Tx NCCER Core Certification
Companies with strong safety cultures usually have lower? - answerTurnover
Poor lighting, excessive noise, and inadequate guards for moving parts are examples of -
answerunsafe conditions
The activity that consists of breaking a job into its component tasks and then analyzing each
step for
potential hazards is called a _____. - answerJob Safety Analysis
A measure of the probability, consequences, and exposure related to an event is referred to
as _____. - answerRisk
If there is a hole in the floor of a structure, the preferred method of protecting workers from
falls is to _____. - answerCover and mark it
The D-ring or support point on a safety harness should be placed _____. - answerBetween
the shoulder blades, middle of your back
A personal fall arrest system should be inspected monthly by a _____. - answerCompetent
person
Lanyards that have no shock-absorbing features are used for _____. - answerPositioning
When placing a ladder against a platform or roof, the top of the ladder should extend above
the point where
the ladder touches the platform or roof by at least _____. - answer3 Feet
When performing overhead work on scaffolding, what protective measures must be taken to
prevent objects
from falling and striking a person below? - answertoe boards, debris nets, or canopies
When stacking materials such as bricks or block, do not stack materials beyond a _____. -
answer4:1 Ratio
Benching systems are prohibited in _____. - answerType C
In the absence of other information, all soil in an excavation should be treated as if it is
_____. - answerType C
Daily inspection of an excavation must be performed by a(n) _____. - answerCompetent
person
One of the most common grounding systems used for protection against accidental electrical
shock is the
_____. - answer3-wire system
, A polarized electrical receptacle is used for _____. - answerdouble insulated tools
A system that protects workers from the release of hazardous energy while they work with
machines and
equipment is referred to as _____. - answerLock-out/ Tag-out
In a lockout/tagout situation, a personal lock and tag must be removed by _____. -
answerPerson who applied them
Hard hats should be made of fiberglass or _____. - answerReinforced plastic
A good general rule about hearing protection is that it should be used if you must raise your
voice for
someone to hear you when they are _____. - answer2 feet away
When there is the potential to be exposed to asbestos, workers must _____. - answeravoid
disturbing it and contact your supervisor
The respirator that would be used where dust or solid particles might be inhaled is a _____. -
answerhalf mask or mouth piece with a mechanical filter
One source of lead on some job sites is _____. - answerPaint
Hepatitis can be caused by contact with _____. - answerBlood
One of the symptoms of heat stroke is _____. - answerExtremely high body temperature
When other workers are working near a welding operation, the standard practice is to
_____. - answerScreen the work area with welding shields
What type of fire extinguisher would be used on an electric motor that has overheated and
caught fire? - answerClass C
The type of permit that must be issued before a permit-required confined space can be
accessed is called a(n)
_____. - answerentry permit
Which rung is the last rung you should stand on on an extension ladder? - answerFourth
from the top
. All work on electrical circuits should be done with circuits - answerde-energized, locked
out, and confirmed
. What should a worker always check before working with or around chemicals - answerSDS
(Safety Data Sheets)
What must be kept away from grease or oil because of the possibility of explosion –
answerOxygen
Companies with strong safety cultures usually have lower? - answerTurnover
Poor lighting, excessive noise, and inadequate guards for moving parts are examples of -
answerunsafe conditions
The activity that consists of breaking a job into its component tasks and then analyzing each
step for
potential hazards is called a _____. - answerJob Safety Analysis
A measure of the probability, consequences, and exposure related to an event is referred to
as _____. - answerRisk
If there is a hole in the floor of a structure, the preferred method of protecting workers from
falls is to _____. - answerCover and mark it
The D-ring or support point on a safety harness should be placed _____. - answerBetween
the shoulder blades, middle of your back
A personal fall arrest system should be inspected monthly by a _____. - answerCompetent
person
Lanyards that have no shock-absorbing features are used for _____. - answerPositioning
When placing a ladder against a platform or roof, the top of the ladder should extend above
the point where
the ladder touches the platform or roof by at least _____. - answer3 Feet
When performing overhead work on scaffolding, what protective measures must be taken to
prevent objects
from falling and striking a person below? - answertoe boards, debris nets, or canopies
When stacking materials such as bricks or block, do not stack materials beyond a _____. -
answer4:1 Ratio
Benching systems are prohibited in _____. - answerType C
In the absence of other information, all soil in an excavation should be treated as if it is
_____. - answerType C
Daily inspection of an excavation must be performed by a(n) _____. - answerCompetent
person
One of the most common grounding systems used for protection against accidental electrical
shock is the
_____. - answer3-wire system
, A polarized electrical receptacle is used for _____. - answerdouble insulated tools
A system that protects workers from the release of hazardous energy while they work with
machines and
equipment is referred to as _____. - answerLock-out/ Tag-out
In a lockout/tagout situation, a personal lock and tag must be removed by _____. -
answerPerson who applied them
Hard hats should be made of fiberglass or _____. - answerReinforced plastic
A good general rule about hearing protection is that it should be used if you must raise your
voice for
someone to hear you when they are _____. - answer2 feet away
When there is the potential to be exposed to asbestos, workers must _____. - answeravoid
disturbing it and contact your supervisor
The respirator that would be used where dust or solid particles might be inhaled is a _____. -
answerhalf mask or mouth piece with a mechanical filter
One source of lead on some job sites is _____. - answerPaint
Hepatitis can be caused by contact with _____. - answerBlood
One of the symptoms of heat stroke is _____. - answerExtremely high body temperature
When other workers are working near a welding operation, the standard practice is to
_____. - answerScreen the work area with welding shields
What type of fire extinguisher would be used on an electric motor that has overheated and
caught fire? - answerClass C
The type of permit that must be issued before a permit-required confined space can be
accessed is called a(n)
_____. - answerentry permit
Which rung is the last rung you should stand on on an extension ladder? - answerFourth
from the top
. All work on electrical circuits should be done with circuits - answerde-energized, locked
out, and confirmed
. What should a worker always check before working with or around chemicals - answerSDS
(Safety Data Sheets)
What must be kept away from grease or oil because of the possibility of explosion –
answerOxygen
