75-Pump Operation and Maintenance
75-Pump Operation and Maintenance Questions and Answers Positive displacement compressors: a) cannot deliver pulsation-free air b) cannot deliver oil-free air c) must have suction and discharge valves d) must use all internal lubrication e) could be single stage with three cylinders E Single stage reciprocating air compressors have: a) one or more cylinders of equal size b) variable speed drivers c) several cylinders, each of different sizes d) low power requirements e) intercoolers A Compressed air machinery would most likely be used in a) coal mines b) residential garages c) home furnace control systems d) agricultural applications e) tool and die shops A Compressed air tools tend to be a) heavier than equivalent electrical tools b) damaged by overloading c) hot after prolonged operation d) more expensive than electrical tools e) less compact than electrical tools D In a centrifugal compressor the kinetic energy is converted to potential energy in the a) volute, diffuser, or both b) intercooler c) diffuser only d) compressor cavity e) volute only A The compressor which would favour volume over pressure would be the a) rotary lobe b) screw c) axial d) centrifugal e) sliding vane D Positive displacement air compressor types are a) centrifugal compressors b) gear compressors c) axial compressors d) multi-stage centrifugal compressors e) not capable of producing high discharge pressures B Single stage reciprocating air compressors a) must have an air receiver b) could be of the rotary type c) do need an intercooler d) could have two cylinders e) have a smooth discharge delivery D A belt driven lubricator is very popular on a a) reciprocating double acting unit b) screw unit c) rotary lobe unit d) centrifugal unit e) sliding vane unit E A speed-increasing gear is commonly used on a) rotary lobe compressors b) screw compressors c) sliding vane compressors d) reciprocating compressors e) centrifugal compressors B Relative to a dry-pipe fire system, an automatic air supply shall be connected so that proper pressure can be maintained in each system, is a statement of the a) National Fire Protection Association Code b) Industrial Accident Prevention Association c) Canadian Standards Association d) Occupational Health and Safety e) Society of Municipal Fire Marshalls A In order to protect the driver, a start-stop air compressor should be equipped with a) an intercooler b) an automatic blowdown system c) safety heads d) pre-start automatic unloading e) manual cylinder bleed petcocks D The valves on a reciprocating compressor are opened by a) a pressure difference b) the cam shaft c) the eccentric d) hydraulic pressure e) a timing gear A Compressor unloaders a) could close the discharge valve b) must be used on centrifugal compressors c) could keep the suction valve open d) activate the stop and start button e) are located on the driver of the compressor C Where pistons move in a cylinder it is necessary for the lubricant to provide a) tension b) sealing c) alignment d) shock reduction e) vapour venting B An air compressor which gives two compression strokes per crankshaft revolution is a) multistaged two cylinder b) multicylinder single acting c) single cylinder double acting d) a compound unit e) single acting C To reduce air temperature between stages, we would use a) an intercooler b) an aftercooler c) a receiver d) a converter e) a chiller A An air receiver used in an air compression, system will perform the following functions: 1. act as a storage vessel 2. eliminates pulsation in discharge lines 3. will separate out water from the air 4. controls the temperature of the air before it enters the system a) 1, 2 b) 1, 2, 3 c) 1, 2, 4 d) 2, 3, 4 e) 3, 4 B An air compressor auxiliary which will decrease the power requirement is the a) receiver b) diffuser c) intercooler d) variable compression ratio head e) aftercooler C Intercoolers should be equipped with a) moisture separators b) safety valves c) baffles d) vents e) automatic blowdowns B An air compressor auxiliary which will decrease the power requirement is the a) receiver b) diffuser c) intercooler d) variable compression ratio head e) aftercooler C
Información del documento
- Subido en
- 22 de julio de 2024
- Número de páginas
- 8
- Escrito en
- 2023/2024
- Tipo
- Examen
- Contiene
- Preguntas y respuestas