4th Class Power Engineering Unit A8: Basic Concepts in
Electrotechnology Questions With COMPLETE
sOLUTIONS
A 6 pole alternator producing 60 Hz power must turn at:
Select one:
a. 1800 rpm
b. 2400 rpm
c. 1000 rpm
d. 1200 rpm Correct Answers d
A clamp-on ammeter measures current flow by using:
Select one:
a. differential voltage
b. differential current flow between two conductors
c. a basic transformer principle
d. a portion of circuit resistance Correct Answers b
A closed electrical circuit will:
Select one:
a. allow current to flow
b. not allow current to flow
c. be series wound
d. contain an open switch or relay contact Correct Answers a
A conductor supplied with current while in a magnetic field will:
Select one:
a. tend to move at right angles to the flux lines
b. tend to remain stationary
c. want to move with the flux lines
d. have a current induced into it Correct Answers a
,A current carrying conductor being moved by a magnetic field is
the principle known as:
Select one:
a. magnetic flux
b. motor action
c. hydro-electrics
d. generator action Correct Answers b
A device used to change the voltage and current from one level
to another, is known as a/an:
Select one:
a. conductor
b. resistor
c. alternator
d. transformer Correct Answers d
A device used to measure the potential difference between two
points is the:
Select one:
a. ammeter
b. clamp-on ammeter
c. megohmmeter
d. voltmeter Correct Answers d
A kilowatt hour meter has a small motor which:
Select one:
a. turns at a constant speed
b. slows down as power consumption increases
c. has a speed proportional to power consumption
d. moves the meter demand pointer Correct Answers c
,A material with high conductance is:
Select one:
a. poor conductor
b. highly resistant to electrical flow
c. not suitable for high voltage
d. good conductor Correct Answers d
A moving conductor is at an angle of 90 degrees within the
magnetic field:
Select one:
a. maximum resistance to current flow is attained
b. current will flow with the least resistance
c. motor action will be experienced
d. voltage generated will be at its maximum Correct Answers d
A property of a magnet, is that it will always point in the north
direction:
Select one:
a. freely suspended in the air
b. charged with electricity
c. it is demagnetized
d. in the presence of iron filings Correct Answers a
A short length of wire or flat metal strip made from an alloy
with a low melting point is a:
Select one:
a. fuse
b. breaker
c. plug conductor
d. reset device Correct Answers a
, A shunt type DC generator has __________ output voltage:
Select one:
a. very high
b. nearly constant
c. very low
d. erratic Correct Answers b
A transformer has a primary voltage of 440 volts and 20 turns on
the primary winding. If the secondary winding has 10 turns the
voltage of the secondary is:
Select one:
a. 220 volts
b. 200 volts
c. 880 volts
d. 22 volts Correct Answers a
A transformer has a primary voltage of 440 volts and 20 turns on
the primary winding. If the secondary winding has 10 turns the
voltage of the secondary is:
Select one:
a. 220 volts
b. 200 volts
c. 880 volts
d. 22 volts Correct Answers a
A transformer has a primary voltage of 500 volts and 20 turns on
the primary winding. If the secondary winding has 5 turns the
voltage of the secondary is:
Select one:
a. 2000 volts
Electrotechnology Questions With COMPLETE
sOLUTIONS
A 6 pole alternator producing 60 Hz power must turn at:
Select one:
a. 1800 rpm
b. 2400 rpm
c. 1000 rpm
d. 1200 rpm Correct Answers d
A clamp-on ammeter measures current flow by using:
Select one:
a. differential voltage
b. differential current flow between two conductors
c. a basic transformer principle
d. a portion of circuit resistance Correct Answers b
A closed electrical circuit will:
Select one:
a. allow current to flow
b. not allow current to flow
c. be series wound
d. contain an open switch or relay contact Correct Answers a
A conductor supplied with current while in a magnetic field will:
Select one:
a. tend to move at right angles to the flux lines
b. tend to remain stationary
c. want to move with the flux lines
d. have a current induced into it Correct Answers a
,A current carrying conductor being moved by a magnetic field is
the principle known as:
Select one:
a. magnetic flux
b. motor action
c. hydro-electrics
d. generator action Correct Answers b
A device used to change the voltage and current from one level
to another, is known as a/an:
Select one:
a. conductor
b. resistor
c. alternator
d. transformer Correct Answers d
A device used to measure the potential difference between two
points is the:
Select one:
a. ammeter
b. clamp-on ammeter
c. megohmmeter
d. voltmeter Correct Answers d
A kilowatt hour meter has a small motor which:
Select one:
a. turns at a constant speed
b. slows down as power consumption increases
c. has a speed proportional to power consumption
d. moves the meter demand pointer Correct Answers c
,A material with high conductance is:
Select one:
a. poor conductor
b. highly resistant to electrical flow
c. not suitable for high voltage
d. good conductor Correct Answers d
A moving conductor is at an angle of 90 degrees within the
magnetic field:
Select one:
a. maximum resistance to current flow is attained
b. current will flow with the least resistance
c. motor action will be experienced
d. voltage generated will be at its maximum Correct Answers d
A property of a magnet, is that it will always point in the north
direction:
Select one:
a. freely suspended in the air
b. charged with electricity
c. it is demagnetized
d. in the presence of iron filings Correct Answers a
A short length of wire or flat metal strip made from an alloy
with a low melting point is a:
Select one:
a. fuse
b. breaker
c. plug conductor
d. reset device Correct Answers a
, A shunt type DC generator has __________ output voltage:
Select one:
a. very high
b. nearly constant
c. very low
d. erratic Correct Answers b
A transformer has a primary voltage of 440 volts and 20 turns on
the primary winding. If the secondary winding has 10 turns the
voltage of the secondary is:
Select one:
a. 220 volts
b. 200 volts
c. 880 volts
d. 22 volts Correct Answers a
A transformer has a primary voltage of 440 volts and 20 turns on
the primary winding. If the secondary winding has 10 turns the
voltage of the secondary is:
Select one:
a. 220 volts
b. 200 volts
c. 880 volts
d. 22 volts Correct Answers a
A transformer has a primary voltage of 500 volts and 20 turns on
the primary winding. If the secondary winding has 5 turns the
voltage of the secondary is:
Select one:
a. 2000 volts