TPC 205.1 ELECTRICAL SAFETY AND
PROTECTION FINAL STUDY PAPER 2026
COMPLETE QUESTIONS AND ANSWERS
◉ The employer shall implement and document an overall electrical
safety program that directs activity appropriate to the risk
associated with electrical hazards. Answer: True
◉ The electrical safety program must identify the ? upon which it is
based, the ? by which it is measured and monitored, and the ? to be
utilized before work is started by employees exposed to an electrical
hazard. Answer: C. Principles / controls / procedures
◉ An electrical safety program in compliance with NFPA 70E must
include a risk assessment procedure that addresses the potential for
human error and its negative consequences on people, processes,
the work environment, and equipment. Answer: True
◉ The job safety planning and job briefing requirements mandate
that before starting each job that involves exposure to electrical
hazards the ? must complete a job safety plan and conduct a job
briefing with the employees involved. Answer: B. Employee in
charge
,◉ Test instruments, equipment, and their accessories are required
to be rated for circuits and equipment where they are utilized. UL
61010-1, 1, Safety Requirements for Electrical Equipment for
Measurement, Control, and Laboratory Use - Part 1: General
Requirements, addresses rating and design requirements for voltage
measurement and test instruments intended for use on electrical
systems ? and below. Answer: C. 1000v
◉ Only qualified persons are permitted to perform tasks such as
testing, troubleshooting, and voltage measuring on electrical
equipment ? . Answer: D. where an electrical hazard exists
◉ NFPA 70E Chapter 2 addresses Safety-Related ? Requirements,
and Chapter 3 addresses Safety Requirements for ? Equipment.
Answer: C. Maintenance / Special
◉ NFPA 70E Article 205 addresses General ? Requirements. Answer:
C. Maintenance
◉ NFPA 70E Informative Annex H is titled Requirements for the
Selection of Protective Clothing and Other Personal Protective
Equipment. Answer: False
◉ NFPA 70E Informative Annex M is titled ? Protective Clothing and
Total System Arc Rating. Answer: C. Layering of
,◉ NFPA 70E Article 250 addresses ? and Protective Equipment.
Answer: D. Personal Safety
◉ NFPA 70E Article 245 addresses ? Electric Tools and Equipment.
Answer: D. Portable
◉ Portable electric equipment used in highly conductive work
locations shall be approved for those locations. In job locations
where employees are likely to contact or be drenched with water or
conductive liquids, ? shall also be used. Answer: B. Ground-fault
circuit-interrupter protection for personnel
◉ GFCI protection devices shall be tested ? . Answer: C. In
accordance with the manufacturer's instructions
◉ Electrical conductors and circuit parts shall not be considered to
be in an electrically safe work condition until all of the requirements
of Article ? have been met. Answer: C. 120
◉ One of the conditions where energized electrical conductors and
circuit parts operating at voltages equal to or greater than 50 volts
shall be put into an electrically safe work condition before an
employee performs work where the employee is within the ?
boundary. Answer: B. Limited Approach
, ◉ Energized work is generally prohibited. Such work is permitted
under which of the following conditions? Answer: A. I, II, and III
◉ End of Lesson 1 Answer: Start of Lesson 2
◉ 1. Article 130, Work Involving Electrical Hazards, by definition,
covers work involving four hazards caused by either proximity or
equipment failure. Answer: False
◉ 2. The first section of Article 130 generally states, in part, that all
requirements of Article 130 apply whether a(n) ? analysis is
completed or if Table 130.7(C)(15)(a), Table 130.7(C)(15)(b), and
Table 130.7(C)(15)(c) are used in lieu of an incident energy analysis.
Answer: C. Incident energy
◉ 3. ? is a component of an arc flash risk assessment used to predict
the incident energy of an arc flash for a specified set of conditions.
Answer: C. Incident energy analysis
◉ 4. One of the conditions where energized electrical conductors
and circuit parts operating at voltages equal to or greater than 50
volts shall be put into an electrically safe work condition before an
employee performs work is where the employee is within the ?
boundary. Answer: B. Limited Approach
PROTECTION FINAL STUDY PAPER 2026
COMPLETE QUESTIONS AND ANSWERS
◉ The employer shall implement and document an overall electrical
safety program that directs activity appropriate to the risk
associated with electrical hazards. Answer: True
◉ The electrical safety program must identify the ? upon which it is
based, the ? by which it is measured and monitored, and the ? to be
utilized before work is started by employees exposed to an electrical
hazard. Answer: C. Principles / controls / procedures
◉ An electrical safety program in compliance with NFPA 70E must
include a risk assessment procedure that addresses the potential for
human error and its negative consequences on people, processes,
the work environment, and equipment. Answer: True
◉ The job safety planning and job briefing requirements mandate
that before starting each job that involves exposure to electrical
hazards the ? must complete a job safety plan and conduct a job
briefing with the employees involved. Answer: B. Employee in
charge
,◉ Test instruments, equipment, and their accessories are required
to be rated for circuits and equipment where they are utilized. UL
61010-1, 1, Safety Requirements for Electrical Equipment for
Measurement, Control, and Laboratory Use - Part 1: General
Requirements, addresses rating and design requirements for voltage
measurement and test instruments intended for use on electrical
systems ? and below. Answer: C. 1000v
◉ Only qualified persons are permitted to perform tasks such as
testing, troubleshooting, and voltage measuring on electrical
equipment ? . Answer: D. where an electrical hazard exists
◉ NFPA 70E Chapter 2 addresses Safety-Related ? Requirements,
and Chapter 3 addresses Safety Requirements for ? Equipment.
Answer: C. Maintenance / Special
◉ NFPA 70E Article 205 addresses General ? Requirements. Answer:
C. Maintenance
◉ NFPA 70E Informative Annex H is titled Requirements for the
Selection of Protective Clothing and Other Personal Protective
Equipment. Answer: False
◉ NFPA 70E Informative Annex M is titled ? Protective Clothing and
Total System Arc Rating. Answer: C. Layering of
,◉ NFPA 70E Article 250 addresses ? and Protective Equipment.
Answer: D. Personal Safety
◉ NFPA 70E Article 245 addresses ? Electric Tools and Equipment.
Answer: D. Portable
◉ Portable electric equipment used in highly conductive work
locations shall be approved for those locations. In job locations
where employees are likely to contact or be drenched with water or
conductive liquids, ? shall also be used. Answer: B. Ground-fault
circuit-interrupter protection for personnel
◉ GFCI protection devices shall be tested ? . Answer: C. In
accordance with the manufacturer's instructions
◉ Electrical conductors and circuit parts shall not be considered to
be in an electrically safe work condition until all of the requirements
of Article ? have been met. Answer: C. 120
◉ One of the conditions where energized electrical conductors and
circuit parts operating at voltages equal to or greater than 50 volts
shall be put into an electrically safe work condition before an
employee performs work where the employee is within the ?
boundary. Answer: B. Limited Approach
, ◉ Energized work is generally prohibited. Such work is permitted
under which of the following conditions? Answer: A. I, II, and III
◉ End of Lesson 1 Answer: Start of Lesson 2
◉ 1. Article 130, Work Involving Electrical Hazards, by definition,
covers work involving four hazards caused by either proximity or
equipment failure. Answer: False
◉ 2. The first section of Article 130 generally states, in part, that all
requirements of Article 130 apply whether a(n) ? analysis is
completed or if Table 130.7(C)(15)(a), Table 130.7(C)(15)(b), and
Table 130.7(C)(15)(c) are used in lieu of an incident energy analysis.
Answer: C. Incident energy
◉ 3. ? is a component of an arc flash risk assessment used to predict
the incident energy of an arc flash for a specified set of conditions.
Answer: C. Incident energy analysis
◉ 4. One of the conditions where energized electrical conductors
and circuit parts operating at voltages equal to or greater than 50
volts shall be put into an electrically safe work condition before an
employee performs work is where the employee is within the ?
boundary. Answer: B. Limited Approach
