Florida Certified General Contractor
Exam Practice Questions And Correct
Answers (Verified Answers) Plus
Rationale 2026 Q&A| Instant Download
Pdf
1. A Florida Certified General Contractor is reviewing a set of
construction documents for a multi-story commercial structure
located in a coastal wind-borne debris region. Before submitting the
permit application, the contractor notices that the structural drawings
specify impact-resistant glazing while the architectural drawings
specify standard tempered glass. According to sound construction
management practice and Florida code compliance procedures, what
should the contractor do FIRST before proceeding with procurement
or permit submission?
,A. Order the tempered glass because architectural drawings govern finish
materials
B. Ignore the discrepancy because the engineer’s specifications override all
other documents
C. Submit a Request for Information (RFI) to clarify the discrepancy before
construction proceeds
D. Install the glazing system with the lowest cost to maintain project budget
C. Submit a Request for Information (RFI) to clarify the discrepancy before
construction proceeds
A contractor must resolve conflicting construction documents before
permit approval or material procurement to avoid code violations, liability
exposure, and costly rework. Formal clarification through an RFI ensures
the design professional provides an authoritative interpretation consistent
with Florida building requirements for wind protection.
2. During the excavation phase of a Florida commercial building project,
groundwater begins entering the footing trenches after heavy
rainstorms. The project schedule is threatened because reinforcement
installation cannot proceed until the trenches remain stable and dry.
Which corrective action is the MOST appropriate for the contractor to
implement immediately?
,A. Continue placing reinforcement despite standing water conditions
B. Install temporary dewatering systems and stabilize trench conditions
before concrete placement
C. Reduce the footing depth to avoid groundwater intrusion
D. Delay the project indefinitely until the rainy season ends
B. Install temporary dewatering systems and stabilize trench conditions
before concrete placement
Footings must be placed on stable, properly prepared bearing surfaces free
from excessive water accumulation. Dewatering systems such as pumps
and drainage trenches help maintain excavation integrity and ensure
concrete quality, preventing settlement and structural deficiencies.
3. A contractor is preparing a cost estimate for a negotiated lump-sum
contract involving extensive interior renovations to an occupied
healthcare facility. Which project factor creates the GREATEST
estimating risk for the contractor?
A. The color selection for wall finishes
B. Unknown concealed existing conditions behind walls and ceilings
C. The type of temporary fencing used on the project
D. The landscaping design around the parking area
B. Unknown concealed existing conditions behind walls and ceilings
, Renovation projects often contain hidden structural, electrical, plumbing,
or hazardous material conditions that cannot be fully verified before
demolition. These concealed conditions can dramatically increase labor,
schedule, and material costs, making them one of the largest risks in
renovation estimating.
4. A Florida Certified General Contractor is responsible for ensuring
OSHA compliance on a large construction project involving multiple
subcontractors. Which party bears the PRIMARY responsibility for
correcting a known fall protection hazard on the jobsite?
A. Only the subcontractor whose employee created the hazard
B. Only the property owner financing the project
C. The controlling contractor responsible for site safety coordination
D. The local building inspector conducting periodic inspections
C. The controlling contractor responsible for site safety coordination
Under OSHA’s multi-employer worksite doctrine, the controlling contractor
has authority over the project and is responsible for ensuring safety
compliance across the site. The contractor must identify, correct, or require
correction of known hazards affecting workers.
5. A contractor is constructing a reinforced concrete slab-on-grade for a
warehouse facility in Florida. Shortly after placement, surface cracking
Exam Practice Questions And Correct
Answers (Verified Answers) Plus
Rationale 2026 Q&A| Instant Download
1. A Florida Certified General Contractor is reviewing a set of
construction documents for a multi-story commercial structure
located in a coastal wind-borne debris region. Before submitting the
permit application, the contractor notices that the structural drawings
specify impact-resistant glazing while the architectural drawings
specify standard tempered glass. According to sound construction
management practice and Florida code compliance procedures, what
should the contractor do FIRST before proceeding with procurement
or permit submission?
,A. Order the tempered glass because architectural drawings govern finish
materials
B. Ignore the discrepancy because the engineer’s specifications override all
other documents
C. Submit a Request for Information (RFI) to clarify the discrepancy before
construction proceeds
D. Install the glazing system with the lowest cost to maintain project budget
C. Submit a Request for Information (RFI) to clarify the discrepancy before
construction proceeds
A contractor must resolve conflicting construction documents before
permit approval or material procurement to avoid code violations, liability
exposure, and costly rework. Formal clarification through an RFI ensures
the design professional provides an authoritative interpretation consistent
with Florida building requirements for wind protection.
2. During the excavation phase of a Florida commercial building project,
groundwater begins entering the footing trenches after heavy
rainstorms. The project schedule is threatened because reinforcement
installation cannot proceed until the trenches remain stable and dry.
Which corrective action is the MOST appropriate for the contractor to
implement immediately?
,A. Continue placing reinforcement despite standing water conditions
B. Install temporary dewatering systems and stabilize trench conditions
before concrete placement
C. Reduce the footing depth to avoid groundwater intrusion
D. Delay the project indefinitely until the rainy season ends
B. Install temporary dewatering systems and stabilize trench conditions
before concrete placement
Footings must be placed on stable, properly prepared bearing surfaces free
from excessive water accumulation. Dewatering systems such as pumps
and drainage trenches help maintain excavation integrity and ensure
concrete quality, preventing settlement and structural deficiencies.
3. A contractor is preparing a cost estimate for a negotiated lump-sum
contract involving extensive interior renovations to an occupied
healthcare facility. Which project factor creates the GREATEST
estimating risk for the contractor?
A. The color selection for wall finishes
B. Unknown concealed existing conditions behind walls and ceilings
C. The type of temporary fencing used on the project
D. The landscaping design around the parking area
B. Unknown concealed existing conditions behind walls and ceilings
, Renovation projects often contain hidden structural, electrical, plumbing,
or hazardous material conditions that cannot be fully verified before
demolition. These concealed conditions can dramatically increase labor,
schedule, and material costs, making them one of the largest risks in
renovation estimating.
4. A Florida Certified General Contractor is responsible for ensuring
OSHA compliance on a large construction project involving multiple
subcontractors. Which party bears the PRIMARY responsibility for
correcting a known fall protection hazard on the jobsite?
A. Only the subcontractor whose employee created the hazard
B. Only the property owner financing the project
C. The controlling contractor responsible for site safety coordination
D. The local building inspector conducting periodic inspections
C. The controlling contractor responsible for site safety coordination
Under OSHA’s multi-employer worksite doctrine, the controlling contractor
has authority over the project and is responsible for ensuring safety
compliance across the site. The contractor must identify, correct, or require
correction of known hazards affecting workers.
5. A contractor is constructing a reinforced concrete slab-on-grade for a
warehouse facility in Florida. Shortly after placement, surface cracking
