Insulation NCCR
Insulation NCCR
Study online at https://quizlet.com/_a23psz
1. Calcium silicate sodium silicate-based adhesive (such as CP-97) for fabricating fitting
covers should be used for
2. 16-22 gauge metal sheets Subgirts are usually fabricated frim
3. 3 o'clock to 4 o'clock Unless otherwise specified, longitudinal laps on jacketing should be
in what position?
4. Stagger the insulation What will an insulator normally do when starting to insulate piping?
5. Vapor sealed Any piping that operates at a temperature lower than ambient air must
be
6. Metal gores Jacketing used on a pipe bend or sweep would require
7. 36 feet If a drawing is scaled at 1/8" = 1ft and the distance on the drawing
measures 3in how many feel will it equal?
8. Sealing cold application Mineral wool is used for
insulation
9. Guards What is required to be in place on all stationary power tools
10. 140 How many 3ft long sections of pipe insulation be required to insulate
240ft of pipe?
11. Center to center of welds Where are miters started on a welded elbow?
12. A-tape What type of tape is used to wrap steam tracing
13. At the termination of the Where should a bevel cap be used for
top of the vertical pipe in-
sulation
14.
1/7
, Insulation NCCR
Insulation NCCR
Study online at https://quizlet.com/_a23psz
Temporary hold insula- Which of the following is a common use of rubber bands made from
tion in place inner tubes
15. Watertightness Neoprene washers are used with sheet metal and lagging to provide
16. an unsafe condition an insulator, inspecting the work area finds materials left in the walk
way on the work platform. these materials represent:
17. determine the circumfer- one step required in the take off when a head gore is laid out is to
ence
18. rigid isulation what should the top of ducks or equipment that are subject to foot
traffic be insulated with
19. metal shears what does this diagram represent
20. snips what tool should be used to cut metal lath or chicken wire mesh
21. 18 inches when insulating a vessel or tank with calcium silicate at what length
should you cut your stagger to start
22. mineral wool what type of insulation is used on boilers
23. clean the surface to bare what must be done to a surface before pins are welded
metal
24. Pittsburg seam manway covers and exchangers heads may be covered with jacketing
material by the combined use of an end cap with
25. any qualified equipment other than who is authorized to remove the tag or lock placed on a
operator piece of equipment
26. before mastic cap is in- unless otherwise specified, valves and flangers on cold services insu-
stalled lation should be installed
2/7
Insulation NCCR
Study online at https://quizlet.com/_a23psz
1. Calcium silicate sodium silicate-based adhesive (such as CP-97) for fabricating fitting
covers should be used for
2. 16-22 gauge metal sheets Subgirts are usually fabricated frim
3. 3 o'clock to 4 o'clock Unless otherwise specified, longitudinal laps on jacketing should be
in what position?
4. Stagger the insulation What will an insulator normally do when starting to insulate piping?
5. Vapor sealed Any piping that operates at a temperature lower than ambient air must
be
6. Metal gores Jacketing used on a pipe bend or sweep would require
7. 36 feet If a drawing is scaled at 1/8" = 1ft and the distance on the drawing
measures 3in how many feel will it equal?
8. Sealing cold application Mineral wool is used for
insulation
9. Guards What is required to be in place on all stationary power tools
10. 140 How many 3ft long sections of pipe insulation be required to insulate
240ft of pipe?
11. Center to center of welds Where are miters started on a welded elbow?
12. A-tape What type of tape is used to wrap steam tracing
13. At the termination of the Where should a bevel cap be used for
top of the vertical pipe in-
sulation
14.
1/7
, Insulation NCCR
Insulation NCCR
Study online at https://quizlet.com/_a23psz
Temporary hold insula- Which of the following is a common use of rubber bands made from
tion in place inner tubes
15. Watertightness Neoprene washers are used with sheet metal and lagging to provide
16. an unsafe condition an insulator, inspecting the work area finds materials left in the walk
way on the work platform. these materials represent:
17. determine the circumfer- one step required in the take off when a head gore is laid out is to
ence
18. rigid isulation what should the top of ducks or equipment that are subject to foot
traffic be insulated with
19. metal shears what does this diagram represent
20. snips what tool should be used to cut metal lath or chicken wire mesh
21. 18 inches when insulating a vessel or tank with calcium silicate at what length
should you cut your stagger to start
22. mineral wool what type of insulation is used on boilers
23. clean the surface to bare what must be done to a surface before pins are welded
metal
24. Pittsburg seam manway covers and exchangers heads may be covered with jacketing
material by the combined use of an end cap with
25. any qualified equipment other than who is authorized to remove the tag or lock placed on a
operator piece of equipment
26. before mastic cap is in- unless otherwise specified, valves and flangers on cold services insu-
stalled lation should be installed
2/7
