FDNY G60 PRACTICE TEST EXAM
QUESTIONS AND ANSWERS GRADED A+
2025/2026
Sprinkler system must NOT be shut off or impaired while hot work is performed - ANS Place
damp cloth guards on individual sprinkler heads
The person conducting the fire watch ______ have other duties - ANS CANNOT
A portable fire extinguisher with a rating of _________ is required and should be within ____
feet travel distance hot work area - ANS 2-A:20-B:C///30
For ROOFING OPERATIONS, a portable fire extinguisher with a minimum rating of ______ is
required - ANS 3-A:40-B:C
Fire watch on floors below is ______ - ANS required
The fire watch must continue for a minimum of ____ minutes after the hot work is done -
ANS 30
For any CNG or LPG torch operations, the first inspection shall be conducted ___ minutes after
completion. The second inspection shall be conducted _______ after completion of torch
operations. - ANS 30 min///1 hour
1 @COPYRIGHT 2026 ALLRIGHTS RESERVED.
, The fire guard or fire watch personnel must complete a signed inspection report and it must be
submitted to and retained by the person in charge of the torch operations. - ANS The report
must be made available and maintained on the premises for a minimum of 48 hours after the
work is complete.
Most common fuel gasses used in blowtorches are ______ - ANS LPG (butane, propane)
natural gas (methane) (either CNG or piped natural gasses)
Soldering and brazing temperatures are typically______ - ANS 840 degrees F
Oxy-acetylene generates the highest temperature which can reach up to _____ - ANS 6000
degrees F
Gas torches can exceed _________ and are used for burning weeds, melting ice, or applying tar
to a roof - ANS 2000 degrees F
If the torch operation is to stop for a period of _________________, the torch vale must be
closed and the gas supply to the torch must be completely shut - ANS 1 hour or more
Containers, valves, regulators, hose and other apparatus and fittings for oxygen must be kept
free of __________. - ANS oil or grease
Backfire - ANS this occurs when the flame of a torch goes out and there is a loud snap or pop
Flashback - ANS This occurs when the cutting or welding flame burns inside the torch or the
hoses and it is usually accompanied by a whistle or hissing noise. As soon as it is noticed, the
torch control valves should be closed. This indicated there is something wrong with the
equipment, either damage or blockage
2 @COPYRIGHT 2026 ALLRIGHTS RESERVED.
QUESTIONS AND ANSWERS GRADED A+
2025/2026
Sprinkler system must NOT be shut off or impaired while hot work is performed - ANS Place
damp cloth guards on individual sprinkler heads
The person conducting the fire watch ______ have other duties - ANS CANNOT
A portable fire extinguisher with a rating of _________ is required and should be within ____
feet travel distance hot work area - ANS 2-A:20-B:C///30
For ROOFING OPERATIONS, a portable fire extinguisher with a minimum rating of ______ is
required - ANS 3-A:40-B:C
Fire watch on floors below is ______ - ANS required
The fire watch must continue for a minimum of ____ minutes after the hot work is done -
ANS 30
For any CNG or LPG torch operations, the first inspection shall be conducted ___ minutes after
completion. The second inspection shall be conducted _______ after completion of torch
operations. - ANS 30 min///1 hour
1 @COPYRIGHT 2026 ALLRIGHTS RESERVED.
, The fire guard or fire watch personnel must complete a signed inspection report and it must be
submitted to and retained by the person in charge of the torch operations. - ANS The report
must be made available and maintained on the premises for a minimum of 48 hours after the
work is complete.
Most common fuel gasses used in blowtorches are ______ - ANS LPG (butane, propane)
natural gas (methane) (either CNG or piped natural gasses)
Soldering and brazing temperatures are typically______ - ANS 840 degrees F
Oxy-acetylene generates the highest temperature which can reach up to _____ - ANS 6000
degrees F
Gas torches can exceed _________ and are used for burning weeds, melting ice, or applying tar
to a roof - ANS 2000 degrees F
If the torch operation is to stop for a period of _________________, the torch vale must be
closed and the gas supply to the torch must be completely shut - ANS 1 hour or more
Containers, valves, regulators, hose and other apparatus and fittings for oxygen must be kept
free of __________. - ANS oil or grease
Backfire - ANS this occurs when the flame of a torch goes out and there is a loud snap or pop
Flashback - ANS This occurs when the cutting or welding flame burns inside the torch or the
hoses and it is usually accompanied by a whistle or hissing noise. As soon as it is noticed, the
torch control valves should be closed. This indicated there is something wrong with the
equipment, either damage or blockage
2 @COPYRIGHT 2026 ALLRIGHTS RESERVED.
