PKSC 2040 TEST 2 STUDY GUIDE
Packaging functions - Answers - • Protect/Preserve
• Dispense
• Contain
• Inform
Containers - Answers - contain, preserve, transport, dispense
Inner Sealers - Answers - preserve, protect
Closers - Answers - preserve, protect, dispense
Printing - Answers - communicate, inform
Uses of rigid and semi rigid? - Answers - FC him
• Food and Beverage
• Industrial
• Chemicals
• Health and beauty
• Medical
Forming methods of rigid/semi rigid? - Answers - •Injection molding
•Injection blow molding
•Stretch blow molding
•Extrusion blow molding (resin pellets for all above)
•Rotational molding (powder)
•Thermoforming (sheets)
PE - Answers - Resins are FDA approved for food contact, but additives must be
individually approves, including mold release agents
Grades: HDPE, LDPE, LLDPE
Nonpolar
HDPE and LDPE are better for rigids, squeeze bottles are low density, milk bottles are
high density
Standard resin for molded containers for industrial products
(plastic films and bottles)
PP - Answers - Many types meet FDA approval for food contact
Good chemical resistance compared to PE
Higher melting point than PE
nonpolar
(hinge mechanism on water bottles)
, PVC - Answers - Issues with FDA approval for food contact (plasticizers)
Degrades at relatively low temp (280 F)
Non food applications: blown, injection, and stretch molded
(Blister packs for gum, tamper resistant packaging)
Environmental
PS - Answers - HIPS used for sheets for thermoforming
Thin wall containers for dairy market
Thermoformed into salad trays
Transparent and glossy
Accepts ink well
PET - Answers - Most meet FDA approval for food contact
Pros: strength, toughness, clarity
Good enough gas barrier for carbonated drinks
Capable of forming light weight bottles
Injection molding uses - Answers - has a little belly button, tapering of the bottle
Used to make containers and closures- need to have details
Process can be used for thermoset and thermoplastics
Ex: CT closures, dairy product cups, small bottles, preforms for PET bottles, large pails
injection molding process - Answers - PIR
1 plasticizing
2 injection
3 ejection/removal
Direct path from molding to finished part
Requires little or no finishing
Fully automated
High reproducibility
High quality
Cooling is the time that slows production- cooling time increases as wall thickness
increases
Injection molded part design - Answers - •Certain resins shrink after cooling (0.1 - 4%)
•Sharp inside corner need to be avoided for easier removal of part from mold
•Molds are expensive so high volume is best (thermoforming may be considered)
injection blow molding - Answers - Two sets of molds are needed:
-Injection molds
-Blow molds
< 16 oz bottles
Toiletries and personal care
Precise finish
Even wall distribution
Packaging functions - Answers - • Protect/Preserve
• Dispense
• Contain
• Inform
Containers - Answers - contain, preserve, transport, dispense
Inner Sealers - Answers - preserve, protect
Closers - Answers - preserve, protect, dispense
Printing - Answers - communicate, inform
Uses of rigid and semi rigid? - Answers - FC him
• Food and Beverage
• Industrial
• Chemicals
• Health and beauty
• Medical
Forming methods of rigid/semi rigid? - Answers - •Injection molding
•Injection blow molding
•Stretch blow molding
•Extrusion blow molding (resin pellets for all above)
•Rotational molding (powder)
•Thermoforming (sheets)
PE - Answers - Resins are FDA approved for food contact, but additives must be
individually approves, including mold release agents
Grades: HDPE, LDPE, LLDPE
Nonpolar
HDPE and LDPE are better for rigids, squeeze bottles are low density, milk bottles are
high density
Standard resin for molded containers for industrial products
(plastic films and bottles)
PP - Answers - Many types meet FDA approval for food contact
Good chemical resistance compared to PE
Higher melting point than PE
nonpolar
(hinge mechanism on water bottles)
, PVC - Answers - Issues with FDA approval for food contact (plasticizers)
Degrades at relatively low temp (280 F)
Non food applications: blown, injection, and stretch molded
(Blister packs for gum, tamper resistant packaging)
Environmental
PS - Answers - HIPS used for sheets for thermoforming
Thin wall containers for dairy market
Thermoformed into salad trays
Transparent and glossy
Accepts ink well
PET - Answers - Most meet FDA approval for food contact
Pros: strength, toughness, clarity
Good enough gas barrier for carbonated drinks
Capable of forming light weight bottles
Injection molding uses - Answers - has a little belly button, tapering of the bottle
Used to make containers and closures- need to have details
Process can be used for thermoset and thermoplastics
Ex: CT closures, dairy product cups, small bottles, preforms for PET bottles, large pails
injection molding process - Answers - PIR
1 plasticizing
2 injection
3 ejection/removal
Direct path from molding to finished part
Requires little or no finishing
Fully automated
High reproducibility
High quality
Cooling is the time that slows production- cooling time increases as wall thickness
increases
Injection molded part design - Answers - •Certain resins shrink after cooling (0.1 - 4%)
•Sharp inside corner need to be avoided for easier removal of part from mold
•Molds are expensive so high volume is best (thermoforming may be considered)
injection blow molding - Answers - Two sets of molds are needed:
-Injection molds
-Blow molds
< 16 oz bottles
Toiletries and personal care
Precise finish
Even wall distribution