok to use a hoist to lift something that weight more than the
rating on a hoist?
Correct Answer -Never
The safety devices on an electric hoist include both mechanical and
electrical protection.
Correct Answer -Overload
