Ase Brakes A5 Test Exams 1, 2, And 3 | All Questions And Correct Answers |
Already Graded A+ | Verified Answers | Latest Version 2024
A restricted brake hose on the right side. - (CORRECT ANSWER)A vehicle pulls to the right after the brake
pedal is released. This could be caused by:
A. A restricted brake hose on the right side.
B. A faulty metering valve.
C. A cut master cylinder piston seal.
D. A restricted brake hose on the left side.
Neither A nor B - (CORRECT ANSWER)Technician A says that brake drag can be caused by a seized star
wheel adjuster. Technician B says that brake drag can be caused by worn drums. Who is correct?
A. Technician A only
B. Technician B only
C. Technician A and B
D. Neither A nor B
Brake light switch - (CORRECT ANSWER)Which of the following would typically proved an input to the
ABS control module?
A. Power steering pressure switch
B. Pressure differential switch
C. PRNDL switch
D. Brake light switch
Leaking master cylinder - (CORRECT ANSWER)With the engine running, the brake pedal is low and soft.
Brake fluid level is low in the primary reservoir. Which of the following would be the most likely cause?
A. Leaking master cylinder
B. A bypassing master cylinder
C. Stuck open vacuum check valve
D. Restricted vacuum
1
, Technician A only - (CORRECT ANSWER)A brake line needs to be replaced. Technician A says a new line
should be installed using a double flare or ISO. Technician B says a new section should be installed with
compression fittings. Who is right?
A. Technician A only
B. Technician B only
C. Technician A and B
D. Neither A nor B
The final check should be with a dial indicator - (CORRECT ANSWER)A set of tapered roller bearings are
being serviced. Which of the following is true regarding the tightening process?
A. Tighten the nut to spec and back off one turn
B. Tighten the nut to 100 ft Ibs.
C. Tires must be on the ground and the full weight of the car on the suspension
D. The final check should be with a dial indicator
Technician B only - (CORRECT ANSWER)Technician A says a defective brake switch can cause a faulty
wheel speed signal. Technician B says this can be caused by rust. Who is correct?
A. Technician A only
B. Technician B only
C. Technician A and B
D. Neither A nor B
Air in the brake fluid - (CORRECT ANSWER)A vehicle equipped with a hydro-boost system has a low, soft
pedal and poor brake performance. Which of these could be the cause?
A. Air in the power steering fluid
B. Weak or defective power steering pump
C. Air in the brake fluid
2
Already Graded A+ | Verified Answers | Latest Version 2024
A restricted brake hose on the right side. - (CORRECT ANSWER)A vehicle pulls to the right after the brake
pedal is released. This could be caused by:
A. A restricted brake hose on the right side.
B. A faulty metering valve.
C. A cut master cylinder piston seal.
D. A restricted brake hose on the left side.
Neither A nor B - (CORRECT ANSWER)Technician A says that brake drag can be caused by a seized star
wheel adjuster. Technician B says that brake drag can be caused by worn drums. Who is correct?
A. Technician A only
B. Technician B only
C. Technician A and B
D. Neither A nor B
Brake light switch - (CORRECT ANSWER)Which of the following would typically proved an input to the
ABS control module?
A. Power steering pressure switch
B. Pressure differential switch
C. PRNDL switch
D. Brake light switch
Leaking master cylinder - (CORRECT ANSWER)With the engine running, the brake pedal is low and soft.
Brake fluid level is low in the primary reservoir. Which of the following would be the most likely cause?
A. Leaking master cylinder
B. A bypassing master cylinder
C. Stuck open vacuum check valve
D. Restricted vacuum
1
, Technician A only - (CORRECT ANSWER)A brake line needs to be replaced. Technician A says a new line
should be installed using a double flare or ISO. Technician B says a new section should be installed with
compression fittings. Who is right?
A. Technician A only
B. Technician B only
C. Technician A and B
D. Neither A nor B
The final check should be with a dial indicator - (CORRECT ANSWER)A set of tapered roller bearings are
being serviced. Which of the following is true regarding the tightening process?
A. Tighten the nut to spec and back off one turn
B. Tighten the nut to 100 ft Ibs.
C. Tires must be on the ground and the full weight of the car on the suspension
D. The final check should be with a dial indicator
Technician B only - (CORRECT ANSWER)Technician A says a defective brake switch can cause a faulty
wheel speed signal. Technician B says this can be caused by rust. Who is correct?
A. Technician A only
B. Technician B only
C. Technician A and B
D. Neither A nor B
Air in the brake fluid - (CORRECT ANSWER)A vehicle equipped with a hydro-boost system has a low, soft
pedal and poor brake performance. Which of these could be the cause?
A. Air in the power steering fluid
B. Weak or defective power steering pump
C. Air in the brake fluid
2
