PIVOT POINT EVALUATION PAPER QUESTIONS AND
ANSWERS SURE A+
✔✔All of the following descriptions are true about the uniformly layered form except: -
✔✔Rectangular or oval shape
✔✔What describes the lengths of the uniformly layered form? - ✔✔Lengths are all equal
✔✔Texturizing reduces bulk without: - ✔✔Shortening the overall appearance of length
✔✔Cutting shorter lengths within the form to reduce bulk and create closeness is called:
- ✔✔Texturizing
✔✔Which area of the head should you avoid thinning the hair? - ✔✔Hairline
✔✔Slightly closed shears move down the strand to produce a rapid length increase in
which of the following techniques? - ✔✔Slide cutting
✔✔What form is also known as a box cut? - ✔✔square
✔✔A very short exterior gradually progressing to a longer interior, similar to graduated
form but shorter, is known as: - ✔✔gradation
✔✔Facial hair design includes beards, goatees, mustaches and - ✔✔Sideburns
✔✔Taper shears, also known as thinning shears, are used on the ends of the hair to: -
✔✔Mobility
✔✔Which of the following descriptions is not a characteristics of the solid form? -
✔✔Interior activation
, ✔✔Solid form sculptures can be created along the following lines except: - ✔✔Vertical
✔✔The distribution used to sculpt solid form is: - ✔✔Natural
✔✔What type of design line is used to sculpt solid form? - ✔✔Stationary
✔✔The weight in a graduated form is positioned: - ✔✔Above the perimeter form line
✔✔The line that visually separates activated and unactivated textures in a graduated
form is called the: - ✔✔Ridge line
✔✔When cutting graduation, higher projection or elevation angles create: - ✔✔High
graduation
✔✔Which of the following projection angles is used to create medium graduation? -
✔✔Above 30, below 60
✔✔The shape of silhouette of the increase layered form resembles which of the
following shapes: - ✔✔Oval
✔✔If weight is desired at the perimeter of an increase layered form, sculpt the perimeter
design line in: - ✔✔Natural fall
✔✔Which parting pattern creates the appearance of weight in a uniformly layered form?
- ✔✔Horizontal
✔✔What type of distribution is used to sculpt uniformly layered form? - ✔✔90 degrees
✔✔What type of design line is used to sculpt uniform lengths? - ✔✔Mobile
✔✔When sculpting uniformly layered lengths, the design line should remain: -
✔✔Visible
✔✔An advanced technique used when sculpting uniform layers on tightly curled hair is
called: - ✔✔Free form
✔✔Which of the following statements is true when sculpting uniformly layered forms
with tighter curl patterns? - ✔✔The hair will appear shorter after sculpting
✔✔Base texturizing is performed up to: - ✔✔1" (2.5 cm) from scalp
ANSWERS SURE A+
✔✔All of the following descriptions are true about the uniformly layered form except: -
✔✔Rectangular or oval shape
✔✔What describes the lengths of the uniformly layered form? - ✔✔Lengths are all equal
✔✔Texturizing reduces bulk without: - ✔✔Shortening the overall appearance of length
✔✔Cutting shorter lengths within the form to reduce bulk and create closeness is called:
- ✔✔Texturizing
✔✔Which area of the head should you avoid thinning the hair? - ✔✔Hairline
✔✔Slightly closed shears move down the strand to produce a rapid length increase in
which of the following techniques? - ✔✔Slide cutting
✔✔What form is also known as a box cut? - ✔✔square
✔✔A very short exterior gradually progressing to a longer interior, similar to graduated
form but shorter, is known as: - ✔✔gradation
✔✔Facial hair design includes beards, goatees, mustaches and - ✔✔Sideburns
✔✔Taper shears, also known as thinning shears, are used on the ends of the hair to: -
✔✔Mobility
✔✔Which of the following descriptions is not a characteristics of the solid form? -
✔✔Interior activation
, ✔✔Solid form sculptures can be created along the following lines except: - ✔✔Vertical
✔✔The distribution used to sculpt solid form is: - ✔✔Natural
✔✔What type of design line is used to sculpt solid form? - ✔✔Stationary
✔✔The weight in a graduated form is positioned: - ✔✔Above the perimeter form line
✔✔The line that visually separates activated and unactivated textures in a graduated
form is called the: - ✔✔Ridge line
✔✔When cutting graduation, higher projection or elevation angles create: - ✔✔High
graduation
✔✔Which of the following projection angles is used to create medium graduation? -
✔✔Above 30, below 60
✔✔The shape of silhouette of the increase layered form resembles which of the
following shapes: - ✔✔Oval
✔✔If weight is desired at the perimeter of an increase layered form, sculpt the perimeter
design line in: - ✔✔Natural fall
✔✔Which parting pattern creates the appearance of weight in a uniformly layered form?
- ✔✔Horizontal
✔✔What type of distribution is used to sculpt uniformly layered form? - ✔✔90 degrees
✔✔What type of design line is used to sculpt uniform lengths? - ✔✔Mobile
✔✔When sculpting uniformly layered lengths, the design line should remain: -
✔✔Visible
✔✔An advanced technique used when sculpting uniform layers on tightly curled hair is
called: - ✔✔Free form
✔✔Which of the following statements is true when sculpting uniformly layered forms
with tighter curl patterns? - ✔✔The hair will appear shorter after sculpting
✔✔Base texturizing is performed up to: - ✔✔1" (2.5 cm) from scalp
