• ¿Documento equivocado? Cámbialo gratis
  • Escrito por estudiantes que aprobaron
  • Inmediatamente disponible después del pago
  • Leer en línea o como PDF
Vender
¿Dónde estudias?
Tu idioma
Document preview thumbnail
Vista previa 2 fuera de 11 páginas
Examen

Millwright Manual Alignment Test Solved 100%

Document preview thumbnail
Vista previa 2 fuera de 11 páginas

Why are machines accurately aligned with each other? 23:1 - Answer Machines are accurately aligned to work together smoothly. Thus increasing working life. How is the Primary unit positioned? 23:1 - Answer The primary unit is positioned according to reference lines (centre-lines, benchmarks etc) What are the other machines aligned with the Primary unit? 23:1 - Answer Drive units; prime movers, transmission units etc. Are usually aligned with the primary unit. How is an alignment procedure chosen? 23:2 - Answer The alignment procedure used is determined by the type of components connecting the units. What procedure is used to align coaxial shafts? 23:2 - Answer In-line (coaxial shafts) are usually alogned with couplings in a procedure called coupling alignment. What are the results of coaxial misalignment? 23:2 - Answer Results of coaxial misalignment are: -reduced bearing life -coupling damage -high vibration -reduced seal life -increased downtime and costs What conditions of misalignment are present in misaligned coaxial shafts? 23:2 - Answer -offset -angular To align shafts correctly, in what two planes must these conditions be solved? 23:2 - Answer Shafts must be align in both horizontal & vertical planes Why is vertical alignment corrected first? 23:3 - Answer Because it is very easy to disturb horizontal alignment when correcting the vertical alignment. How is vertical misalignment corrected? 23:3 - Answer By using shims underneath the machine feet How is horizontal alignment corrected? 23:3 - Answer By adjusting the position of the unit on its base with jacking screws Define angular misalignment. 23:3 - Answer Angular misalignment occurs when the coupling faces are not parallel with each otheras well as the shaft centre-lines. How is angular misalignment corrected horizontally & vertically? 23:3 - Answer Horizontal: jacking screws Vertical: correct amount of shims under front and back shims. Define offset misalignment. 23:3 - Answer When the centre-lines of both shafts are parallel but not in-line. How is offset misalignment corrected horizontally? 23:3 - Answer By moving jacking screws on one side evenly till shafts are in-line. How is offset misalignment corrected vertically? 23:3 - Answer By adding or removing an equal amount of shims from all feet to bring shafts in-line. Describe combination misalignment. 23:4 - Answer Combination misalignment occurs when both angular & offset misalignment are present between coaxial shafts. Define Softfoot. 23:4 - Answer Softfoot occurs when a machines feet do not equally support its weight; it does not sit firmly on all feet. How does softfoot effect the machine? 23:4 - Answer Softfoot will stress the machine housing and ovalize bearing bores. What causes Softfoot? 23:4 - Answer Softfoot can be caused by: -poorly machined feet -dirt under feet -in-correct anchor bolt torque -poor levelling -poor base design -grout deteriation -base or foot corrosion What are the two types of Softfoot? 23:4-5 - Answer -ordinary softfoot -angular softfoot What is a good foot-to-base fit? 23:4-5 - Answer Gap between foot and base should be less than 0.001" (0.025mm) How does thermal expansion & contraction affect alignment? 23:5 - Answer Thermal expansion and contraction will cause misalignment to develope as a machine warms up to or cools down from operating temperature.


Información del documento

Subido en
9 de septiembre de 2023
Número de páginas
11
Escrito en
2023/2024
Tipo
Examen
Contiene
Preguntas y respuestas
$13.49

¿Documento equivocado? Cámbialo gratis Dentro de los 14 días posteriores a la compra y antes de descargarlo, puedes elegir otro documento. Puedes gastar el importe de nuevo.
Escrito por estudiantes que aprobaron
Inmediatamente disponible después del pago
Leer en línea o como PDF

Seller avatar
Los indicadores de reputación están sujetos a la cantidad de artículos vendidos por una tarifa y las reseñas que ha recibido por esos documentos. Hay tres niveles: Bronce, Plata y Oro. Cuanto mayor reputación, más podrás confiar en la calidad del trabajo del vendedor.
Grademasters
3.8
(46)
Vendido
118
Seguidores
69
Artículos
2591
Última venta
1 mes hace




Por qué los estudiantes eligen Stuvia

Creado por compañeros estudiantes, verificado por reseñas

Calidad en la que puedes confiar: escrito por estudiantes que aprobaron y evaluado por otros que han usado estos resúmenes.

¿No estás satisfecho? Elige otro documento

¡No te preocupes! Puedes elegir directamente otro documento que se ajuste mejor a lo que buscas.

Paga como quieras, empieza a estudiar al instante

Sin suscripción, sin compromisos. Paga como estés acostumbrado con tarjeta de crédito y descarga tu documento PDF inmediatamente.

Student with book image

“Comprado, descargado y aprobado. Así de fácil puede ser.”

Alisha Student

Preguntas frecuentes

Ups! No podemos cargar tu documento ahora. Inténtalo de nuevo o contacta con soporte.