AUTO MANUAL DRIVE TRAIN
AUTO MANUAL DRIVE TRAIN EXAM QUESTIONS AND ANSWERS %
CORRECT.
Technician A says the clutch allows the engine to continue to run when
the vehicle is brought to a stop. Technician B says the clutch allows for
easier shifting of the gears. Who is correct? answer > c. Both A and B
Technician A says the pilot bushing aligns the flywheel to the
crankshaft. Technician B says the pilot bushing supports the
transmission input shaft. Who is correct? answer > b. Technician B
Which of the following components drives the manual transmission
input shaft? answer > b. Friction disc
All of the following are functions of a dual-mass flywheel except:
answer > d. Increase torque applied to the input shaft
A vehicle has a clutch slippage complaint; Technician A says the
pressure plate may be weak. Technician B says a faulty crankshaft rear
main seal could be the cause. Who is correct? answer > c. Both A and B
, AUTO MANUAL DRIVE TRAIN
Which of the following is the correct purpose of the clutch disc wave
springs? answer > b. Reduce clutch chatter
Technician A says the clutch is disengaged when the clutch pedal is
depressed. Technician B says the clutch is engaged when the clutch
pedal is depressed. Who is correct? answer > a. Technician A
Technician A says all clutch release bearings turn constantly against the
pressure plate. Technician B says that clutch release bearings are not
designed to operate to be constantly rotating against the pressure
plate. Who is correct? answer > d. Neither A or B
Clutch pedal free play sets the clearance between what two
components? answer > Clutch pedal free play sets the clearance
between what two components?
A whining noise is heard from the bell housing/transmission area when
the clutch pedal is depressed. The most likely cause is: answer > c.
Release bearing and pressure plate
Technician A says manual transaxles can be found in all types of
modern FWD, RWD, and 4WD vehicles. Technician B says transaxles are
used in FWD vehicles only. Who is correct? answer > b. Technician B
Technician A says self-shifting transmissions are basically manually
controlled automatic transmissions. Technician B says self-shifting
AUTO MANUAL DRIVE TRAIN EXAM QUESTIONS AND ANSWERS %
CORRECT.
Technician A says the clutch allows the engine to continue to run when
the vehicle is brought to a stop. Technician B says the clutch allows for
easier shifting of the gears. Who is correct? answer > c. Both A and B
Technician A says the pilot bushing aligns the flywheel to the
crankshaft. Technician B says the pilot bushing supports the
transmission input shaft. Who is correct? answer > b. Technician B
Which of the following components drives the manual transmission
input shaft? answer > b. Friction disc
All of the following are functions of a dual-mass flywheel except:
answer > d. Increase torque applied to the input shaft
A vehicle has a clutch slippage complaint; Technician A says the
pressure plate may be weak. Technician B says a faulty crankshaft rear
main seal could be the cause. Who is correct? answer > c. Both A and B
, AUTO MANUAL DRIVE TRAIN
Which of the following is the correct purpose of the clutch disc wave
springs? answer > b. Reduce clutch chatter
Technician A says the clutch is disengaged when the clutch pedal is
depressed. Technician B says the clutch is engaged when the clutch
pedal is depressed. Who is correct? answer > a. Technician A
Technician A says all clutch release bearings turn constantly against the
pressure plate. Technician B says that clutch release bearings are not
designed to operate to be constantly rotating against the pressure
plate. Who is correct? answer > d. Neither A or B
Clutch pedal free play sets the clearance between what two
components? answer > Clutch pedal free play sets the clearance
between what two components?
A whining noise is heard from the bell housing/transmission area when
the clutch pedal is depressed. The most likely cause is: answer > c.
Release bearing and pressure plate
Technician A says manual transaxles can be found in all types of
modern FWD, RWD, and 4WD vehicles. Technician B says transaxles are
used in FWD vehicles only. Who is correct? answer > b. Technician B
Technician A says self-shifting transmissions are basically manually
controlled automatic transmissions. Technician B says self-shifting
