• ¿Documento equivocado? Cámbialo gratis
  • Escrito por estudiantes que aprobaron
  • Inmediatamente disponible después del pago
  • Leer en línea o como PDF
Vender
¿Dónde estudias?
Tu idioma
Document preview thumbnail
Vista previa 4 fuera de 37 páginas
Examen

API 510 UPDATED 2026.pdf 1. Document information

Document preview thumbnail
Vista previa 4 fuera de 37 páginas

API 510 UPDATED 1. Document information

Vista previa del contenido

API 510 UPDATED 2026/2027 TEST PAPER QUESTIONS
AND SOLUTIONS RATED A+
✔✔Which of the following is NOT a good reason for substituting a pneumatic test for a
hydrotest?
a) Less expensive
b) Support structure cannot hold the weight of the water
c) Traces of water will put the process product "off-spec"
d) Vessel is refractory lined - ✔✔A

✔✔Which of the following is true when pneumatic testing is performed after a major
repair on a vessel that has a shell that is 0.375" thick?
a) An engineer should develop a specific procedure
b) The test pressure should be 130% of MAWP and corrected for temperature
c) The metal temperature should be anything above MDMT
d) The Owner / User should approve - ✔✔A

✔✔Brittle fractures usually have occurred:
a) During startup
b) During the first hydrotest or overload
c) In vessels made with thinner materials
d) In stainless steel vessels - ✔✔B

✔✔Which of the following materials is most prone to temper embrittlement?
a) Carbon steel
b) High nickel alloys
c) Low chromes
d) Stainless steel - ✔✔C

✔✔A hydrotest is performed on an existing vessel following the replacement of a shell
plate. The vessel is 1-1/2" thick. What is the minimum allowed metal temperature during
the test?
a) 32°F
b) 70°F
c) 10°F above the vessel's MDMT
d) 30°F above the vessel's MDMT - ✔✔C

✔✔A hydrotest is performed on a vessel following the replacement of a 2.5" thick head.
What is the minimum allowed metal temperature during the test?
a) 32°F
b) 70°F
c) 10°F above the vessel's MDMT
d) 30°F above the vessel's MDMT - ✔✔D

,✔✔A hydrotest is performed on a vessel with austenitic SS cladding. What is the
maximum allowed water temperature?
a) 40°F
b) 80°F
c) 120°F
d) 150F - ✔✔C

✔✔NDE is substituted for a pressure test after a major repair on an in-service vessel.
Who must approve this substitution?
a) Just the Inspector
b) Just the Engineer
c) Either the Inspector or Engineer
d) Both the Inspector or Engineer - ✔✔D

✔✔Per API 510, during repairs and alterations, the inspector shall verify that the new
material being used are correct. What is the minimum amount of verification that the
inspector shall perform?
a) 100% of all metallurgy's
b) 100% of all alloys
c) 100% of all high alloys
d) A sampling of all metallurgy's
e) A sampling of all alloys
f) A sampling of all high alloys - ✔✔D

✔✔During repairs and alterations, who determines the percentage of new materials to
check for conformance to specifications?
a) Inspector
b) Owner/User
c) Engineer or Owner/User
d) Inspector or Engineer
e) Inspector or Owner/User - ✔✔E

✔✔Who should perform PMI?
a) Examiner
b) Inspector
c) Examiner or Inspector
d) Examiner or inspector or Qualified Others - ✔✔C

✔✔What document provides addition guidance about material verification?
a) API 571
b) API 578
c) API 580
d) API 2201 - ✔✔B

,✔✔An existing vessel component fails. Analysis of the failure determines that an
incorrect material was inadvertently substituted during fabrication. Who should
determine whether other components should be checked for correct metallurgy?
a) Inspector
b) Owner / User
c) Either the Inspector or Engineer
d) Both the Inspector or Engineer
e) Both the engineer and Owner / User - ✔✔A

✔✔During an in-service inspection, a crack-like flaw was discovered in a weld. This
imperfection must be:
a) Evaluated to the acceptance criteria of the construction code
b) Evaluated to the acceptance criteria of the current ASME VIII
c) Evaluated by an Inspector or Engineer
d) Evaluated by an Engineer or Corrosion Specialist
e) Repaired - ✔✔D

✔✔During an in-service inspection, preferential corrosion was discovered in a weld.
This imperfection shall be evaluated:
a) To the acceptance criteria of the construction code
b) To the acceptance criteria of the current ASME VIII
c) By an Inspector
d) By an Engineer or Corrosion Specialist - ✔✔C

✔✔Flange leaks in certain fluids can cause:
a) Galling of bolts and nuts
b) Bolt lengths to shorten
c) Bolts to crack or corrode
d) Bolting stresses to decrease - ✔✔C

✔✔A leaking flange was repaired by a leak sealing company that pumped sealant in the
gasket area. Later the flange leaks again. What should be done?
a) Examine bolts with UT prior to repumping
b) Examine the flange area with profile RT prior to repumping
c) Repump the flanges
d) Shutdown piping and repair flanges - ✔✔A

✔✔Flange bolts are unacceptable if the lack of engagement exceeds:
a) 0 threads
b) ½ threads
c) 1 thread
d) 2 threads - ✔✔C

✔✔Additional guidance on the inspection and repair of flanged joints can be found in:

, a) ASME PCC-1
b) ASME Section II
c) ASME Section VIII, Div 2
d) API 580 - ✔✔A

✔✔A new vessel is installed. An API 510 inspector shall inspect the vessel at the time
of installation. Which of the following is NOT required during this inspection?
a) Verify the nameplate information matches the data report
b) Verify internal components meet design requirements
c) Verify ladders and platforms are secure
d) Verify whether the pressure-relieving devices are correct
e) Verify no damage to vessel occurred during shipment to the site - ✔✔B

✔✔The Internal Inspection interval must be reviewed whenever changes occur that
could affect the degradation of the vessel. In which of the following situations does a
review of the internal interval NOT need to be conducted?
a) Operating temperature increases
b) Operating pressure decreases
c) Operating pressure increases
d) Fluid composition changes - ✔✔B

✔✔When must both an Internal and External Inspection always be performed?
a) At installation of vessel
b) Whenever there is a change in fluid service
c) Whenever the vessel's ownership changes
d) Whenever the vessel's location changes
e) Whenever the vessel's ownership and location change
f) Whenever the vessel's ownership or location change - ✔✔E

✔✔The Internal Inspection interval obtained from and RBI assessment:
a) Cannot exceed 10 years
b) Cannot exceed the lesser of ½ life or 10 years
c) Can exceed 10 years
d) Can exceed 10 years only if approved by a professional engineer - ✔✔C

✔✔When RBI is used to set an Internal Inspection interval that exceeds the API 10 year
limits, the RBI assessment must be reviewed:
a) Every 5 years
b) Every 10 years
c) At ½ of the RBI inspection interval
d) At the lesser of ½ life or 10 years
e) Behind closed doors - ✔✔B

✔✔An RBI assessment extends the Internal interval beyond the 10 year limit. When
reassessment is done, it must be reviewed and approved by:

Información del documento

Subido en
20 de julio de 2026
Número de páginas
37
Escrito en
2025/2026
Tipo
Examen
Contiene
Preguntas y respuestas
$18.49

¿Documento equivocado? Cámbialo gratis Dentro de los 14 días posteriores a la compra y antes de descargarlo, puedes elegir otro documento. Puedes gastar el importe de nuevo.
Escrito por estudiantes que aprobaron
Inmediatamente disponible después del pago
Leer en línea o como PDF

Seller avatar
Los indicadores de reputación están sujetos a la cantidad de artículos vendidos por una tarifa y las reseñas que ha recibido por esos documentos. Hay tres niveles: Bronce, Plata y Oro. Cuanto mayor reputación, más podrás confiar en la calidad del trabajo del vendedor.
BOARDWALK
3.6
(45)
Vendido
300
Seguidores
11
Artículos
37298
Última venta
2 semanas hace



Por qué los estudiantes eligen Stuvia

Creado por compañeros estudiantes, verificado por reseñas

Calidad en la que puedes confiar: escrito por estudiantes que aprobaron y evaluado por otros que han usado estos resúmenes.

¿No estás satisfecho? Elige otro documento

¡No te preocupes! Puedes elegir directamente otro documento que se ajuste mejor a lo que buscas.

Paga como quieras, empieza a estudiar al instante

Sin suscripción, sin compromisos. Paga como estés acostumbrado con tarjeta de crédito y descarga tu documento PDF inmediatamente.

Student with book image

“Comprado, descargado y aprobado. Así de fácil puede ser.”

Alisha Student

Preguntas frecuentes