AMMO 112 ACTUAL TEST PAPER
QUESTIONS AND ANSWERS VERIFIED
REVIEW
●● The purpose of cutting lubricant in most drilling ops is to increase
the
Answer: Drilling speed and drill bit life
●● Minimum protection using a bench grinder
Answer: eye and face protection
●● what condition would prevent an operator from applying power to a
hoist or other powered lifting device
Answer: an AF Form 979
●● most common type of lifting sling
Answer: wire rope
●● the enunciators displayed on the fluke 8025 series multimeter are
used to distinguish among
Answer: ohms, kilohm, and megohms
,●● 2 operational modes of the Fluke 8025
Answer: range and hold
●● the steering system on the MHU 141/ M trailer has a turning radius
of how many inches
Answer: 200
●● When the MHU 141 trailer is loaded or towed with the hinged deck
panels open, what must be done?
Answer: the deck supports must be properly positioned and locked in
place with quick release pins
●● Max load capacity of the MHU 110/ M trailer
Answer: 15,000
●● the parking brake on the MHU 110/ M is applied by
Answer: pulling either one of two hand levers located on each side of the
front of trailer
●● how many openings are on the deck of the MHU- 226 trailer
Answer: 3
●● what type of steering aids the MHU- 226
,Answer: four wheeled double ackerman
●● After 463L pallets are positioned on a rollerized trailer, what can you
use to secure the pallets
Answer: MB-1 chain assemblies and or tie down straps
●● what kind of movements supports on base activities to or from the
flightline
Answer: operational
●● what munitions item is not loaded into transport modules by
munitions personnel
Answer: 20 mm
●● what transport module used for decoy munitions has a max capacity
of 30 magazines
Answer: ALE- 50
●● How often should the positive locking devices on the doors of
munitions transport modules be checked
Answer: after loading, unloading and periodically between stops
●● the purpose of the transport beam beneath the lift arm assemblies on
the MJ- 1 series lift truck is to
, Answer: provide added support and to relieve hydraulic pressure from
the lift arms when carrying loads for long distances
●● Lifting capacity of the MJ 1 series lift truck
Answer: 3,000
●● Lifting capacity of MHU 83 lift truck
Answer: 7,000
●● When using fork adapters on MHU 83 series lift truck
Answer: it reduces lifting capacity by 1,000
●● What happens when you release the accelerator pedal on a vehicle
driven with a hydrostatic transmission
Answer: the unit coasts to a stop very quickly
●● what is the primary drawback to using the hydraulic hand pump to
build hydraulic pressure on the MHU 83 lift truck
Answer: extremely slow way to build hydraulic pressure
●● How is the yaw positioning from the cradle or boom controls of an
MJ 1 lift truck adjusted
Answer: Manually
QUESTIONS AND ANSWERS VERIFIED
REVIEW
●● The purpose of cutting lubricant in most drilling ops is to increase
the
Answer: Drilling speed and drill bit life
●● Minimum protection using a bench grinder
Answer: eye and face protection
●● what condition would prevent an operator from applying power to a
hoist or other powered lifting device
Answer: an AF Form 979
●● most common type of lifting sling
Answer: wire rope
●● the enunciators displayed on the fluke 8025 series multimeter are
used to distinguish among
Answer: ohms, kilohm, and megohms
,●● 2 operational modes of the Fluke 8025
Answer: range and hold
●● the steering system on the MHU 141/ M trailer has a turning radius
of how many inches
Answer: 200
●● When the MHU 141 trailer is loaded or towed with the hinged deck
panels open, what must be done?
Answer: the deck supports must be properly positioned and locked in
place with quick release pins
●● Max load capacity of the MHU 110/ M trailer
Answer: 15,000
●● the parking brake on the MHU 110/ M is applied by
Answer: pulling either one of two hand levers located on each side of the
front of trailer
●● how many openings are on the deck of the MHU- 226 trailer
Answer: 3
●● what type of steering aids the MHU- 226
,Answer: four wheeled double ackerman
●● After 463L pallets are positioned on a rollerized trailer, what can you
use to secure the pallets
Answer: MB-1 chain assemblies and or tie down straps
●● what kind of movements supports on base activities to or from the
flightline
Answer: operational
●● what munitions item is not loaded into transport modules by
munitions personnel
Answer: 20 mm
●● what transport module used for decoy munitions has a max capacity
of 30 magazines
Answer: ALE- 50
●● How often should the positive locking devices on the doors of
munitions transport modules be checked
Answer: after loading, unloading and periodically between stops
●● the purpose of the transport beam beneath the lift arm assemblies on
the MJ- 1 series lift truck is to
, Answer: provide added support and to relieve hydraulic pressure from
the lift arms when carrying loads for long distances
●● Lifting capacity of the MJ 1 series lift truck
Answer: 3,000
●● Lifting capacity of MHU 83 lift truck
Answer: 7,000
●● When using fork adapters on MHU 83 series lift truck
Answer: it reduces lifting capacity by 1,000
●● What happens when you release the accelerator pedal on a vehicle
driven with a hydrostatic transmission
Answer: the unit coasts to a stop very quickly
●● what is the primary drawback to using the hydraulic hand pump to
build hydraulic pressure on the MHU 83 lift truck
Answer: extremely slow way to build hydraulic pressure
●● How is the yaw positioning from the cradle or boom controls of an
MJ 1 lift truck adjusted
Answer: Manually
