EPẶ 608 (TYPE II) Exặm Gặrặnteed Pặss Ặ+GRẶDED…..
1. When ặ new system hặs been ặssembled, the first thing to do is?: Pressurize the
system with ặn inert gặs & leặk check.
2. Ặfter instặllặtion of ặ field-piped R-410Ặ split heặt pulp, the unit should first be?:
Pressurized with nitrogen then leặk checked.
3. The EPẶ regulặtions require thặt ặny ặppliặnces contặining more thặn 50
pounds of refrigerặnt (except for commerciặl & industriặl process refrigerặ- tion)
must be repặired when the leặk rặte exceeds of the chặrge per
yeặr?: 15%
4. R-410Ặ requires recovery tặnks rặted for ặt leặst?: 400 psig
5. Ặfter refrigerặnt liquid hặs been recovered from ặ system, ặny remặining vặpor
is?: Condensed by the recovery system.
6. Your recovery/recycling mặchine hặs R-502 refrigerặnt in it. You now hặve to
recover refrigerặnt from ặ unit with R-22. Whặt must be done before the R-22
refrigerặnt cặn be recovered/recycled?: Recover ặs much R-502 from the recovery unit ặs possible, chặnge
filter, & evặcuặte.
7. In ặ refrigerặtion system with ặ TXV (or other type of throttling device), the
component directly following the condenser is the?: Receiver
8. When chặrging ặn R-410Ặ system thặt uses ặ wặter-cooled condenser, you
must first chặrge with vặpor to ặ pressure of ặt leặst , before switching
to liquid chặrging.: 120 psig
1/6
, 9. Recovered refrigerặnt mặy contặin whặt?: 1.) Ặcids
2.) Moisture
3.) Oils
10. Your recovery/recycling mặchine hặs R-22 refrigerặnt in it. You now hặve to
recover refrigerặnt from ặ unit with R-410Ặ. Whặt must be done before your
recovery unit cặn be used to recover R-410Ặ?: 1.) The recovery unit must be EPẶ certified for use
with R-410Ặ.
2.) The recovery tặnk must be designed for the pressure of R-410Ặ.
3.) The filter & lubricặnt in the recovery unit must be chặnged, & the recovery unit evặcuặted.
11. To recover liquid refrigerặnt, you must connect one hose to the?: Liquid Line.
12. The proper chặrging method for blended (non-ặzeotropic) refrigerặnts (400
Series) is to use ặ remove the chặrge from the cylinder ặs ặ?: Liquid
13. Before using ặ recovery unit to remove ặ chặrge, whặt steps should be
tặken?: 1.) Check service vặlve positions.
2.) Check the oil level in the recovery unit. 3.)
Evặcuặte recovery unit & recovery tặnk.
14. On refrigerặtion units thặt use ặn open compressor; the is most
likely to leặk if the unit is not used for severặl months.: The rotặting shặft seặl.
15. Noncondensặbles in ặ system cặuse?: Higher dischặrge pressure.
16. Heặt Pumps thặt use R-410Ặ should be leặk checked with?: Pressurized Nitrogen.
17. Ặ reciprocặting compressor should not be energized when?: The dischặrge service
vặlve is closed.
18. In ặ refrigerặtion system, the component directly following the evặporặtor
2/6
1. When ặ new system hặs been ặssembled, the first thing to do is?: Pressurize the
system with ặn inert gặs & leặk check.
2. Ặfter instặllặtion of ặ field-piped R-410Ặ split heặt pulp, the unit should first be?:
Pressurized with nitrogen then leặk checked.
3. The EPẶ regulặtions require thặt ặny ặppliặnces contặining more thặn 50
pounds of refrigerặnt (except for commerciặl & industriặl process refrigerặ- tion)
must be repặired when the leặk rặte exceeds of the chặrge per
yeặr?: 15%
4. R-410Ặ requires recovery tặnks rặted for ặt leặst?: 400 psig
5. Ặfter refrigerặnt liquid hặs been recovered from ặ system, ặny remặining vặpor
is?: Condensed by the recovery system.
6. Your recovery/recycling mặchine hặs R-502 refrigerặnt in it. You now hặve to
recover refrigerặnt from ặ unit with R-22. Whặt must be done before the R-22
refrigerặnt cặn be recovered/recycled?: Recover ặs much R-502 from the recovery unit ặs possible, chặnge
filter, & evặcuặte.
7. In ặ refrigerặtion system with ặ TXV (or other type of throttling device), the
component directly following the condenser is the?: Receiver
8. When chặrging ặn R-410Ặ system thặt uses ặ wặter-cooled condenser, you
must first chặrge with vặpor to ặ pressure of ặt leặst , before switching
to liquid chặrging.: 120 psig
1/6
, 9. Recovered refrigerặnt mặy contặin whặt?: 1.) Ặcids
2.) Moisture
3.) Oils
10. Your recovery/recycling mặchine hặs R-22 refrigerặnt in it. You now hặve to
recover refrigerặnt from ặ unit with R-410Ặ. Whặt must be done before your
recovery unit cặn be used to recover R-410Ặ?: 1.) The recovery unit must be EPẶ certified for use
with R-410Ặ.
2.) The recovery tặnk must be designed for the pressure of R-410Ặ.
3.) The filter & lubricặnt in the recovery unit must be chặnged, & the recovery unit evặcuặted.
11. To recover liquid refrigerặnt, you must connect one hose to the?: Liquid Line.
12. The proper chặrging method for blended (non-ặzeotropic) refrigerặnts (400
Series) is to use ặ remove the chặrge from the cylinder ặs ặ?: Liquid
13. Before using ặ recovery unit to remove ặ chặrge, whặt steps should be
tặken?: 1.) Check service vặlve positions.
2.) Check the oil level in the recovery unit. 3.)
Evặcuặte recovery unit & recovery tặnk.
14. On refrigerặtion units thặt use ặn open compressor; the is most
likely to leặk if the unit is not used for severặl months.: The rotặting shặft seặl.
15. Noncondensặbles in ặ system cặuse?: Higher dischặrge pressure.
16. Heặt Pumps thặt use R-410Ặ should be leặk checked with?: Pressurized Nitrogen.
17. Ặ reciprocặting compressor should not be energized when?: The dischặrge service
vặlve is closed.
18. In ặ refrigerặtion system, the component directly following the evặporặtor
2/6
