Elevator Final Exam- Questions with 100%
Correct Answers Verified Updated 2026-
2027
wrench used for rail installation - ✔✔spud wrench
The minimum clearance form the floor to the suspended ceiling is:
a. 80"
b. 96"
c. 7'3"
d. 8'2" - ✔✔a. 80"
what should you be aware of when removing a cab for replacement?
a. The weight that is to be removed from the ceiling.
b. The original weight and counterbalancing.
c. How much the cab was out of square.
,d. Cover the panels so they do not get banged up. - ✔✔b. The original weight and
counterbalancing.
When fans are used on modernization jobs for exhausting fumes, what statement
is correct?
a. They're to keep you cool, not for exhausting fumes.
b. They should direct the fumes into the hoistway.
c. They should direct the fumes into the pit.
d. They should direct the fumes to the outside. - ✔✔d. They should direct the
fumes to the outside.
The star symbol is used on the COP for what?
a. To show where the floor buttons are located.
b. To designate the main floor.
c. To make the door buttons stand out.
d. To show the alarm bell location. - ✔✔b. To designate the main floor.
,Using a laminate stop strip against the fence on a table saw:
a. Keeps the laminate straight to the blade.
b. Keeps the laminate from lifting off the blade.
c. Keeps the laminate from slipping under the fence.
d. Keeps the laminate from going over the fence. - ✔✔c. Keeps the laminate from
slipping under the fence.
The contact adhesives must be before final bonding:
a. 85 degrees
b. Dry
c. Wet to touch
d. Cold - ✔✔b. Dry
What is the most important piece of equipment you have when using a power
saw?
, a. Combination blade
b. Safety glasses
c. Wood rule
d. Framing square - ✔✔b. safety glasses
When using a circular saw, which of the following is correct?
a. Never start the cut until the blade is turning full RPM
b. The base is not adjustable for cutting depth
c. Circular saw blades range from 10 to 16 inches
d. Remove the retractable guard before cutting - ✔✔a. Never start the cut until
the blade is turning full RPM
What is used to make crosscuts on a table saw?
a. Push stick
b. Rip fence
Correct Answers Verified Updated 2026-
2027
wrench used for rail installation - ✔✔spud wrench
The minimum clearance form the floor to the suspended ceiling is:
a. 80"
b. 96"
c. 7'3"
d. 8'2" - ✔✔a. 80"
what should you be aware of when removing a cab for replacement?
a. The weight that is to be removed from the ceiling.
b. The original weight and counterbalancing.
c. How much the cab was out of square.
,d. Cover the panels so they do not get banged up. - ✔✔b. The original weight and
counterbalancing.
When fans are used on modernization jobs for exhausting fumes, what statement
is correct?
a. They're to keep you cool, not for exhausting fumes.
b. They should direct the fumes into the hoistway.
c. They should direct the fumes into the pit.
d. They should direct the fumes to the outside. - ✔✔d. They should direct the
fumes to the outside.
The star symbol is used on the COP for what?
a. To show where the floor buttons are located.
b. To designate the main floor.
c. To make the door buttons stand out.
d. To show the alarm bell location. - ✔✔b. To designate the main floor.
,Using a laminate stop strip against the fence on a table saw:
a. Keeps the laminate straight to the blade.
b. Keeps the laminate from lifting off the blade.
c. Keeps the laminate from slipping under the fence.
d. Keeps the laminate from going over the fence. - ✔✔c. Keeps the laminate from
slipping under the fence.
The contact adhesives must be before final bonding:
a. 85 degrees
b. Dry
c. Wet to touch
d. Cold - ✔✔b. Dry
What is the most important piece of equipment you have when using a power
saw?
, a. Combination blade
b. Safety glasses
c. Wood rule
d. Framing square - ✔✔b. safety glasses
When using a circular saw, which of the following is correct?
a. Never start the cut until the blade is turning full RPM
b. The base is not adjustable for cutting depth
c. Circular saw blades range from 10 to 16 inches
d. Remove the retractable guard before cutting - ✔✔a. Never start the cut until
the blade is turning full RPM
What is used to make crosscuts on a table saw?
a. Push stick
b. Rip fence
