CIP Level 1 NACE-CIP1-001 Practice Test Questions with Verified
Answers (Correct Update)
Question 1: CIP Level 1 NACE-CIP1-001 Practice Test
Answer:
Question 2: How to Become a Coating Inspector
Answer: To become a coating inspector, complete the Coating Inspector Program (CIP) offered by
NACE International. There are two levels of certification. The CIP level 1 certification is for
inspectors who perform basic, non-destructive inspections. Obtain this certification by completing the
required NACE exams. CIP level 2 certification requires two years of experience in the field, as well
as completion of the NACE exams.
Question 3: CIP Level 1 NACE-CIP1-001 - Coatings Inspector Program Level 1
Answer: CIP Level 1 covers the technical and practical fundamentals of coating inspection work.
Students will be prepared to perform basic coating inspections using non-destructive techniques and
instrumentation. Passcert provides students valid CIP Level 1 NACE-CIP1-001 dumps with
knowledge and application of coating materials, along with techniques for surface preparation.
Question 4: You are the NACE Inspector on a tank lining project where a 50% solids epoxy
tank lining is being applied. After application of the 19 coat you notice small blisters in some
areas of the applied lining. Your FIRST preferred course of action is to:
Answer: A. Break the blisters to see what's inside B. Document the problem and advise the Contractor
and Owner's representative C. Document the problem and advise the Contractor D. Extract any liquid
that may be inside the blister and send it to the lab for further analysis Answer: B
Question 5: .Dew point is the temperature at which
Answer: A. water freezes. B. humidity decreases C. condensation occurs. D. the air is saturated.
Answer: C
Question 6: If a contractor is using a poorly maintained compressor to supply air for abrasive
blast cleaning and conventional airspray, the coating inspector should perform a
Answer: A. dry film thickness (DEI) measurement. B. wet film thickness (WFT) measurement. C.
blotter test for the presence of oil and water. D. vial lest. Answer: C
Page 1
Answers (Correct Update)
Question 1: CIP Level 1 NACE-CIP1-001 Practice Test
Answer:
Question 2: How to Become a Coating Inspector
Answer: To become a coating inspector, complete the Coating Inspector Program (CIP) offered by
NACE International. There are two levels of certification. The CIP level 1 certification is for
inspectors who perform basic, non-destructive inspections. Obtain this certification by completing the
required NACE exams. CIP level 2 certification requires two years of experience in the field, as well
as completion of the NACE exams.
Question 3: CIP Level 1 NACE-CIP1-001 - Coatings Inspector Program Level 1
Answer: CIP Level 1 covers the technical and practical fundamentals of coating inspection work.
Students will be prepared to perform basic coating inspections using non-destructive techniques and
instrumentation. Passcert provides students valid CIP Level 1 NACE-CIP1-001 dumps with
knowledge and application of coating materials, along with techniques for surface preparation.
Question 4: You are the NACE Inspector on a tank lining project where a 50% solids epoxy
tank lining is being applied. After application of the 19 coat you notice small blisters in some
areas of the applied lining. Your FIRST preferred course of action is to:
Answer: A. Break the blisters to see what's inside B. Document the problem and advise the Contractor
and Owner's representative C. Document the problem and advise the Contractor D. Extract any liquid
that may be inside the blister and send it to the lab for further analysis Answer: B
Question 5: .Dew point is the temperature at which
Answer: A. water freezes. B. humidity decreases C. condensation occurs. D. the air is saturated.
Answer: C
Question 6: If a contractor is using a poorly maintained compressor to supply air for abrasive
blast cleaning and conventional airspray, the coating inspector should perform a
Answer: A. dry film thickness (DEI) measurement. B. wet film thickness (WFT) measurement. C.
blotter test for the presence of oil and water. D. vial lest. Answer: C
Page 1
