AUTO BODY FINAL REVIEW
QUESTIONS & ANSWERS
Grinding and cutting requires which of the following equipment? - ANSWERface mask,
leather gloves, dust mask
the object a vehilce collides with is called the - ANSWERtarget
Factors which impact the amount of damage that occurs when a vehicle is in a collision
are all except: - ANSWERdriver age
which type of crown is the most rigid? - ANSWERdouble crown
which type of ball hit the ground with the most force when dropped from a height of one
foot? - ANSWERbowling ball
in which type of panel is n arrowhead most likely to form? - ANSWERhigh crown
force acting on an object must overcome this to make the object move -
ANSWERinertia
if two vehicles collide, the damage will be _________ if the front of one vehicle hits the
center of the other vehicle rather than the end. - ANSWERgreater
lateral movement of the side frame rails after a collision is called a - ANSWERsideway
what rule states that the damaged high-strength steel parts can be repaired if they are
bent but must be replaced if the are kinked - ANSWERthe bend-versus-kink rule
what type of steel has a large loose grain pattern - ANSWERmild
what type of steel has a small tight grain pattern - ANSWERhigh-strength
metal made with _______ will return to its original position if the force holding the metal
out of position is removed. - ANSWERelastic deformation
the ability of metal to be shaped is known as - ANSWERplasticity
the curvature of a panel is called a - ANSWERcrown
The two ways force can impact on a panel are longitudinally and _____________ -
ANSWERlaterally
, A _________________ has a buckle that is greater than 90 degrees in a short area -
ANSWERkink
Damage that occurs at the point of contact during a collision is called - ANSWERdirect
damage
force from the side is called - ANSWERlateral force
product of the weight and speed of an object - ANSWERforce
particle in metal - ANSWERgrain
collision object - ANSWERtarget
minimum force for permanent change in metal grain arrangement - ANSWERyield point
tendency of an object in motion to stay in motion - ANSWERinertia
ability to bend and bounce back - ANSWERelasticity
force from an end - ANSWERlongitudinal
change in frame length - ANSWERmash
decrease in surface area by compression of grains - ANSWERupset
lateral movement of the frame rails - ANSWERsideway
technician must replace area or panel if this is present - ANSWERkink
present when frame rails or rocker panels are on level with each other - ANSWERtwist
frame push up - ANSWERkick up
frame pushed down - ANSWERsag
high crown picture - ANSWER
double crown picture - ANSWER
low crown picture - ANSWER
reverse crown - ANSWER
which size is a drive of sockets? 1/4" 3/8" 1/2? All of the above? - ANSWER1/2 inches
QUESTIONS & ANSWERS
Grinding and cutting requires which of the following equipment? - ANSWERface mask,
leather gloves, dust mask
the object a vehilce collides with is called the - ANSWERtarget
Factors which impact the amount of damage that occurs when a vehicle is in a collision
are all except: - ANSWERdriver age
which type of crown is the most rigid? - ANSWERdouble crown
which type of ball hit the ground with the most force when dropped from a height of one
foot? - ANSWERbowling ball
in which type of panel is n arrowhead most likely to form? - ANSWERhigh crown
force acting on an object must overcome this to make the object move -
ANSWERinertia
if two vehicles collide, the damage will be _________ if the front of one vehicle hits the
center of the other vehicle rather than the end. - ANSWERgreater
lateral movement of the side frame rails after a collision is called a - ANSWERsideway
what rule states that the damaged high-strength steel parts can be repaired if they are
bent but must be replaced if the are kinked - ANSWERthe bend-versus-kink rule
what type of steel has a large loose grain pattern - ANSWERmild
what type of steel has a small tight grain pattern - ANSWERhigh-strength
metal made with _______ will return to its original position if the force holding the metal
out of position is removed. - ANSWERelastic deformation
the ability of metal to be shaped is known as - ANSWERplasticity
the curvature of a panel is called a - ANSWERcrown
The two ways force can impact on a panel are longitudinally and _____________ -
ANSWERlaterally
, A _________________ has a buckle that is greater than 90 degrees in a short area -
ANSWERkink
Damage that occurs at the point of contact during a collision is called - ANSWERdirect
damage
force from the side is called - ANSWERlateral force
product of the weight and speed of an object - ANSWERforce
particle in metal - ANSWERgrain
collision object - ANSWERtarget
minimum force for permanent change in metal grain arrangement - ANSWERyield point
tendency of an object in motion to stay in motion - ANSWERinertia
ability to bend and bounce back - ANSWERelasticity
force from an end - ANSWERlongitudinal
change in frame length - ANSWERmash
decrease in surface area by compression of grains - ANSWERupset
lateral movement of the frame rails - ANSWERsideway
technician must replace area or panel if this is present - ANSWERkink
present when frame rails or rocker panels are on level with each other - ANSWERtwist
frame push up - ANSWERkick up
frame pushed down - ANSWERsag
high crown picture - ANSWER
double crown picture - ANSWER
low crown picture - ANSWER
reverse crown - ANSWER
which size is a drive of sockets? 1/4" 3/8" 1/2? All of the above? - ANSWER1/2 inches
