NEIEP 200 Final Review 2026 | Actual
Questions and Answers | 100% Correct | A
Grade
This NEIEP 200 Final Exam is an exhaustive 73-question test assessing your understanding
of elevator mechanics, rigging safety, load calculations, and code compliance. Master this
exam by reviewing industry-standard topics and utilize this dedicated study guide.
Key subject areas and representative concepts typically tested on this exam include:
1. Rigging & Load Calculations
Lift Plan: Must be created and overseen by the lift director.
Safety Factors: ASME requires a 5:1 safety factor for wire rope slings.
Core Damage: Solvents can cause unapparent wear and tear to fiber core wire rope
slings.
2. Mechanics & Elevator Systems
Counterweight Sizing: For a standard \(40\%\) installation, the counterweight assembly
should equal the car weight plus \(40\%\) of the rated capacity.
Safety Tripping: Counterweight safeties are set to trip up to \(10\%\) higher than the car
governor speed.
Type C Safeties: These safeties utilize an oil buffer between the car and safety planks.
3. Safety Mechanisms & Buffers
Terminal Motion Switch: Its purpose is to automatically slow down and stop the
elevator car at or near terminal landings.
Oil Buffers: These components should not be disassembled in the field.
Loss of Traction: When the counterweight lands on its buffer, it creates a loss of traction
to prevent the elevator car from being pulled into the overhead.
To access this complete, verified 73-question and answer bank for your test prep, check out
this verified apprentice study, which is a comprehensive exam review uploaded by fellow
passed NEIEP students
1
, Quiz_________________?
_______should not be disassembled in the field. -
Answer
Oil Buffers
Quiz_________________?
A reference mark from which vertical measurements are made is known as a -
Answer
Bench Mark
Quiz_________________?
All cab modernization should be performed at what floor? -
Answer
Top floor
Quiz_________________?
At what speed should the counterweight safeties be set to trip? -
Answer
Up to 10% higher than the car governor
Quiz_________________?
2
, For carpet installation, if the cab area measures 94 inches by 62 inches and you
need an additional six inches on each side to account for waste during cutting,
how many square yards of carpet do you need for this job? -
Answer
6
Quiz_________________?
How are the ends of rails made so they may be joined together? -
Answer
The ends have a tongue and groove
Quiz_________________?
How high would you block up a counterweight frame before roping that had a
counterweight buffer height of 32", rope strectch of 12"; bottom counterweight
runby of 18"; and pit depth of 8 feet? -
Answer
62"
Quiz_________________?
How many seizings are required on each side of the cut for preformed rope
according to ASME? -
Answer
1
3
Questions and Answers | 100% Correct | A
Grade
This NEIEP 200 Final Exam is an exhaustive 73-question test assessing your understanding
of elevator mechanics, rigging safety, load calculations, and code compliance. Master this
exam by reviewing industry-standard topics and utilize this dedicated study guide.
Key subject areas and representative concepts typically tested on this exam include:
1. Rigging & Load Calculations
Lift Plan: Must be created and overseen by the lift director.
Safety Factors: ASME requires a 5:1 safety factor for wire rope slings.
Core Damage: Solvents can cause unapparent wear and tear to fiber core wire rope
slings.
2. Mechanics & Elevator Systems
Counterweight Sizing: For a standard \(40\%\) installation, the counterweight assembly
should equal the car weight plus \(40\%\) of the rated capacity.
Safety Tripping: Counterweight safeties are set to trip up to \(10\%\) higher than the car
governor speed.
Type C Safeties: These safeties utilize an oil buffer between the car and safety planks.
3. Safety Mechanisms & Buffers
Terminal Motion Switch: Its purpose is to automatically slow down and stop the
elevator car at or near terminal landings.
Oil Buffers: These components should not be disassembled in the field.
Loss of Traction: When the counterweight lands on its buffer, it creates a loss of traction
to prevent the elevator car from being pulled into the overhead.
To access this complete, verified 73-question and answer bank for your test prep, check out
this verified apprentice study, which is a comprehensive exam review uploaded by fellow
passed NEIEP students
1
, Quiz_________________?
_______should not be disassembled in the field. -
Answer
Oil Buffers
Quiz_________________?
A reference mark from which vertical measurements are made is known as a -
Answer
Bench Mark
Quiz_________________?
All cab modernization should be performed at what floor? -
Answer
Top floor
Quiz_________________?
At what speed should the counterweight safeties be set to trip? -
Answer
Up to 10% higher than the car governor
Quiz_________________?
2
, For carpet installation, if the cab area measures 94 inches by 62 inches and you
need an additional six inches on each side to account for waste during cutting,
how many square yards of carpet do you need for this job? -
Answer
6
Quiz_________________?
How are the ends of rails made so they may be joined together? -
Answer
The ends have a tongue and groove
Quiz_________________?
How high would you block up a counterweight frame before roping that had a
counterweight buffer height of 32", rope strectch of 12"; bottom counterweight
runby of 18"; and pit depth of 8 feet? -
Answer
62"
Quiz_________________?
How many seizings are required on each side of the cut for preformed rope
according to ASME? -
Answer
1
3
