INSTANT PDF DOWNLOAD CUSP - T&D ACTUAL & EXAM
STUDY GUIDE COMPLETE QUESTIONS BANK AND
CORRECT DETAILED ANSWERS WITH RATIONALES ||
LATEST VERSION |
A high voltage utility or electrical company is authorized to use Complex Lockout
(tag permitting) under what regulatory condition: - SELECTED ANSWER 👀****
A variance application has been approved by the provincial authority.
Utilities often use a permitting system due to special circumstances of which
conventional lockout is impracticable. The following are justified approaches to
this process: - SELECTED ANSWER 👀**** 1. The isolation points are located
in remote areas with difficult or restricted access.
2. The length of time to perform the lockout is impracticable.
3. Excessive numbers of persons required to lockout.
Work on a distribution line must consider the following items when performing
isolation and de-energizing of the circuit.: - SELECTED ANSWER 👀**** 1.
Whether there are multiple sources of energy (loop feed) on the circuit.
2. Is the line isolating device capable of interrupting load.
3. Is the line to be subject to inductive or capacitive charge.
According to the CAN/ULC S801, what is the LEAST DESIRABLE type of fall
protection: - SELECTED ANSWER 👀**** Fall Arrest System (FAS)
,Within Z259.14 standards fall restriction equipment (FRE) may only be leather in
subcomponents or elements that are NOT exposed to: - SELECTED ANSWER
👀**** A dynamic load.
As per Z259 standards, energy absorbing lanyards shall be classified according
to their ability to absorb the kinetic energy from a fall as follows: - SELECTED
ANSWER 👀**** Class E4 (4.0 kN) and Class E6 (6.0 kN) energy absorbing
lanyards.
As per CAN/ULC S801, on an electrical distribution overhead utility line circuit,
verification of voltage absence can be achieved by: - SELECTED ANSWER
👀**** Using an approved voltage detector.
Isolation and tagging (no locks) is acceptable on an overhead distribution circuit
under some of the following conditions, EXCEPT for: - SELECTED ANSWER
👀**** The isolation can be operated from the ground directly at the base of a
structure.
Isolation and tagging (no locks) is acceptable for an overhead distribution circuit
under some of the following conditions: - SELECTED ANSWER 👀**** 1. The
isolation point is a physical and visual like a line cut or riser removed.
2. The isolation point can only be operated by the operating authority or qualified
worker.
3. The isolation point is protected from unauthorized access such as vertical
height spacing.
, Consider that a circuit has been isolated, tagged and grounded. workers
returning the next day must: - SELECTED ANSWER 👀**** Visually check
grounds to verify they are in good order, secure and test for voltage.
For lockout purposes, energy isolating devices shall be labelled or marked using
a standardized nomenclature and format to indicate their function. Identification
shall include: - SELECTED ANSWER 👀**** The equipment type, energy type,
and magnitude.
Utilities often use a permitting system due to special circumstances of which
conventional lockout is impracticable. The following is NOT a justified approach
to this process: - SELECTED ANSWER 👀**** The isolation points are only
simple single step actions.
Assuming that the fall protection system is correctly being used, in what
scenario might the worker still contact the ground if they fell: - SELECTED
ANSWER 👀**** Working 16 feet up in a bucket truck on distribution secondary
services using a six foot shock absorbing lanyard, connected to the approved
bucket anchor.
What is NOT defined as a requirement of temporary vertical life lines as per
Z259 standards: - SELECTED ANSWER 👀**** 100% polypropylene fibers
provide the greatest breaking strength.
STUDY GUIDE COMPLETE QUESTIONS BANK AND
CORRECT DETAILED ANSWERS WITH RATIONALES ||
LATEST VERSION |
A high voltage utility or electrical company is authorized to use Complex Lockout
(tag permitting) under what regulatory condition: - SELECTED ANSWER 👀****
A variance application has been approved by the provincial authority.
Utilities often use a permitting system due to special circumstances of which
conventional lockout is impracticable. The following are justified approaches to
this process: - SELECTED ANSWER 👀**** 1. The isolation points are located
in remote areas with difficult or restricted access.
2. The length of time to perform the lockout is impracticable.
3. Excessive numbers of persons required to lockout.
Work on a distribution line must consider the following items when performing
isolation and de-energizing of the circuit.: - SELECTED ANSWER 👀**** 1.
Whether there are multiple sources of energy (loop feed) on the circuit.
2. Is the line isolating device capable of interrupting load.
3. Is the line to be subject to inductive or capacitive charge.
According to the CAN/ULC S801, what is the LEAST DESIRABLE type of fall
protection: - SELECTED ANSWER 👀**** Fall Arrest System (FAS)
,Within Z259.14 standards fall restriction equipment (FRE) may only be leather in
subcomponents or elements that are NOT exposed to: - SELECTED ANSWER
👀**** A dynamic load.
As per Z259 standards, energy absorbing lanyards shall be classified according
to their ability to absorb the kinetic energy from a fall as follows: - SELECTED
ANSWER 👀**** Class E4 (4.0 kN) and Class E6 (6.0 kN) energy absorbing
lanyards.
As per CAN/ULC S801, on an electrical distribution overhead utility line circuit,
verification of voltage absence can be achieved by: - SELECTED ANSWER
👀**** Using an approved voltage detector.
Isolation and tagging (no locks) is acceptable on an overhead distribution circuit
under some of the following conditions, EXCEPT for: - SELECTED ANSWER
👀**** The isolation can be operated from the ground directly at the base of a
structure.
Isolation and tagging (no locks) is acceptable for an overhead distribution circuit
under some of the following conditions: - SELECTED ANSWER 👀**** 1. The
isolation point is a physical and visual like a line cut or riser removed.
2. The isolation point can only be operated by the operating authority or qualified
worker.
3. The isolation point is protected from unauthorized access such as vertical
height spacing.
, Consider that a circuit has been isolated, tagged and grounded. workers
returning the next day must: - SELECTED ANSWER 👀**** Visually check
grounds to verify they are in good order, secure and test for voltage.
For lockout purposes, energy isolating devices shall be labelled or marked using
a standardized nomenclature and format to indicate their function. Identification
shall include: - SELECTED ANSWER 👀**** The equipment type, energy type,
and magnitude.
Utilities often use a permitting system due to special circumstances of which
conventional lockout is impracticable. The following is NOT a justified approach
to this process: - SELECTED ANSWER 👀**** The isolation points are only
simple single step actions.
Assuming that the fall protection system is correctly being used, in what
scenario might the worker still contact the ground if they fell: - SELECTED
ANSWER 👀**** Working 16 feet up in a bucket truck on distribution secondary
services using a six foot shock absorbing lanyard, connected to the approved
bucket anchor.
What is NOT defined as a requirement of temporary vertical life lines as per
Z259 standards: - SELECTED ANSWER 👀**** 100% polypropylene fibers
provide the greatest breaking strength.
