IRONWORKER NCCER EXAM COMPLETE QUESTIONS AND
100% VERIFIED ANSWERS LATEST VERSION (PASS
GUARANTEE)
1. Q: What is the primary role of an ironworker?
ANSWER To install, connect, and repair iron and steel structures in
construction projects.
2. Q: What are the three main types of ironworkers?
ANSWER Structural ironworkers, reinforcing ironworkers, and ornamental
ironworkers.
3. Q: What does OSHA stand for?
ANSWER Occupational Safety and Health Administration.
4. Q: What is the minimum safety factor for rigging equipment?
ANSWER Typically 5:1 for rigging hardware.
5. Q: What does PPE stand for?
ANSWER Personal Protective Equipment.
6. Q: Name three essential pieces of PPE for ironworkers.
ANSWER Hard hat, safety glasses, and steel-toed boots.
7. Q: What is a competent person on a job site?
, ANSWER Someone capable of identifying hazards and authorized to take
corrective action.
8. Q: At what height does fall protection become mandatory?
ANSWER Generally at 6 feet or more, though some standards require it at
lower heights.
9. Q: What is the purpose of a toolbox talk?
ANSWER To discuss safety topics and job-specific hazards before starting
work.
10. Q: What does SDS stand for?
ANSWER Safety Data Sheet.
## Module 2: Tools and Equipment
11. Q: What is a spud wrench used for?
ANSWER Aligning bolt holes and tightening bolts in structural steel
connections.
12. Q: What is the purpose of a bull pin?
ANSWER To align holes in steel members during assembly.
13. Q: What type of hammer is commonly used by ironworkers?
ANSWER A sleever bar or engineer's hammer.
14. Q: What is a drift pin used for?
ANSWER Aligning bolt holes in structural steel members.
,15. Q: What is the purpose of a come-along?
ANSWER A hand-operated winch used for pulling or tensioning.
16. Q: What is a choker hitch?
ANSWER A rigging configuration where the sling wraps around the load
and through itself.
17. Q: What tool is used to cut structural steel on site?
ANSWER Cutting torch, plasma cutter, or band saw.
18. Q: What is a snatch block used for?
ANSWER To change the direction of a line or increase lifting capacity.
19. Q: What is the purpose of a level?
ANSWER To ensure structural members are plumb and level.
20. Q: What is a centerpunch used for?
ANSWER Making indentations to mark drilling locations.
## Module 3: Rigging Practices
21. Q: What is the working load limit (WLL)?
ANSWER The maximum load that should be applied to rigging
equipment under normal conditions.
22. Q: How do you determine the capacity of a sling in a basket hitch?
ANSWER Multiply the vertical hitch capacity by 2.
, 23. Q: What angle should you maintain when using slings?
ANSWER Sling angles should be 60 degrees or greater from horizontal
for optimal capacity.
24. Q: What is shock loading?
ANSWER A sudden, rapid application of force that can exceed equipment
capacity.
25. Q: When should rigging equipment be inspected?
ANSWER Before each use and periodically according to manufacturer
specifications.
26. Q: What is the safe approach to a suspended load?
ANSWER Never walk or work under a suspended load.
27. Q: What is a tagline used for?
ANSWER To control and guide a suspended load during lifting
operations.
28. Q: What reduces sling capacity most significantly?
ANSWER Decreasing sling angle from vertical.
29. Q: What is the hand signal for "stop"?
ANSWER Arm extended, palm down, moving side to side.
30. Q: What should you do if rigging equipment shows signs of damage?
ANSWER Remove it from service and tag it for inspection or disposal.
## Module 4: Structural Steel Erection
100% VERIFIED ANSWERS LATEST VERSION (PASS
GUARANTEE)
1. Q: What is the primary role of an ironworker?
ANSWER To install, connect, and repair iron and steel structures in
construction projects.
2. Q: What are the three main types of ironworkers?
ANSWER Structural ironworkers, reinforcing ironworkers, and ornamental
ironworkers.
3. Q: What does OSHA stand for?
ANSWER Occupational Safety and Health Administration.
4. Q: What is the minimum safety factor for rigging equipment?
ANSWER Typically 5:1 for rigging hardware.
5. Q: What does PPE stand for?
ANSWER Personal Protective Equipment.
6. Q: Name three essential pieces of PPE for ironworkers.
ANSWER Hard hat, safety glasses, and steel-toed boots.
7. Q: What is a competent person on a job site?
, ANSWER Someone capable of identifying hazards and authorized to take
corrective action.
8. Q: At what height does fall protection become mandatory?
ANSWER Generally at 6 feet or more, though some standards require it at
lower heights.
9. Q: What is the purpose of a toolbox talk?
ANSWER To discuss safety topics and job-specific hazards before starting
work.
10. Q: What does SDS stand for?
ANSWER Safety Data Sheet.
## Module 2: Tools and Equipment
11. Q: What is a spud wrench used for?
ANSWER Aligning bolt holes and tightening bolts in structural steel
connections.
12. Q: What is the purpose of a bull pin?
ANSWER To align holes in steel members during assembly.
13. Q: What type of hammer is commonly used by ironworkers?
ANSWER A sleever bar or engineer's hammer.
14. Q: What is a drift pin used for?
ANSWER Aligning bolt holes in structural steel members.
,15. Q: What is the purpose of a come-along?
ANSWER A hand-operated winch used for pulling or tensioning.
16. Q: What is a choker hitch?
ANSWER A rigging configuration where the sling wraps around the load
and through itself.
17. Q: What tool is used to cut structural steel on site?
ANSWER Cutting torch, plasma cutter, or band saw.
18. Q: What is a snatch block used for?
ANSWER To change the direction of a line or increase lifting capacity.
19. Q: What is the purpose of a level?
ANSWER To ensure structural members are plumb and level.
20. Q: What is a centerpunch used for?
ANSWER Making indentations to mark drilling locations.
## Module 3: Rigging Practices
21. Q: What is the working load limit (WLL)?
ANSWER The maximum load that should be applied to rigging
equipment under normal conditions.
22. Q: How do you determine the capacity of a sling in a basket hitch?
ANSWER Multiply the vertical hitch capacity by 2.
, 23. Q: What angle should you maintain when using slings?
ANSWER Sling angles should be 60 degrees or greater from horizontal
for optimal capacity.
24. Q: What is shock loading?
ANSWER A sudden, rapid application of force that can exceed equipment
capacity.
25. Q: When should rigging equipment be inspected?
ANSWER Before each use and periodically according to manufacturer
specifications.
26. Q: What is the safe approach to a suspended load?
ANSWER Never walk or work under a suspended load.
27. Q: What is a tagline used for?
ANSWER To control and guide a suspended load during lifting
operations.
28. Q: What reduces sling capacity most significantly?
ANSWER Decreasing sling angle from vertical.
29. Q: What is the hand signal for "stop"?
ANSWER Arm extended, palm down, moving side to side.
30. Q: What should you do if rigging equipment shows signs of damage?
ANSWER Remove it from service and tag it for inspection or disposal.
## Module 4: Structural Steel Erection
