NACE CIP 1 CBT PRACTICE EXAM | QUESTIONS AND ANSWERS |
VERIFIED ANSWERS GRADED A+ | LATEST EXAM UPDATE
Dew point is the temperature at which - CORRECT ANSWERS -
condensation occurs.
You are the NACE Inspector on a tank lining project where a 50% solids epoxy
tank lining is being applied. After application of the 19 coat you notice small
blisters in some areas of the applied lining. Your FIRST preferred course of
action is to: - CORRECT ANSWERS - Document the problem and advise the
Contractor and Owner's representative.
If a contractor is using a poorly maintained compressor to supply air for
abrasive blast cleaning and conventional airspray, the coating inspector should
perform a - CORRECT ANSWERS - blotter test for the presence of oil and
water.
Upon arrival of coating materials, the inspector should - CORRECT
ANSWERS - observe and document the amount of material and batch numbers.
Relative humidity is - CORRECT ANSWERS - a measure of the amount of
moisture in the air compared to saturation level.
Galvanic corrosion occurs on which of the following substrates? - CORRECT
ANSWERS - Metal
When applying Thermal Spray Coatings the specification is most likely to
reference: - CORRECT ANSWERS - SSPC-CS 23.00/AWS C2.23/NACE No.
12
,What is the minimum recommended distance away from an edge that an
inspector should take a measurement with a dial type magnetic pull off Dry
Film Thickness(DFT) gauge? - CORRECT ANSWERS - 2.5 cm (1 inch)
Polymerization is the process of? - CORRECT ANSWERS - Monomers
joining together.
An exposed area of the substrate or previous coat of a conductive material, often
caused by poor application technique is called: - CORRECT ANSWERS -
Holiday
Checking is: - CORRECT ANSWERS - a fine crack in the surface of a coating
that rarely reaches the substrate.
Inspection documentation is important because: - CORRECT ANSWERS -
Owners use the documentation for a variety of purposes.
An Inspectors personal log book should contain: - CORRECT ANSWERS -
No comments regarding the application team.
You have just received your NACE CIP Level 1 certification when you are
asked to supervise a team of uncertified field pipeline inspectors. Your FIRST
preferred course of action is to: - CORRECT ANSWERS - Review the NACE
Attestation prior to making a decision.
Good record can provide maintenance departments with detailed information
about ALL of the following EXCEPT: - CORRECT ANSWERS - How the
item was coated.
, Non Conformance Reports are completed by the Inspector: - CORRECT
ANSWERS - When the Inspector and Contractor deem it to be significant non
conforming item.
The initial steel condition is important to the NACE Inspector because: -
CORRECT ANSWERS - The Inspector may have to reject the steel.
The form of corrosion that has the largest potential for unexpected catastrophic
failure is: - CORRECT ANSWERS - Galvanic Corrosion
What is used to determine compressed air cleanliness? - CORRECT
ANSWERS - Profilometer
Osmotic blistering is most likely to occur as a result of: - CORRECT
ANSWERS - Airless spray application.
When performing tests for oil and grease using an ultra violet light, the NACE
Inspector should be aware that: - CORRECT ANSWERS - Synthetic oil or
grease may not be identified.
To achieve consistently accurate results with ALL alt test equipment: -
CORRECT ANSWERS - wash your hands before sampling.
When holiday testing is required the Inspector is always required to enforce
what standard? - CORRECT ANSWERS - NACE SP 0188
If the specifier does not identify a restriction level in accordance with SSPC PA
2, the default restriction level is: - CORRECT ANSWERS - Level 3
Fine cracks in the surface of a coating that rarely reach the substrate are called: -
CORRECT ANSWERS - Checking
VERIFIED ANSWERS GRADED A+ | LATEST EXAM UPDATE
Dew point is the temperature at which - CORRECT ANSWERS -
condensation occurs.
You are the NACE Inspector on a tank lining project where a 50% solids epoxy
tank lining is being applied. After application of the 19 coat you notice small
blisters in some areas of the applied lining. Your FIRST preferred course of
action is to: - CORRECT ANSWERS - Document the problem and advise the
Contractor and Owner's representative.
If a contractor is using a poorly maintained compressor to supply air for
abrasive blast cleaning and conventional airspray, the coating inspector should
perform a - CORRECT ANSWERS - blotter test for the presence of oil and
water.
Upon arrival of coating materials, the inspector should - CORRECT
ANSWERS - observe and document the amount of material and batch numbers.
Relative humidity is - CORRECT ANSWERS - a measure of the amount of
moisture in the air compared to saturation level.
Galvanic corrosion occurs on which of the following substrates? - CORRECT
ANSWERS - Metal
When applying Thermal Spray Coatings the specification is most likely to
reference: - CORRECT ANSWERS - SSPC-CS 23.00/AWS C2.23/NACE No.
12
,What is the minimum recommended distance away from an edge that an
inspector should take a measurement with a dial type magnetic pull off Dry
Film Thickness(DFT) gauge? - CORRECT ANSWERS - 2.5 cm (1 inch)
Polymerization is the process of? - CORRECT ANSWERS - Monomers
joining together.
An exposed area of the substrate or previous coat of a conductive material, often
caused by poor application technique is called: - CORRECT ANSWERS -
Holiday
Checking is: - CORRECT ANSWERS - a fine crack in the surface of a coating
that rarely reaches the substrate.
Inspection documentation is important because: - CORRECT ANSWERS -
Owners use the documentation for a variety of purposes.
An Inspectors personal log book should contain: - CORRECT ANSWERS -
No comments regarding the application team.
You have just received your NACE CIP Level 1 certification when you are
asked to supervise a team of uncertified field pipeline inspectors. Your FIRST
preferred course of action is to: - CORRECT ANSWERS - Review the NACE
Attestation prior to making a decision.
Good record can provide maintenance departments with detailed information
about ALL of the following EXCEPT: - CORRECT ANSWERS - How the
item was coated.
, Non Conformance Reports are completed by the Inspector: - CORRECT
ANSWERS - When the Inspector and Contractor deem it to be significant non
conforming item.
The initial steel condition is important to the NACE Inspector because: -
CORRECT ANSWERS - The Inspector may have to reject the steel.
The form of corrosion that has the largest potential for unexpected catastrophic
failure is: - CORRECT ANSWERS - Galvanic Corrosion
What is used to determine compressed air cleanliness? - CORRECT
ANSWERS - Profilometer
Osmotic blistering is most likely to occur as a result of: - CORRECT
ANSWERS - Airless spray application.
When performing tests for oil and grease using an ultra violet light, the NACE
Inspector should be aware that: - CORRECT ANSWERS - Synthetic oil or
grease may not be identified.
To achieve consistently accurate results with ALL alt test equipment: -
CORRECT ANSWERS - wash your hands before sampling.
When holiday testing is required the Inspector is always required to enforce
what standard? - CORRECT ANSWERS - NACE SP 0188
If the specifier does not identify a restriction level in accordance with SSPC PA
2, the default restriction level is: - CORRECT ANSWERS - Level 3
Fine cracks in the surface of a coating that rarely reach the substrate are called: -
CORRECT ANSWERS - Checking
