• ¿Documento equivocado? Cámbialo gratis
  • Escrito por estudiantes que aprobaron
  • Inmediatamente disponible después del pago
  • Leer en línea o como PDF
Vender
¿Dónde estudias?
Tu idioma
Document preview thumbnail
Vista previa 1 fuera de 3 páginas
Examen

Irc Study Session 7| Questions With Complete Solutions

Document preview thumbnail
Vista previa 1 fuera de 3 páginas

What is the maximum center-to-center stud spacing permitted for a 2 inch by 6 inch, 8 foot high wood stud bearing wall supporting two floors, roof and ceiling? Correct Answer: 16 incesh In wood wall framing where top and bottom plates are attached to the studs, which of the following fastening methods is acceptable? Correct Answer: three 10d box, end nailed The minimum offset for end joints in a double top plate shall be ____________ Correct Answer: 24 inches A single top plate is permitted in a wood stud bearing wall only where the raters or joists are centered over the studs with a maximum tolerance of _______________ Correct Answer: 1 inch Where the wall sheathing is used to resist wind pressures, what is the maximum stud spacing permitted for 3/8 -inch wood structural panel wall sheathing with a span rating of 24/0. Correct Answer: 16 inches o.c In a non-bearing partition, a wood stud may be notches a maximum of Correct Answer: 40 percent of the stud width A bored hole shall be located a minimum of ____________- from the edge of a wood stud. Correct Answer: 5/8 inch In a nonbearing interior partition, what is the maximum diameter permitted for a bored hole in a wood stud? Correct Answ

Vista previa del contenido

IRC STUDY SESSION 7| QUESTIONS WITH
COMPLETE SOLUTIONS
What is the maximum center-to-center stud spacing permitted for a 2 inch by 6 inch, 8 foot high
wood stud bearing wall supporting two floors, roof and ceiling? Correct Answer: 16 incesh

In wood wall framing where top and bottom plates are attached to the studs, which of the
following fastening methods is acceptable? Correct Answer: three 10d box, end nailed

The minimum offset for end joints in a double top plate shall be ____________ Correct Answer:
24 inches

A single top plate is permitted in a wood stud bearing wall only where the raters or joists are
centered over the studs with a maximum tolerance of _______________ Correct Answer: 1 inch

Where the wall sheathing is used to resist wind pressures, what is the maximum stud spacing
permitted for 3/8 -inch wood structural panel wall sheathing with a span rating of 24/0. Correct
Answer: 16 inches o.c

In a non-bearing partition, a wood stud may be notches a maximum of Correct Answer: 40
percent of the stud width

A bored hole shall be located a minimum of ____________- from the edge of a wood stud.
Correct Answer: 5/8 inch

In a nonbearing interior partition, what is the maximum diameter permitted for a bored hole in a
wood stud? Correct Answer: 60 percent of the stud width

A 15-inch-deep box header in an exterior wall is constructed with wood structural panels on both
sides. What is the maximum allowable header span for a condition where the header supports a
clear-span roof truss with a span of 26 feet? Correct Answer: 8 feet

Which fo the following materials is not specifically identified by the IRC as a fire-blocking
material? Correct Answer: 15/32-inch wood structural panel with joints backed

Where unfaced fiberglass batt insulation is used a fireblocking material in the wall cavity of a
wood stud wall system, the insulation shall be installed with a minimum vertical height of
__________________. Correct Answer: 16 inches

A foundation cripple wall shall be considered an additional story for stud sizing requirements
where the wall height exceeds ______________ in height. Correct Answer: 48 inches

The distance between adjacent edges of braced wall panels along a braced wall line must be a
maximum of __________ feet. Correct Answer: 20

Información del documento

Subido en
4 de noviembre de 2022
Número de páginas
3
Escrito en
2022/2023
Tipo
Examen
Contiene
Preguntas y respuestas
$6.99

¿Documento equivocado? Cámbialo gratis Dentro de los 14 días posteriores a la compra y antes de descargarlo, puedes elegir otro documento. Puedes gastar el importe de nuevo.
Escrito por estudiantes que aprobaron
Inmediatamente disponible después del pago
Leer en línea o como PDF

Seller avatar
Los indicadores de reputación están sujetos a la cantidad de artículos vendidos por una tarifa y las reseñas que ha recibido por esos documentos. Hay tres niveles: Bronce, Plata y Oro. Cuanto mayor reputación, más podrás confiar en la calidad del trabajo del vendedor.
HIGHFLYER
4.0
(82)
Vendido
288
Seguidores
263
Artículos
1817
Última venta
1 año hace




Por qué los estudiantes eligen Stuvia

Creado por compañeros estudiantes, verificado por reseñas

Calidad en la que puedes confiar: escrito por estudiantes que aprobaron y evaluado por otros que han usado estos resúmenes.

¿No estás satisfecho? Elige otro documento

¡No te preocupes! Puedes elegir directamente otro documento que se ajuste mejor a lo que buscas.

Paga como quieras, empieza a estudiar al instante

Sin suscripción, sin compromisos. Paga como estés acostumbrado con tarjeta de crédito y descarga tu documento PDF inmediatamente.

Student with book image

“Comprado, descargado y aprobado. Así de fácil puede ser.”

Alisha Student

Preguntas frecuentes