AZ ROC TRADE EXAM B-3 LICENSE EXAM
WITH CORRECT ACTUAL QUESTIONS AND
CORRECTLY WELL DEFINED ANSWERS
LATEST ALREADY GRADED A+
What should be added to Portland cement to create
mortar? - ANSWERS-Sand, lime and water.
What is added to mortar to increase is bonding abilities? -
ANSWERS-Add hydrated lime
Three types of masonry ties are__________ - ANSWERS-
Rectangular, Corrugated, and Z.
on a double wythe masonry wall with a 2 inch cavity, what
is the required spacing of reinforcing metal ties? -
ANSWERS-4 1/2 square feet
ties for veneer shall be spaced no greater than - ANSWERS-
24 inches on center.
,Panel wall framing track shall have a minimum flange width
of ________? - ANSWERS-1-1/4 inch
What is the minimum size screw for the attaching gypsum
board to metal studs? - ANSWERS-#6
Engineered structural wood product finished on 4 sides is
known as? - ANSWERS-Premium Glulam Beam
Rectangular shap having 2 sides cut into the edge of a board
is known as___________? - ANSWERS-Rabbet
What is the spacing required if using 1-1/4 inch screws to
hang drywall on studs that are 24 inches on center? -
ANSWERS-12 inches.
If you peel of siding and the wood is dark brown and
crumbly, what is the probable cause? - ANSWERS-Dry rot
Refer to the illustration of a story house W/ lap siding plans,
(complete set of plans at the test center), what is the height
from the first floor to the landing? - ANSWERS-61 1/2 inches
,Concerning exterior sheathing, how far above grade should
it extend? - ANSWERS-6 inches
Which of the following wood is most resistant to termites? -
ANSWERS-Redwood
How would you remove a nail from a piece of panel board? -
ANSWERS-Pull it through the back with nippers.
Refer to the illustration of a 2 story house w/ lap siding
plans, (complete set of plans at the test center), How many
pieces of 8 foot chair rail, installed at 36 inch height, are
needed for the dining room? - ANSWERS-5
Which of the following grades of veneer plywood designates
the highest quality? - ANSWERS-A
What is the actual size of a 2x4 surfaced dry piece of
framing lumber? - ANSWERS-1-1/2 by 3-1/2
What is the minimum height of a guardrail on a residential
deck? - ANSWERS-36 inches
, An untreated wood girder beam that sets in a pocket of a
concrete foundation wall that is subject to weather shall
have a minimum air space of ? - ANSWERS-1/2 inch
When framing a 5 foot by 5 foot opening in a wood joist
floor for a stairwell you should: - ANSWERS-double header
and trimmer joists
Notches on the ends of joists shall not exceed _______
percent of the joist depth. - ANSWERS-25(1/4th)
According to code the MAXIMUM diameter of a hole that
may be bored in a 2 by 10 joist is __________ inches. -
ANSWERS-3
According to the code, notches allowed in the top or bottom
of joists shall not exceed what fraction of the depth of the
joist? - ANSWERS-1/6
How much can be notched from a non-load bearing stud
without compromising its structural integrity? - ANSWERS-
40%
WITH CORRECT ACTUAL QUESTIONS AND
CORRECTLY WELL DEFINED ANSWERS
LATEST ALREADY GRADED A+
What should be added to Portland cement to create
mortar? - ANSWERS-Sand, lime and water.
What is added to mortar to increase is bonding abilities? -
ANSWERS-Add hydrated lime
Three types of masonry ties are__________ - ANSWERS-
Rectangular, Corrugated, and Z.
on a double wythe masonry wall with a 2 inch cavity, what
is the required spacing of reinforcing metal ties? -
ANSWERS-4 1/2 square feet
ties for veneer shall be spaced no greater than - ANSWERS-
24 inches on center.
,Panel wall framing track shall have a minimum flange width
of ________? - ANSWERS-1-1/4 inch
What is the minimum size screw for the attaching gypsum
board to metal studs? - ANSWERS-#6
Engineered structural wood product finished on 4 sides is
known as? - ANSWERS-Premium Glulam Beam
Rectangular shap having 2 sides cut into the edge of a board
is known as___________? - ANSWERS-Rabbet
What is the spacing required if using 1-1/4 inch screws to
hang drywall on studs that are 24 inches on center? -
ANSWERS-12 inches.
If you peel of siding and the wood is dark brown and
crumbly, what is the probable cause? - ANSWERS-Dry rot
Refer to the illustration of a story house W/ lap siding plans,
(complete set of plans at the test center), what is the height
from the first floor to the landing? - ANSWERS-61 1/2 inches
,Concerning exterior sheathing, how far above grade should
it extend? - ANSWERS-6 inches
Which of the following wood is most resistant to termites? -
ANSWERS-Redwood
How would you remove a nail from a piece of panel board? -
ANSWERS-Pull it through the back with nippers.
Refer to the illustration of a 2 story house w/ lap siding
plans, (complete set of plans at the test center), How many
pieces of 8 foot chair rail, installed at 36 inch height, are
needed for the dining room? - ANSWERS-5
Which of the following grades of veneer plywood designates
the highest quality? - ANSWERS-A
What is the actual size of a 2x4 surfaced dry piece of
framing lumber? - ANSWERS-1-1/2 by 3-1/2
What is the minimum height of a guardrail on a residential
deck? - ANSWERS-36 inches
, An untreated wood girder beam that sets in a pocket of a
concrete foundation wall that is subject to weather shall
have a minimum air space of ? - ANSWERS-1/2 inch
When framing a 5 foot by 5 foot opening in a wood joist
floor for a stairwell you should: - ANSWERS-double header
and trimmer joists
Notches on the ends of joists shall not exceed _______
percent of the joist depth. - ANSWERS-25(1/4th)
According to code the MAXIMUM diameter of a hole that
may be bored in a 2 by 10 joist is __________ inches. -
ANSWERS-3
According to the code, notches allowed in the top or bottom
of joists shall not exceed what fraction of the depth of the
joist? - ANSWERS-1/6
How much can be notched from a non-load bearing stud
without compromising its structural integrity? - ANSWERS-
40%
