• ¿Documento equivocado? Cámbialo gratis
  • Escrito por estudiantes que aprobaron
  • Inmediatamente disponible después del pago
  • Leer en línea o como PDF
Vender
¿Dónde estudias?
Tu idioma
Document preview thumbnail
Vista previa 2 fuera de 15 páginas
Examen

MEC322 - Midterm Study Guide - Latest Edition Updated

Document preview thumbnail
Vista previa 2 fuera de 15 páginas

MEC322 - Midterm Study Guide - Latest Edition Updated What is Metrology? - answer - The science of measurement. It includes all theoretical and practical aspects of measurement. What are Dimensions? - answer - Linear or Angular sizes of a component specified on the part drawing What are tolerances? - answer - Allowable variations/permissible error from the specified part dimensions that are permitted in manufacturing. Can be by an amount or percentage. What do you call a tolerance in both the positive and negative direction? - answer - Bilateral Tolerance What is the definition of accuracy? - answer - How closely a measured value is to an accepted value (target) What is the definition of precision? - answer - How close a series of measurements are to each other What is the definition of circularity? - answer - Circularity of an object, also known as roundness What is the definition of concentricity? - answer - In geometry, two or more objects are said to be concentric, coaxal, or coaxial when they share the same center or axis. What is the definition of cylindricity? - answer - Cylindricity is a 3-Dimensional tolerance that controls the overall form of a cylindrical feature to ensure that it is round enough and straight enough along its axis. In inspection, which procedure provides more information? Gaging or Measuring? - answer - Measuring What is the definition of Gaging? - answer - Using a fixed tool/standard to determine a tool's measurements min/max. What material is a surface plate usually made of? - answer - Granite What is a graduated measuring device? - answer - Any device with markings for measures of length An outside micrometer is appropriate for measuring which of the following (two correct answers): (a) hole depth, (b) hole diameter, (c) part length, (d) shaft diameter (e) surface roughness - answer - (c) and (d) In a GO/NO-GO gage, which one of the following best describes the function of the GO gage? - answer - Checks the minimum size (minimum permissible dimension) What are two types of GO-NO GO Gauges? - answer - Snap Gauge (Clamp Shaped) and Plug Gauge (double ended), Limit Gauge Surface texture includes which of the following characteristics of a surface? - answer - 1) Deviations from the nominal surface, 2) Feed marks of the tool that produced the surface, 3) Surface Cracks Surface texture is included within the scope of surface integrity? True or False - answer - True Surface roughness can be measured as either an arithmetic average (AA) or a root-mean square (RMS) average. Which value is almost always greater for most surfaces? - answer - Root-mean square is always more favorable. Thermal energy is normally associated with which of the following changes in the altered layer? - answer - Hardness Variations Heat Affected Zone Recrystallization Which manufacturing process is likely to result in the best surface finish out of the ones listed below? (a) arc welding, (b) grinding, (c) machining, (d) sand casting, or (e) sawing - answer - (b) Grinding Which one of the following manufacturing processes is likely to result in the worst surface finish: (a) cold rolling, (b) grinding, (c) machining, (d) sand casting, or (e) sawing? - answer - Sand Casting What are the three different types of fits? - answer - Clearance Fit, Transition fit, Interference fit When referring to a shaft going into a hole, what would a clearance fit indicate? - answer - Indicates that the dimensions must be able to go into (clear) the shaft and thus the tolerances mus be at or below the shaft's tolerance. When referring to a shaft going into a hole, what would a transition fit indicate? - answer - Indicates that the dimension must be very similar or the same as the shaft. When referring to a shaft going into a hole, what would a interference fit indicate? - answer - Indicate that the dimension must be a little bit bigger than the shaft, and thus interfere with the hole. Nominal Surface - answer - designer's


Información del documento

Subido en
20 de noviembre de 2026
Número de páginas
15
Escrito en
2026/2027
Tipo
Examen
Contiene
Preguntas y respuestas
$13.99

¿Documento equivocado? Cámbialo gratis Dentro de los 14 días posteriores a la compra y antes de descargarlo, puedes elegir otro documento. Puedes gastar el importe de nuevo.
Escrito por estudiantes que aprobaron
Inmediatamente disponible después del pago
Leer en línea o como PDF

Seller avatar
Los indicadores de reputación están sujetos a la cantidad de artículos vendidos por una tarifa y las reseñas que ha recibido por esos documentos. Hay tres niveles: Bronce, Plata y Oro. Cuanto mayor reputación, más podrás confiar en la calidad del trabajo del vendedor.
SARAHnkalu
4.6
(7)
Vendido
49
Seguidores
0
Artículos
7968
Última venta
1 día hace



Por qué los estudiantes eligen Stuvia

Creado por compañeros estudiantes, verificado por reseñas

Calidad en la que puedes confiar: escrito por estudiantes que aprobaron y evaluado por otros que han usado estos resúmenes.

¿No estás satisfecho? Elige otro documento

¡No te preocupes! Puedes elegir directamente otro documento que se ajuste mejor a lo que buscas.

Paga como quieras, empieza a estudiar al instante

Sin suscripción, sin compromisos. Paga como estés acostumbrado con tarjeta de crédito y descarga tu documento PDF inmediatamente.

Student with book image

“Comprado, descargado y aprobado. Así de fácil puede ser.”

Alisha Student

Preguntas frecuentes

Ups! No podemos cargar tu documento ahora. Inténtalo de nuevo o contacta con soporte.