Michigan Collision Repair Technician
Exam Practice Questions And Correct
Answers (Verified Answers) Plus
Rationale 2026 Q&A| Instant Download
Pdf
1. What is the primary purpose of measuring panel alignment before
performing repairs?
A. To check paint thickness
B. To ensure structural geometry is within specification
C. To determine welding spots
D. To identify rust areas
Accurate panel alignment ensures the vehicle’s structural geometry
meets manufacturer specifications before repair begins.
2. When welding on aluminum body panels, which technique is critical to
prevent warping?
A. High heat, slow movement
B. Low heat, quick movement
C. Continuously heating same spot
D. Overtorching for penetration
Aluminum welding requires controlled low heat and fast travel speed
to reduce distortion.
3. What does OEM stand for in collision repair?
A. Operational Equipment Manual
B. Optional Equipment Method
C. Original Equipment Manufacturer
D. Official Estimating Measure
, OEM refers to the company that originally produced the vehicle or
component.
4. During a structural repair, which area must remain protected to avoid
distortion?
A. Headlight housing
B. Unrelated structural weld points
C. Door handles
D. Trim clips
Protecting unaffected weld points prevents unintended distortion
during welding or pulling.
5. What tool is commonly used to check that a vehicle’s frame is square?
A. Torque wrench
B. Paint gauge
C. Frame measuring system
D. Panel removal tool
Frame measuring systems verify that the chassis is aligned accurately
to factory dimensions.
6. Which type of damage necessitates the replacement of a crumple
zone component?
A. Light paint scratches
B. Severe deformation beyond repair limits
C. Loose trim
D. Slight denting
Crumple zone components are designed to absorb impact and should
be replaced if deformed beyond safe repair.
7. What is the purpose of applying a corrosion protection coating after
welding?
A. To make it shiny
B. To prevent rust and corrosion
C. To enhance paint adhesion only
D. To increase weight
Corrosion protection coatings shield weld areas from moisture and
eventual rust.
8. In MIG welding steel, what gas mixture is typically used?
A. Oxygen only
, B. Argon/CO₂ mix
C. Helium only
D. Nitrogen
An argon/CO₂ mix provides a stable arc and good weld quality for
mild steel.
9. What does “joint fit-up” refer to in collision repair?
A. The paint job
B. The alignment and preparation of parts before welding
C. Sanding procedure
D. Glass removal
Joint fit-up means positioning, cleaning, and aligning panels before
final welding.
10. What is the purpose of a weld-through primer?
A. To add color
B. To protect against corrosion even when welded
C. To act as filler
D. To dull reflections
Weld-through primer allows welding while providing corrosion
protection under the joint.
11. When using a stud welder, what is the primary goal?
A. Remove paint
B. Pull dents without drilling holes
C. Measure panel thickness
D. Clean surfaces
Stud welders attach pins to pull dents while preserving the panel
surface.
12. What vehicle specification must be followed when replacing
body panels?
A. Tire inflation only
B. Manufacturer’s dimensional tolerances
C. Owner preference
D. Paint guideline only
Dimensional tolerances ensure the replacement panel is positioned
as intended by the OEM.
Exam Practice Questions And Correct
Answers (Verified Answers) Plus
Rationale 2026 Q&A| Instant Download
1. What is the primary purpose of measuring panel alignment before
performing repairs?
A. To check paint thickness
B. To ensure structural geometry is within specification
C. To determine welding spots
D. To identify rust areas
Accurate panel alignment ensures the vehicle’s structural geometry
meets manufacturer specifications before repair begins.
2. When welding on aluminum body panels, which technique is critical to
prevent warping?
A. High heat, slow movement
B. Low heat, quick movement
C. Continuously heating same spot
D. Overtorching for penetration
Aluminum welding requires controlled low heat and fast travel speed
to reduce distortion.
3. What does OEM stand for in collision repair?
A. Operational Equipment Manual
B. Optional Equipment Method
C. Original Equipment Manufacturer
D. Official Estimating Measure
, OEM refers to the company that originally produced the vehicle or
component.
4. During a structural repair, which area must remain protected to avoid
distortion?
A. Headlight housing
B. Unrelated structural weld points
C. Door handles
D. Trim clips
Protecting unaffected weld points prevents unintended distortion
during welding or pulling.
5. What tool is commonly used to check that a vehicle’s frame is square?
A. Torque wrench
B. Paint gauge
C. Frame measuring system
D. Panel removal tool
Frame measuring systems verify that the chassis is aligned accurately
to factory dimensions.
6. Which type of damage necessitates the replacement of a crumple
zone component?
A. Light paint scratches
B. Severe deformation beyond repair limits
C. Loose trim
D. Slight denting
Crumple zone components are designed to absorb impact and should
be replaced if deformed beyond safe repair.
7. What is the purpose of applying a corrosion protection coating after
welding?
A. To make it shiny
B. To prevent rust and corrosion
C. To enhance paint adhesion only
D. To increase weight
Corrosion protection coatings shield weld areas from moisture and
eventual rust.
8. In MIG welding steel, what gas mixture is typically used?
A. Oxygen only
, B. Argon/CO₂ mix
C. Helium only
D. Nitrogen
An argon/CO₂ mix provides a stable arc and good weld quality for
mild steel.
9. What does “joint fit-up” refer to in collision repair?
A. The paint job
B. The alignment and preparation of parts before welding
C. Sanding procedure
D. Glass removal
Joint fit-up means positioning, cleaning, and aligning panels before
final welding.
10. What is the purpose of a weld-through primer?
A. To add color
B. To protect against corrosion even when welded
C. To act as filler
D. To dull reflections
Weld-through primer allows welding while providing corrosion
protection under the joint.
11. When using a stud welder, what is the primary goal?
A. Remove paint
B. Pull dents without drilling holes
C. Measure panel thickness
D. Clean surfaces
Stud welders attach pins to pull dents while preserving the panel
surface.
12. What vehicle specification must be followed when replacing
body panels?
A. Tire inflation only
B. Manufacturer’s dimensional tolerances
C. Owner preference
D. Paint guideline only
Dimensional tolerances ensure the replacement panel is positioned
as intended by the OEM.
