Nccer Pipefitter Test | All Questions And Correct Answers | Latest Version |
Verified Answers | Graded A+ (Just Released)
Convert 1/4 to its decimal equivalent.
A) .01
B) .25
C) 0.4
D) 0.5 - (CORRECT ANSWER)B
Piping that is field-routed to a pump must be supported
A) Off the pump suction
B) Diagonally
C) Independently
D) Off the pump discharge - (CORRECT ANSWER)C
What is used when lighting a cutting torch ?
A) Striker
B) Cigarette lighter
C) Match
D) Any open flame - (CORRECT ANSWER)A
Where is specific information needed to install piping and associated items found ?
A) Reliability network
B) Owner of the company
C) Material Manufacturer
D) Standards and Specifications - (CORRECT ANSWER)D
Damaged and broken tools should be
1
,A) Used if possible
B) Kept for backup
C) Taken out of Service
D) Used for minor tasks - (CORRECT ANSWER)C
What is the ID of 10'' schedule 80 piping.
A) 9 3/16
B) 9 5/16
C) 9 9/16
D) 10 1/16 - (CORRECT ANSWER)C
The two steps in making up threaded joints are the hand engagement and
A) Machine makeup
B) Wrench makeup
C) Driver makeup - (CORRECT ANSWER)B
Which of the following actions should be taken before a hydrostatic test is performed ?
A) Remove pressure relief valves
B) Leave control mechanisms in place
C) Leave orifice flanges in place
D) Remove blinds - (CORRECT ANSWER)a
A 4-inch lateral riser is to be fabricated for a 6-inch pipe. How many ordinate lines will
be needed to lay out this cut ?
A) 32
2
, B) 16
C) 8
D) 4 - (CORRECT ANSWER)C
Who is qualified to repair power tools.
A) Journey person
B) Competent Technician
C) Electrician
D) Tool crib attendant - (CORRECT ANSWER)B
Which of the following plastic pipes is NOT joined by solvent welding ?
A) PVC
B) HDPE
C) CPVC
D) ABS - (CORRECT ANSWER)B
Material placed in the bottom of the trench under the pipe to provide support is called.
A) Heave
B) Sub trench
C) Trench load
D) Bedding - (CORRECT ANSWER)D
Socket weld joints have a gap between the end of the pipe and the bottom of the
socket. What is the purpose of this gap ?
A) Makes assembly easier
3
Verified Answers | Graded A+ (Just Released)
Convert 1/4 to its decimal equivalent.
A) .01
B) .25
C) 0.4
D) 0.5 - (CORRECT ANSWER)B
Piping that is field-routed to a pump must be supported
A) Off the pump suction
B) Diagonally
C) Independently
D) Off the pump discharge - (CORRECT ANSWER)C
What is used when lighting a cutting torch ?
A) Striker
B) Cigarette lighter
C) Match
D) Any open flame - (CORRECT ANSWER)A
Where is specific information needed to install piping and associated items found ?
A) Reliability network
B) Owner of the company
C) Material Manufacturer
D) Standards and Specifications - (CORRECT ANSWER)D
Damaged and broken tools should be
1
,A) Used if possible
B) Kept for backup
C) Taken out of Service
D) Used for minor tasks - (CORRECT ANSWER)C
What is the ID of 10'' schedule 80 piping.
A) 9 3/16
B) 9 5/16
C) 9 9/16
D) 10 1/16 - (CORRECT ANSWER)C
The two steps in making up threaded joints are the hand engagement and
A) Machine makeup
B) Wrench makeup
C) Driver makeup - (CORRECT ANSWER)B
Which of the following actions should be taken before a hydrostatic test is performed ?
A) Remove pressure relief valves
B) Leave control mechanisms in place
C) Leave orifice flanges in place
D) Remove blinds - (CORRECT ANSWER)a
A 4-inch lateral riser is to be fabricated for a 6-inch pipe. How many ordinate lines will
be needed to lay out this cut ?
A) 32
2
, B) 16
C) 8
D) 4 - (CORRECT ANSWER)C
Who is qualified to repair power tools.
A) Journey person
B) Competent Technician
C) Electrician
D) Tool crib attendant - (CORRECT ANSWER)B
Which of the following plastic pipes is NOT joined by solvent welding ?
A) PVC
B) HDPE
C) CPVC
D) ABS - (CORRECT ANSWER)B
Material placed in the bottom of the trench under the pipe to provide support is called.
A) Heave
B) Sub trench
C) Trench load
D) Bedding - (CORRECT ANSWER)D
Socket weld joints have a gap between the end of the pipe and the bottom of the
socket. What is the purpose of this gap ?
A) Makes assembly easier
3
