2A751 EOC Study Guide Exam With
Complete Solutions
If tool length offset is not set during the programming phase, - ANSWER
manually set it at the machine before machining begins.
What is the difference between the staring and trailing sides of a die? - ANSWER
Starting side has three tapered threads; the trailing side has one tapered.
What causes excessive wear on the idler and drive wheels when using the
contour machine? - ANSWER Excessive tension
How do you place a precision level when you install a milling machine? -
ANSWER Longitudinally and laterally on the table.
When you grind out cracks to prepare for a weld repair, you should grind out all
cracks, except those - ANSWER that extend completely through.
What is the revolutions per minute you should use for machine reaming? -
ANSWER One-half the drilling speed.
The most efficient type of grinding wheel dresser for truing wheels used to
perform precision grinding is the - ANSWER diamond dresser
If the line rotates counterclockwise from the initial line, it is a - ANSWER positive
angle
What attaches the knee on the milling machine to the column? - ANSWER
dovetail ways.
To prevent damage to the universal punching and shearing machine, what must
you check to ensure the cutting capacity of the equipment is not exceeded? -
ANSWER Thickness and tensile strength of the material to be cut.
After you install a Heli-Coil, remember to properly remove the tang by - ANSWER
Breaking it off with a breakoff tool
,What do you use if you want to measure a height less than 1 inch with a Vernier
height gage? - ANSWER the offset attachment
Which item on the lathe tool determines chip formation and shear angle? -
ANSWER Face
TO machine a 1"-diameter steel rod with a selected cutting foot speed (CFS) of
80, you determine the lathe spindle revolutions per minute (RPM) with the
formula -- RPM = CFSx4/D, which results in an RPM of - ANSWER 320
Before you tighten or loosen the arbor nut on a horizontal milling machine, you
should - ANSWER Install the arbor support
If you allow the workpiece to stop without relieving the knurling tool pressure,
the - ANSWER work may spring
In oxyacetylene welding, the carburizing flame - ANSWER is the coolest flame
In shielded metal arc welding (SMAW), the difference between an E-7018 and an
E-10018 is - ANSWER the coating thickness
The feature of the quick-change tool post that provides a positive hold and
accurate setting for multiple tool holders is - ANSWER dovetailed surfaces
When performing a roller swaging operation, make sure you center the bearing
and - ANSWER make sure the bearing is square with the hole before you press is
An approximate method of aligning lathe centers is - ANSWER cricket mark
When heat treating nickel alloys, which process most closely resembles the
tempering process in steel? - ANSWER stress relieving
To eliminate the oxide film that results from welding aluminum alloys, use the
gas tungsten arc welding (GTAW) process with - ANSWER AC and Ar shielding
gas
The easiest way to control the weld when you use the GTAW to weld horizontal,
vertical, or overhead is to - ANSWER keep the molten pool small
When removing a broken plug in a cylinder, what should be done to prevent
damage to the cylinder? - ANSWER Pack the plug with grease to keep chips
from falling into the cylinder.
By using the micrometer carriage stop, you can position the carriage to a
tolerance within - ANSWER 0.0010"
, To prepare a chisel for cutting hard materials, grind the cutting edge included
angle to - ANSWER 70 degrees
The mist type coolant delivery system is used - ANSWER for high speed
machining only
To restore ductility to ferritic steel requires - ANSWER annealing
The position of a line at the start of an angle is known as the - ANSWER initial line
What type of end mill is best for interrupted cuts? - ANSWER helical fluted
When you press a plain bearing into a hole it's known as a - ANSWER bushing
When taking a finishing cut during straight turning operations, you should take a
shallow cut of about 1/4" - ANSWER to see if the diameter is correct
When silver soldering on thick metal or a large metal surface, preheat the metal
- ANSWER well away from the joint
To keep a pilot arc when you use alternating current (AC) for GTAW, use the -
ANSWER High-frequency switch
If line segments do not begin and end at the same point when creating geometry
for a computer numerical control, - ANSWER you have problems converting
them to tool paths
To reduce the HAZ, welding speeds are increased by - ANSWER ensuring the
edge preparation provides a good fit-up
When forging a workpiece, you should strike the final blows when the
temperature reaches - ANSWER 1300 degrees F
To obtain the correct diameter of a hole when using an inside micrometer, you
must add to the actual micrometer reading the length of the - ANSWER body and
extension rod.
What is the correct way to operate the telescoping gage when using it to gage a
hole? - ANSWER Set the gage in the hole, open it SLOWLY, and let the plungers
expand fully in the hole for measurement
On a contour machine, which term is used to describe the distance from the saw
band to the column? - ANSWER throat depth
In low carbon steels, to obtain an annealed condition, the steel should be cooled
in - ANSWER still air
Complete Solutions
If tool length offset is not set during the programming phase, - ANSWER
manually set it at the machine before machining begins.
What is the difference between the staring and trailing sides of a die? - ANSWER
Starting side has three tapered threads; the trailing side has one tapered.
What causes excessive wear on the idler and drive wheels when using the
contour machine? - ANSWER Excessive tension
How do you place a precision level when you install a milling machine? -
ANSWER Longitudinally and laterally on the table.
When you grind out cracks to prepare for a weld repair, you should grind out all
cracks, except those - ANSWER that extend completely through.
What is the revolutions per minute you should use for machine reaming? -
ANSWER One-half the drilling speed.
The most efficient type of grinding wheel dresser for truing wheels used to
perform precision grinding is the - ANSWER diamond dresser
If the line rotates counterclockwise from the initial line, it is a - ANSWER positive
angle
What attaches the knee on the milling machine to the column? - ANSWER
dovetail ways.
To prevent damage to the universal punching and shearing machine, what must
you check to ensure the cutting capacity of the equipment is not exceeded? -
ANSWER Thickness and tensile strength of the material to be cut.
After you install a Heli-Coil, remember to properly remove the tang by - ANSWER
Breaking it off with a breakoff tool
,What do you use if you want to measure a height less than 1 inch with a Vernier
height gage? - ANSWER the offset attachment
Which item on the lathe tool determines chip formation and shear angle? -
ANSWER Face
TO machine a 1"-diameter steel rod with a selected cutting foot speed (CFS) of
80, you determine the lathe spindle revolutions per minute (RPM) with the
formula -- RPM = CFSx4/D, which results in an RPM of - ANSWER 320
Before you tighten or loosen the arbor nut on a horizontal milling machine, you
should - ANSWER Install the arbor support
If you allow the workpiece to stop without relieving the knurling tool pressure,
the - ANSWER work may spring
In oxyacetylene welding, the carburizing flame - ANSWER is the coolest flame
In shielded metal arc welding (SMAW), the difference between an E-7018 and an
E-10018 is - ANSWER the coating thickness
The feature of the quick-change tool post that provides a positive hold and
accurate setting for multiple tool holders is - ANSWER dovetailed surfaces
When performing a roller swaging operation, make sure you center the bearing
and - ANSWER make sure the bearing is square with the hole before you press is
An approximate method of aligning lathe centers is - ANSWER cricket mark
When heat treating nickel alloys, which process most closely resembles the
tempering process in steel? - ANSWER stress relieving
To eliminate the oxide film that results from welding aluminum alloys, use the
gas tungsten arc welding (GTAW) process with - ANSWER AC and Ar shielding
gas
The easiest way to control the weld when you use the GTAW to weld horizontal,
vertical, or overhead is to - ANSWER keep the molten pool small
When removing a broken plug in a cylinder, what should be done to prevent
damage to the cylinder? - ANSWER Pack the plug with grease to keep chips
from falling into the cylinder.
By using the micrometer carriage stop, you can position the carriage to a
tolerance within - ANSWER 0.0010"
, To prepare a chisel for cutting hard materials, grind the cutting edge included
angle to - ANSWER 70 degrees
The mist type coolant delivery system is used - ANSWER for high speed
machining only
To restore ductility to ferritic steel requires - ANSWER annealing
The position of a line at the start of an angle is known as the - ANSWER initial line
What type of end mill is best for interrupted cuts? - ANSWER helical fluted
When you press a plain bearing into a hole it's known as a - ANSWER bushing
When taking a finishing cut during straight turning operations, you should take a
shallow cut of about 1/4" - ANSWER to see if the diameter is correct
When silver soldering on thick metal or a large metal surface, preheat the metal
- ANSWER well away from the joint
To keep a pilot arc when you use alternating current (AC) for GTAW, use the -
ANSWER High-frequency switch
If line segments do not begin and end at the same point when creating geometry
for a computer numerical control, - ANSWER you have problems converting
them to tool paths
To reduce the HAZ, welding speeds are increased by - ANSWER ensuring the
edge preparation provides a good fit-up
When forging a workpiece, you should strike the final blows when the
temperature reaches - ANSWER 1300 degrees F
To obtain the correct diameter of a hole when using an inside micrometer, you
must add to the actual micrometer reading the length of the - ANSWER body and
extension rod.
What is the correct way to operate the telescoping gage when using it to gage a
hole? - ANSWER Set the gage in the hole, open it SLOWLY, and let the plungers
expand fully in the hole for measurement
On a contour machine, which term is used to describe the distance from the saw
band to the column? - ANSWER throat depth
In low carbon steels, to obtain an annealed condition, the steel should be cooled
in - ANSWER still air