ERAILSAFE EXAM SCRIPT TESTED
QUESTIONS FULL SOLUTION PREMIUM
STUDY MATERIAL
●● A(n) __________________ is any man-made cut, cavity, trench, or
depression in an earth surface, formed by removing earth.
Answer: Excavation
●● A(n)_____________ identifies unsanitary, hazardous, or dangerous
working conditions and has the authority to correct or eliminate them.
Answer: Competent person
●● A(n) _________ is large enough to work in but has limited means of
entry or exit.
Answer: Confined space
●● Liquids that are _______ must be stored in safety cans to avoid the
risk of fire.
Answer: Flammable
●● To save lives, prevent injuries, and protect the health of America's
workers, _________ publishes rules and regulations that employees
must follow.
,Answer: Occupational Safety and Health Administration
●● Even a brief exposure to the ultraviolet light from arc welding can
damage the eyes, causing a(n) __________.
Answer: Flash burn
●● ___________is an OSHA rule requiring all contractors to educate
their employees about the hazardous chemicals they may be exposed to
on the job site.
Answer: HAZCOM (Hazard Communication Standard)
●● The temperature at which a fuel gives off enough gases to burn is
called the __________.
Answer: Flash point
●● A(n) ___________ is the conducting connection between electrical
equipment or an electrical circuit and the earth.
Answer: Ground
●● When climbing a ladder or scaffold, a tagline or _________ should
be used to pull up tools.
Answer: Hand line
, ●● If a work area is ___________, that means it has pieces of material at
least 2 inches (5cm) thick and 6 inches (15cm) wide used as flooring,
decking, or scaffolds.
Answer: Planked
●● When doing work more than 6 feet (2m) above the ground, a worker
must wear a safety harness with a(n) _____________ that is attached to
a strong anchor point.
Answer: Lanyard
●● A structure that prevents trench walls from collapsing is known as
__________.
Answer: Shoring
●● Information on how to handle hazardous substances is located in the
_____________.
Answer: Safety data sheet (SDS)
●● Overloading, which means exceeding the ____________ of a ladder,
can cause ladder failure.
Answer: Maximum intended load
●● If you are operating a vehicle on a job site and cannot see to your
rear, get a(n) __________ to direct you.
QUESTIONS FULL SOLUTION PREMIUM
STUDY MATERIAL
●● A(n) __________________ is any man-made cut, cavity, trench, or
depression in an earth surface, formed by removing earth.
Answer: Excavation
●● A(n)_____________ identifies unsanitary, hazardous, or dangerous
working conditions and has the authority to correct or eliminate them.
Answer: Competent person
●● A(n) _________ is large enough to work in but has limited means of
entry or exit.
Answer: Confined space
●● Liquids that are _______ must be stored in safety cans to avoid the
risk of fire.
Answer: Flammable
●● To save lives, prevent injuries, and protect the health of America's
workers, _________ publishes rules and regulations that employees
must follow.
,Answer: Occupational Safety and Health Administration
●● Even a brief exposure to the ultraviolet light from arc welding can
damage the eyes, causing a(n) __________.
Answer: Flash burn
●● ___________is an OSHA rule requiring all contractors to educate
their employees about the hazardous chemicals they may be exposed to
on the job site.
Answer: HAZCOM (Hazard Communication Standard)
●● The temperature at which a fuel gives off enough gases to burn is
called the __________.
Answer: Flash point
●● A(n) ___________ is the conducting connection between electrical
equipment or an electrical circuit and the earth.
Answer: Ground
●● When climbing a ladder or scaffold, a tagline or _________ should
be used to pull up tools.
Answer: Hand line
, ●● If a work area is ___________, that means it has pieces of material at
least 2 inches (5cm) thick and 6 inches (15cm) wide used as flooring,
decking, or scaffolds.
Answer: Planked
●● When doing work more than 6 feet (2m) above the ground, a worker
must wear a safety harness with a(n) _____________ that is attached to
a strong anchor point.
Answer: Lanyard
●● A structure that prevents trench walls from collapsing is known as
__________.
Answer: Shoring
●● Information on how to handle hazardous substances is located in the
_____________.
Answer: Safety data sheet (SDS)
●● Overloading, which means exceeding the ____________ of a ladder,
can cause ladder failure.
Answer: Maximum intended load
●● If you are operating a vehicle on a job site and cannot see to your
rear, get a(n) __________ to direct you.
