NCCER ELECTRICAL LEVEL 3 MODULE 11
PRACTICE SCRIPT UPDATED 2026 TESTED
SOLUTIONS
⫸ A manual reversing starter uses ___. Answer: a mechanical interlock
⫸ Mechanically held relays would most likely be used in a ___.
Answer: hospital, auditoriums, churches
⫸ A single-contact device can be used to control multiple loads using a
___. Answer: multiple-pole relay
⫸ A furnace might use an on delay to ___. Answer: avoid blowing cold
air into the space when the system starts up
⫸ A type of relay controlled by a magnetic field is a(n) ___. Answer:
reed relay
⫸ A type of renewable overload device is a ___. Answer: melting alloy
relay
⫸ The operating coil of a relay is designed to work properly at ___.
Answer: 80% to 110% of the rated voltage
, ⫸ A device that allows relays to be controlled as a group while still
allowing individual switch control is a ___. Answer: master sequencer
⫸ Where low-voltage cable must be run parallel with high-voltage
cable, it should be separated by minimum of ___. Answer: 6" (150mm)
⫸ The function of a shading coil in a contactor is to ___. Answer:
prevent contact chatter and hum
⫸ What is the major difference between a contactor and a motor starter?
Answer: The starter provides overload protection while a contactor does
not.
⫸ The approximate inrush current of filament-type lamps is how many
times the normal operating current? Answer: 15 to 17
⫸ The maximum tungsten/infrared load amperage for a NEMA Size 2
magnetic contactor at 230V is ___. Answer: 30A
⫸ The maximum tungsten/infrared load amperage for a NEMA Size 00
magnetic contactor at 230V is ___. Answer: 5A
⫸ Which of the following best describes a control relay? Answer: An
electromagnetic device used in control circuits
PRACTICE SCRIPT UPDATED 2026 TESTED
SOLUTIONS
⫸ A manual reversing starter uses ___. Answer: a mechanical interlock
⫸ Mechanically held relays would most likely be used in a ___.
Answer: hospital, auditoriums, churches
⫸ A single-contact device can be used to control multiple loads using a
___. Answer: multiple-pole relay
⫸ A furnace might use an on delay to ___. Answer: avoid blowing cold
air into the space when the system starts up
⫸ A type of relay controlled by a magnetic field is a(n) ___. Answer:
reed relay
⫸ A type of renewable overload device is a ___. Answer: melting alloy
relay
⫸ The operating coil of a relay is designed to work properly at ___.
Answer: 80% to 110% of the rated voltage
, ⫸ A device that allows relays to be controlled as a group while still
allowing individual switch control is a ___. Answer: master sequencer
⫸ Where low-voltage cable must be run parallel with high-voltage
cable, it should be separated by minimum of ___. Answer: 6" (150mm)
⫸ The function of a shading coil in a contactor is to ___. Answer:
prevent contact chatter and hum
⫸ What is the major difference between a contactor and a motor starter?
Answer: The starter provides overload protection while a contactor does
not.
⫸ The approximate inrush current of filament-type lamps is how many
times the normal operating current? Answer: 15 to 17
⫸ The maximum tungsten/infrared load amperage for a NEMA Size 2
magnetic contactor at 230V is ___. Answer: 30A
⫸ The maximum tungsten/infrared load amperage for a NEMA Size 00
magnetic contactor at 230V is ___. Answer: 5A
⫸ Which of the following best describes a control relay? Answer: An
electromagnetic device used in control circuits