ASE BRAKES A5 TEST (EXAM 1) QUESTIONS WITH CORRECT ANSWERS

ASE BRAKES A5 TEST (EXAM 1) QUESTIONS
WITH CORRECT ANSWERS 2026-2027

A drum is chattering on the brake lathe. This could be a result of



a. failure to install the dampening belt

b. cutting too slowly

c. dull cutting blades

d. cutting speed too fast - CORRECT ANSWER -A : failure to install the dampening belt



why : a missing dampening belt could cause the drum to vibrate while on the lathe. this vibration
can cause the drum to bounce on the cutting tip and make a chattering noise



A vehicle equipped with a hydro-
boost brake system has a hard pedal with little braking action. Which of the following could be the
cause?



a. low brake fluid

b. air in the brake fluid

c. low power steering fluid

d. an overtightened power steering belt - CORRECT ANSWER -C : low power steering fluid



why : low power steering fluid can cause the booster to provide very little if any boost



Which of the following could cause excessive noise braking?



a. worn wheel cylinders

b. worn caliper pistons

c. seized caliper slides

d. missing clips - CORRECT ANSWER -D : missing clips

,why : missing anti-rattle clips could cause excessive noise while braking



A vehicle equipped with a "hill holding" option has an ABS code. Which tool would most likely be
used to check the wheel speed sensor?



a. AC volt meter

b. Ohm meter

c. Scan tool

d. Ammeter - CORRECT ANSWER -C : scan tool



why : a scan tool or oscilloscope can be used to test a signal from a digital when speed sensor



The brake system has a soft, sinking pedal with the engine running. The brake fluid level is at the
correct height. Which of the following could be the cause?



a. a restricted vacuum hose

b. a leaking master cylinder

c. a bypassing master cylinder

d. a stuck open vacuum check valve - CORRECT ANSWER -C : a bypassing master cylinder



why : a bypassing master cylinder would cause a low pedal and would not cause a loss of fluid



Technician A says the pins should be driven in with a brass hammer. Technician B says the pins sh
ould be lubricated with brake fluid. Who is correct? ( pg. 47 )



a. A

b. B

c. A & B

d. neither A OR B - CORRECT ANSWER -D : neither A OR B

, why : neither technician is correct. this style of pin should be installed with a torx or hex head
X 2 X 2 X 2 X 2 X 2 X 2 X 2 X 2 X 2 X 2 X 2 X 2 X 2 X 2 X 2 X 2 X 2 X 2




soc ket
X 2 X2




Technician A says a hydro- X 2 X 2 X 2 X 2




boost system can use the power steering pump to operate the booster. Technician B says a hydr
X 2 X 2 X 2 X 2 X 2 X 2 X 2 X 2 X 2 X 2 X 2 X 2 X 2 X 2 X 2 X 2




o- boost system can use engine vacuum to operate the booster. Who is correct? ( pg. 47 )
X2 X 2 X 2 X 2 X 2 X 2 X 2 X 2 X 2 X 2 X 2 X 2 X 2 X 2 X 2 X 2 X 2




a. A

b. B

c. A & B X 2 X 2




d. neither A & B - CORRECT ANSWER -A : only A
X 2 X 2 X 2 X 2 X 2 X 2 X 2 X 2 X 2 X 2




why : only tech A is correct. a hydro-boost system uses hydraulic pressure to create boost
X 2 X 2 X 2 X 2 X 2 X 2 X 2 X 2 X 2 X 2 X 2 X 2 X 2 X 2 X 2




A disc brake caliper is dragging. All of the following could be the cause EXCEPT
X 2 X 2 X 2 X 2 X 2 X 2 X 2 X 2 X 2 X 2 X 2 X 2 X 2 X 2




a. binding pins X 2




b. sticking piston X 2




c. binding caliper X 2




d. worn brake pads - CORRECT ANSWER -D : worn brake pads
X 2 X 2 X 2 X 2 X 2 X 2 X 2 X 2 X 2 X 2




why : worn brake pads will not cause the brakes to drag
X 2 X 2 X 2 X 2 X 2 X 2 X 2 X 2 X 2 X 2 X 2




Which operation is being performed in the illustration? ( pg. 48 )
X 2 X 2 X 2 X 2 X 2 X 2 X 2 X 2 X 2 X 2 X 2




a. wheel cylinder bleeding X 2 X 2




b. brake caliper bleeding X 2 X 2




c. master cylinder bleeding X 2 X 2




d. master cylinder pressure test - CORRECT ANSWER -C : master cylinder bleeding
X 2 X 2 X 2 X 2 X 2 X 2 X 2 X 2 X 2 X 2 X 2