NETA 2 EXAM 2024/2025 WITH 100%
ACCURATE SOLUTIONS
user
[COMPANY NAME] [Company address]
,Under what considerations can tag out without lock out be permitted? -
Precise Answer ✔✔***&If an energy isolating device is not capable of
being locked
For PV systems, a(n) _____ is a device that changes direct-current input
to an alternating-current output. - Precise Answer ✔✔Inverter
Identify the contact pictured above. (NC and NO separated by a node) -
Precise Answer ✔✔Form C
When applying personal protective grounds, which end is attached first?
- Precise Answer ✔✔***&The equipment end
An induction motor has 40kVA input power, a power factor of 82
percent, and an efficiency of 92 percent. What is the horsepower? -
Precise Answer ✔✔***&30.2 HP
How many connection points would you expect to find on a kelvin
bridge? - Precise Answer ✔✔4
You arrive at a job to perform acceptance testing on a new-indoor 15KV
switch lineup. While the equipment has been installed multiple covers
are off there are power conductors hanging with taped ends. What
should you do? - Precise Answer ✔✔***&Visually confirm that the
source of power have already been de-energized and lock out
,What is the turns ratio of a 3-phase 500kVA, 13,200-480 volt rated
delta-delta transformer that is 80% loaded? - Precise Answer
✔✔***&22.000
***27.500
ASTM D 924 is a required acceptance test for liquid-filled transformers
with natural ester insulating fluid per NETA standards. - Precise Answer
✔✔***&True
NETA-ATS requires test decals be affixed on the exterior of equipment
or equipment enclosure of protective devices after performing electrical
tests. Which color test decal would you affix to a piece of equipment
with a minor deficiency that does not affect its fault detection or
operation? - Precise Answer ✔✔Yellow
What is meant by a "dead tank breaker?" - Precise Answer ✔✔The
external tank is grounded.
If you have your ground conductor running through your zero-sequence
CT with your current carrying conductors, what will happen? - Precise
Answer ✔✔Ground fault protection won't function
Which of the following would best describe a 52 device: - Precise
Answer ✔✔AC circuit breaker
, A series circuit has two resistors. The resistors dissipate 10 W and 15 W.
What is the total power dissipation of the circuit? - Precise Answer
✔✔25 W
Which of the following would be the best choice for use in both the
conductive and mechanical areas of circuit breakers and switches? -
Precise Answer ✔✔Mobil 28
What is the power factor temperature correction value for new mineral
oil? - Precise Answer ✔✔***&20C/40C
OSHA requires the testing of a volt meter after a voltage test on voltage
above ______. - Precise Answer ✔✔600V
A tagout device must be strong enough to remain attached under a
minimum of ____ lbs of force. - Precise Answer ✔✔50
A piece of wire that is 0.001 inches in diameter and 12 inches long is
one mil-foot. - Precise Answer ✔✔True
At least 2 entrances of sufficient area must be provided giving access to
the electrical equipment working space. - Precise Answer ✔✔***&True
What is the Restricted Approach Boundary for a 69kV system? - Precise
Answer ✔✔***&3 ft 10 in.
ACCURATE SOLUTIONS
user
[COMPANY NAME] [Company address]
,Under what considerations can tag out without lock out be permitted? -
Precise Answer ✔✔***&If an energy isolating device is not capable of
being locked
For PV systems, a(n) _____ is a device that changes direct-current input
to an alternating-current output. - Precise Answer ✔✔Inverter
Identify the contact pictured above. (NC and NO separated by a node) -
Precise Answer ✔✔Form C
When applying personal protective grounds, which end is attached first?
- Precise Answer ✔✔***&The equipment end
An induction motor has 40kVA input power, a power factor of 82
percent, and an efficiency of 92 percent. What is the horsepower? -
Precise Answer ✔✔***&30.2 HP
How many connection points would you expect to find on a kelvin
bridge? - Precise Answer ✔✔4
You arrive at a job to perform acceptance testing on a new-indoor 15KV
switch lineup. While the equipment has been installed multiple covers
are off there are power conductors hanging with taped ends. What
should you do? - Precise Answer ✔✔***&Visually confirm that the
source of power have already been de-energized and lock out
,What is the turns ratio of a 3-phase 500kVA, 13,200-480 volt rated
delta-delta transformer that is 80% loaded? - Precise Answer
✔✔***&22.000
***27.500
ASTM D 924 is a required acceptance test for liquid-filled transformers
with natural ester insulating fluid per NETA standards. - Precise Answer
✔✔***&True
NETA-ATS requires test decals be affixed on the exterior of equipment
or equipment enclosure of protective devices after performing electrical
tests. Which color test decal would you affix to a piece of equipment
with a minor deficiency that does not affect its fault detection or
operation? - Precise Answer ✔✔Yellow
What is meant by a "dead tank breaker?" - Precise Answer ✔✔The
external tank is grounded.
If you have your ground conductor running through your zero-sequence
CT with your current carrying conductors, what will happen? - Precise
Answer ✔✔Ground fault protection won't function
Which of the following would best describe a 52 device: - Precise
Answer ✔✔AC circuit breaker
, A series circuit has two resistors. The resistors dissipate 10 W and 15 W.
What is the total power dissipation of the circuit? - Precise Answer
✔✔25 W
Which of the following would be the best choice for use in both the
conductive and mechanical areas of circuit breakers and switches? -
Precise Answer ✔✔Mobil 28
What is the power factor temperature correction value for new mineral
oil? - Precise Answer ✔✔***&20C/40C
OSHA requires the testing of a volt meter after a voltage test on voltage
above ______. - Precise Answer ✔✔600V
A tagout device must be strong enough to remain attached under a
minimum of ____ lbs of force. - Precise Answer ✔✔50
A piece of wire that is 0.001 inches in diameter and 12 inches long is
one mil-foot. - Precise Answer ✔✔True
At least 2 entrances of sufficient area must be provided giving access to
the electrical equipment working space. - Precise Answer ✔✔***&True
What is the Restricted Approach Boundary for a 69kV system? - Precise
Answer ✔✔***&3 ft 10 in.
