MK1 SWE STUDY GUIDE EXPECTED
QUESTIONS WITH VERIFIED ANSWERS
• Deglazing old liners method -✓✓Honing
• L/O oxidation doubles every how many degrees above 165°F -✓✓18°F
• Frequency of jacket water testing -✓✓Monthly
• Exhaust hoses service life recommendation -✓✓5 years; whichever is
less
• Type of funding used for DESA -✓✓45 funds
• What gauge calibration sticker is RED? -✓✓Rejected
• Battery fill level above separator plates -✓✓3/8" above the plates.
• Total resistance on a good CAN buss -✓✓60 ohms.
• SEP acronym -✓✓Severity, Probability, Exposure (COMDTINST
3500.3, Enclosure 1, Page 4).
• Most resistant O-ring type to petroleum -✓✓Buna-S
• Emulsification -✓✓What term describes the condition when a fluid has
exceeded its water saturation level?
• Normal operations for rigging are not to exceed what parameters? -
✓✓100%.
• Boat record keeping in modernized unit -✓✓Electronic Asset Logbook
(EAL)
,• Bimetallic thermometer range -✓✓- 40 to 750 degrees
• Maximum water temperature through BA-1 sensing module -
✓✓130°F.
• What should shore tie plates state? -✓✓System voltage, current rating,
and phase rotation.
• Maximum pressure on a Life Stream R/O -✓✓1000 psi.
• When installing a valve what position should the stem be in? -
✓✓Straight up
• Brands allowed on the body -✓✓No more than one brand, with a
maximum size of 4" x 4".
• When should stainless steel air receivers be hydrostatically tested? -
✓✓15 years
• 0.02 PPM for 15 minutes or 0.02 PPM for 30 minutes. -✓✓What
should the chlorine levels be for potable water from a shore tie?
• Condition of gaseous refrigerant with boiling liquid -✓✓Saturated.
• Batteries gas production -✓✓Hydrogen sulfide
• What movement does a thrust bearing prevent? -✓✓Axial and radial.
• Number of articles in the code of conduct -✓✓6
• Wet and dry bulb thermometer -✓✓Determines humidity.
,• What are the different types of oil strainers? -✓✓Simplex/duplex or
mechanical/magnetic.
• Fuel not approved for Coast Guard use -✓✓Biodiesel.
• Major contributors to exhaust smoke emissions -✓✓Piston rings,
cylinder liners, and valve guides.
• On a 45 RBM what is the torque value on the steering cable? -✓✓No
torque value. Do not overtighten.
• Effect of temperature difference between two bodies -✓✓Heat transfer.
• Adobe Acrobat -✓✓In CG-LIMS what is the format of most CG tech
pubs?
• Prussian blue -✓✓Which material is applied to gear teeth to obtain a
static contact reading?
• Solid to vapor state change -✓✓Sublimation.
• Maximum feed-water pressure for a Life Stream RO -✓✓20 psi
• Standard cut of reduction gear teeth -✓✓Helical
• What act established the National Response Center 1-<phone>? -
✓✓Clean water act
• Line shaft bearings alternative name -✓✓Spring bearings.
• What appears as a search result on FEDLOG? -✓✓View screen
, • Cause of crankcase explosion with no other signs -✓✓Cracked or
blown piston.
• 200% of working pressure -✓✓What do you hydro test hydraulic hoses
to?
• Underground tanks capacity requirement -✓✓110% for 72 hours
• Discrepancy type for 40psi in TANB trailer tire -✓✓Restrictive
• Electric actuator testing requirement -✓✓Amps
• Total voltage for four 6V batteries in parallel -✓✓6 volts.
• P100 horsepower -✓✓10 HP
• Design temperature of a freeze box -✓✓0°F.
• Metered -✓✓Combustion required for satisfactory engine operations is
obtained by injector under pressure of a small quantity of accurately
timed ___ and finely atomized fuel oil into the combustion chamber.
• In parallel. -✓✓When using a clamp-type ammeter, how should the
leads be positioned?
• Validity period of a Gas Free certificate -✓✓24 hours
• Between the tank and the filter -✓✓In a fuel system, between which
two components is the fuel strainer typically located?
• What picks up heat from the space to cool the coils? -✓✓Fan coil
QUESTIONS WITH VERIFIED ANSWERS
• Deglazing old liners method -✓✓Honing
• L/O oxidation doubles every how many degrees above 165°F -✓✓18°F
• Frequency of jacket water testing -✓✓Monthly
• Exhaust hoses service life recommendation -✓✓5 years; whichever is
less
• Type of funding used for DESA -✓✓45 funds
• What gauge calibration sticker is RED? -✓✓Rejected
• Battery fill level above separator plates -✓✓3/8" above the plates.
• Total resistance on a good CAN buss -✓✓60 ohms.
• SEP acronym -✓✓Severity, Probability, Exposure (COMDTINST
3500.3, Enclosure 1, Page 4).
• Most resistant O-ring type to petroleum -✓✓Buna-S
• Emulsification -✓✓What term describes the condition when a fluid has
exceeded its water saturation level?
• Normal operations for rigging are not to exceed what parameters? -
✓✓100%.
• Boat record keeping in modernized unit -✓✓Electronic Asset Logbook
(EAL)
,• Bimetallic thermometer range -✓✓- 40 to 750 degrees
• Maximum water temperature through BA-1 sensing module -
✓✓130°F.
• What should shore tie plates state? -✓✓System voltage, current rating,
and phase rotation.
• Maximum pressure on a Life Stream R/O -✓✓1000 psi.
• When installing a valve what position should the stem be in? -
✓✓Straight up
• Brands allowed on the body -✓✓No more than one brand, with a
maximum size of 4" x 4".
• When should stainless steel air receivers be hydrostatically tested? -
✓✓15 years
• 0.02 PPM for 15 minutes or 0.02 PPM for 30 minutes. -✓✓What
should the chlorine levels be for potable water from a shore tie?
• Condition of gaseous refrigerant with boiling liquid -✓✓Saturated.
• Batteries gas production -✓✓Hydrogen sulfide
• What movement does a thrust bearing prevent? -✓✓Axial and radial.
• Number of articles in the code of conduct -✓✓6
• Wet and dry bulb thermometer -✓✓Determines humidity.
,• What are the different types of oil strainers? -✓✓Simplex/duplex or
mechanical/magnetic.
• Fuel not approved for Coast Guard use -✓✓Biodiesel.
• Major contributors to exhaust smoke emissions -✓✓Piston rings,
cylinder liners, and valve guides.
• On a 45 RBM what is the torque value on the steering cable? -✓✓No
torque value. Do not overtighten.
• Effect of temperature difference between two bodies -✓✓Heat transfer.
• Adobe Acrobat -✓✓In CG-LIMS what is the format of most CG tech
pubs?
• Prussian blue -✓✓Which material is applied to gear teeth to obtain a
static contact reading?
• Solid to vapor state change -✓✓Sublimation.
• Maximum feed-water pressure for a Life Stream RO -✓✓20 psi
• Standard cut of reduction gear teeth -✓✓Helical
• What act established the National Response Center 1-<phone>? -
✓✓Clean water act
• Line shaft bearings alternative name -✓✓Spring bearings.
• What appears as a search result on FEDLOG? -✓✓View screen
, • Cause of crankcase explosion with no other signs -✓✓Cracked or
blown piston.
• 200% of working pressure -✓✓What do you hydro test hydraulic hoses
to?
• Underground tanks capacity requirement -✓✓110% for 72 hours
• Discrepancy type for 40psi in TANB trailer tire -✓✓Restrictive
• Electric actuator testing requirement -✓✓Amps
• Total voltage for four 6V batteries in parallel -✓✓6 volts.
• P100 horsepower -✓✓10 HP
• Design temperature of a freeze box -✓✓0°F.
• Metered -✓✓Combustion required for satisfactory engine operations is
obtained by injector under pressure of a small quantity of accurately
timed ___ and finely atomized fuel oil into the combustion chamber.
• In parallel. -✓✓When using a clamp-type ammeter, how should the
leads be positioned?
• Validity period of a Gas Free certificate -✓✓24 hours
• Between the tank and the filter -✓✓In a fuel system, between which
two components is the fuel strainer typically located?
• What picks up heat from the space to cool the coils? -✓✓Fan coil
