IPC A 610 Questions with Correct Solutions
Question:
1. Class 1 Product
Answer:
General Electronics Product - includes products where the major requirement is function of
the completed assembly.
Question:
2. Class 2 Product
Answer:
Dedicated Service Electronic Product - Continued performance and extended life required.
Uninterrupted service is desired but not required.
Question:
3. Class 3 Product
Answer:
High Performance Electrical Product - Continued high performance or
performance-on-demand is critical. Equipment downtime cannot be tolerated. Equipment
might be used for life-support or other critical systems.
Question:
4. Who as the ultimate responsibility for identifying the class to which the assembly is
evaluated?
Answer:
The Customer.
Question:
5. Shall
Answer:
Invokes a requirement for manufacturers of all classes or product, and failure to comply with
the requirement is a noncompliance to this standard.
Question:
6. Order of Precedence in event of conflict 1
Answer:
1. Procurement as agreed and documented between customer and supplier.
, Question:
7. Order of Precedence in event of conflict 2
Answer:
Master drawing or master ass. drawing reflecting the customer's detailed requirements.
Question:
8. Order of Precedence in event of conflict 3
Answer:
IPC-1-610 when invoked by the customer or contract.
Question:
9. If documents other than IPC-A-610 are cited, the order of precedence shall be defined in
the _
Answer:
Procurement documents
Question:
10. Target Condition
Answer:
A condition that is close to perfect, but is not always achievable and may not be necessary to
ensure the reliability of the assembly.
Question:
11. Acceptable Condition
Answer:
A condition that, while not necessarily perfect, will maintain integrity and reliability of the
assembly
Question:
12. Defect Condition
Answer:
The form, fit or function of the assembly is inadequate for use in its end use environment.
Question:
13. A defect for Class 1...
Answer:
automatically implies a defect for Class 2 and 3. A defect for Class 2 implies a defect for Class
3.
Question:
1. Class 1 Product
Answer:
General Electronics Product - includes products where the major requirement is function of
the completed assembly.
Question:
2. Class 2 Product
Answer:
Dedicated Service Electronic Product - Continued performance and extended life required.
Uninterrupted service is desired but not required.
Question:
3. Class 3 Product
Answer:
High Performance Electrical Product - Continued high performance or
performance-on-demand is critical. Equipment downtime cannot be tolerated. Equipment
might be used for life-support or other critical systems.
Question:
4. Who as the ultimate responsibility for identifying the class to which the assembly is
evaluated?
Answer:
The Customer.
Question:
5. Shall
Answer:
Invokes a requirement for manufacturers of all classes or product, and failure to comply with
the requirement is a noncompliance to this standard.
Question:
6. Order of Precedence in event of conflict 1
Answer:
1. Procurement as agreed and documented between customer and supplier.
, Question:
7. Order of Precedence in event of conflict 2
Answer:
Master drawing or master ass. drawing reflecting the customer's detailed requirements.
Question:
8. Order of Precedence in event of conflict 3
Answer:
IPC-1-610 when invoked by the customer or contract.
Question:
9. If documents other than IPC-A-610 are cited, the order of precedence shall be defined in
the _
Answer:
Procurement documents
Question:
10. Target Condition
Answer:
A condition that is close to perfect, but is not always achievable and may not be necessary to
ensure the reliability of the assembly.
Question:
11. Acceptable Condition
Answer:
A condition that, while not necessarily perfect, will maintain integrity and reliability of the
assembly
Question:
12. Defect Condition
Answer:
The form, fit or function of the assembly is inadequate for use in its end use environment.
Question:
13. A defect for Class 1...
Answer:
automatically implies a defect for Class 2 and 3. A defect for Class 2 implies a defect for Class
3.
