final exam nims
The strongest socket with the highest tightening force is the __________ socket - Answer-6 POINT
is/are used to fill the small gaps between threads to prevent leakage of air, gases, or liquids. - Answer-
Sealants
The __________ the fastener the wrench handle is grasped, the greater the tightening force that can be
applied. - Answer-further away from
A T-Allen wrench is used for what purpose? - Answer-When hand clearance around the bolt is tight
A __________ should be used to prevent the head of a fastener from turning while its nut is being
tightened. - Answer-backup wrench
The opening of an open end wrench is angled __________ degrees to allow it to be flipped over and
repositioned for access to fastenersin tight locations. - Answer-15
Rounded corners on a hex bolt's head __________. - Answer-could cause the wrench to slip off the head
during tightening
An adjustable wrench's movable jaw is positioned by __________. - Answer-rotating a worm gear
Before inserting a threaded fastener into the clearance holes during an assembly operation,
__________. - Answer-visually verify that the fastener will fit through all clearance holes
The ratcheting action of a ratchet wrench allows the user to reset the tool back to its starting point
__________. - Answer-without the need to remove it from the fastener
, A(n) __________ wrench is used to tighten socket head cap screws when there is no hand clearance
around the fastener. - Answer-T-Allen
When tightening a fastener, you should __________. - Answer-pull the wrench towards your body
An adjustable wrench should be positioned on a fastener so that when rotated, __________. - Answer-it
turns towards the movable jaw
When picking a socket to use, a 6-point socket is the __________, although the 12-point is the most
common. - Answer-strongest
What are three of the seven sources of waste that Toyota identified? - Answer-WAITING, DEFECTS,
transportation
Which of the following are rules of lean? Select all that apply - Answer-Activities, connections ,
improvements
Big gains come through large, slow improvements. - Answer-false
Which of the following is not one of the five lean principles? - Answer-Lean is the weapon against waste.
Which of the following are goals of Lean? Select all that apply. - Answer-Improved quality, Faster cycle
time, Improved safety
Drinks are allowed in a clean room as long as it has a lid on it - Answer-False
What area has the cleanest air in a Semiconductor Factory? - Answer-ISO Class 3
The strongest socket with the highest tightening force is the __________ socket - Answer-6 POINT
is/are used to fill the small gaps between threads to prevent leakage of air, gases, or liquids. - Answer-
Sealants
The __________ the fastener the wrench handle is grasped, the greater the tightening force that can be
applied. - Answer-further away from
A T-Allen wrench is used for what purpose? - Answer-When hand clearance around the bolt is tight
A __________ should be used to prevent the head of a fastener from turning while its nut is being
tightened. - Answer-backup wrench
The opening of an open end wrench is angled __________ degrees to allow it to be flipped over and
repositioned for access to fastenersin tight locations. - Answer-15
Rounded corners on a hex bolt's head __________. - Answer-could cause the wrench to slip off the head
during tightening
An adjustable wrench's movable jaw is positioned by __________. - Answer-rotating a worm gear
Before inserting a threaded fastener into the clearance holes during an assembly operation,
__________. - Answer-visually verify that the fastener will fit through all clearance holes
The ratcheting action of a ratchet wrench allows the user to reset the tool back to its starting point
__________. - Answer-without the need to remove it from the fastener
, A(n) __________ wrench is used to tighten socket head cap screws when there is no hand clearance
around the fastener. - Answer-T-Allen
When tightening a fastener, you should __________. - Answer-pull the wrench towards your body
An adjustable wrench should be positioned on a fastener so that when rotated, __________. - Answer-it
turns towards the movable jaw
When picking a socket to use, a 6-point socket is the __________, although the 12-point is the most
common. - Answer-strongest
What are three of the seven sources of waste that Toyota identified? - Answer-WAITING, DEFECTS,
transportation
Which of the following are rules of lean? Select all that apply - Answer-Activities, connections ,
improvements
Big gains come through large, slow improvements. - Answer-false
Which of the following is not one of the five lean principles? - Answer-Lean is the weapon against waste.
Which of the following are goals of Lean? Select all that apply. - Answer-Improved quality, Faster cycle
time, Improved safety
Drinks are allowed in a clean room as long as it has a lid on it - Answer-False
What area has the cleanest air in a Semiconductor Factory? - Answer-ISO Class 3
